Make your own dollhouse drawings. Do-it-yourself cardboard dollhouse. Let's get started

Andrey Vogachev talked about how to make it yourself. He noticed that his daughter was enthusiastically playing with houses the size of a cardboard shoe box. The idea arose to do something solid. Searching the stores didn't turn up anything worthwhile, they were either very small or too expensive. I thought it wouldn't be too difficult to make it myself. After searching on the Internet, I found decent sizes, from which I subsequently plan to make a house.

In the drawing, the cutting markings are marked with red lines on how to cut plywood in the store. Please note that the more accurately you can mark and cut in the store, the less time it will take later. The shop cut it very accurately, while doing it yourself can introduce some flaws.

Drawing of a doll's house

Plywood dimensions 1.5 x 1.5 m. Weight 16 kg. Total area 2.3 square meters. Sanded plywood.

After cutting, all the parts began to look different large volume. White paint for facades. Small carnations. Glue and brush.

Markup process

All parts need to be trimmed. It's a small matter. Drill holes and cut out parts of the balcony. Continue from 5 minutes.

The stores offer customers a wide range of all kinds of toys, including doll houses. Every girl dreams of getting one of them, while parents can easily make a beautiful and strong house for dolls in just a few days. Moreover, the child will be able to take an active part in the process and express all his wishes regarding size and design. To do Dollhouse do it yourself from plywood, you will need a diagram that you can draw yourself or find a ready-made one on the Internet.

We make a drawing of a dollhouse from plywood with the dimensions of all structural elements

A toy house and plywood cannot be built without a detailed drawing, which will show the dimensions of all its parts. To do this, you must first determine the approximate dimensions of the future house and imagine what shape it will be.

When reducing or increasing the structure, it should be remembered that all dimensions should also be changed proportionally.

The house consists of the following parts:

Rear wall: pentagon shaped. Its sides are 76 cm, and its base is 106 cm. The upper side is an uneven triangle, the apex of which is at a height of 91 cm.
Gender: has rectangular shape. Its dimensions are 106x38 cm.
Second floor ceiling: rectangle with dimensions 104x36 cm.
Side wall (2 parts): is a rectangle 36x76 cm.
Internal wall with right side: rectangle 25x50 cm.
Internal wall on the left side: rectangle 25x43 cm.
Left side of the roof: rectangle measuring 76x39 cm.
Right side of the roof: rectangle with parameters 45x39 cm.

How to make a dollhouse with your own hands from plywood: step-by-step guide

After cutting out the parts using a jigsaw or hacksaw, you need to carefully sand them with fine sandpaper, and then begin assembly. At this stage, windows of arbitrary sizes are cut out and also carefully processed with sandpaper.

Making a house step by step:

The side walls are attached to the base using self-tapping screws and construction glue, and then the ceiling of the second floor and internal partitions.
The roof is being installed.
Decorative tiles made of cardboard, colored paper or other materials are glued to the roof.
Next, the house is painted with paints (acrylic, gouache, watercolor);
The rooms are covered with wallpaper, fabric, film.
The floors are covered with pieces of linoleum, laminate, carpet, and felt.
Furniture and interior items are being placed.

Near the house you can make a small garden, placed in a box, in which trees cut out of cardboard will grow.

If the parts were not cut too smoothly and a gap has formed between them, then it can be covered with wood putty and then painted over.

How to assemble a plywood house for children with your own hands quickly and easily

A small plywood house designed for games will appeal to any child. After all, he will have his own personal space there. It is not difficult to assemble such a structure yourself if you first make drawings and cut out the parts.

What you will need for work:

Sheets of plywood, the thickness of which is at least ten millimeters. The required quantity can be easily determined by adding up all the areas of future parts.
Timber for the frame measuring 40x40 or 50x50 mm.
Plexiglas or plastic for windows.
Door awnings.
Finishing materials (wallpaper, non-toxic paint, putty).

Blanks are made from timber and plywood and sanded with sandpaper until completely smooth. The frame is assembled from timber, and plywood blanks are attached to it. Next, windows and doors are installed. Then the house can be painted outside and inside or covered with wallpaper. Furniture is brought in. You can make decorations from leftover plywood and install them around the house. The children's playhouse is ready.

The fastening elements must be hidden so that the child cannot be injured.

We make a castle from plywood with our own hands: drawings and recommendations

Plywood is one of the easiest materials to process, so it can be used to make not only simple houses, but also beautiful castles for princesses and knights. To do this, you need to be patient and carefully draw every detail of the future castle. The drawings are made in a similar way to the drawings of a doll's house, but towers, balconies and terraces are added to the details. There are a lot of themed sites interesting models, which are easy to build yourself.

Tools required for work:

The pencil is simple;
Ruler (simple and curly);
Jigsaw;
Screwdrivers or screwdriver;
Hammer;
Sandpaper;
Tassels;
Fastening elements.

You can use ice cream sticks to fence balconies.

Beautiful furniture for dolls made of plywood: drawings and manufacturing methods

Almost any furniture can be made from plywood. toy house: beds, tables, chairs, cabinets, sofas, shelves. The furniture made according to the drawings turns out to be quite large, so it is suitable for both Barbie dolls and baby dolls.

Furniture parts can be glued or connected with self-tapping screws and furniture nails. Basically, plywood is taken, about 4 mm thick.

What you need to make furniture:

Pencil and paper;
Hand jigsaw;
Fine sandpaper;
Liquid nails or wood glue;
Paints and varnish.

When assembling small furniture, it is better to use glue, because fasteners can damage the parts.

For all furniture parts, you first need to draw and cut out a template. Then trace it on the plywood and cut out the structural elements with a jigsaw. The edges are sanded. The parts must be connected to each other, and then painted and varnished or covered with fabric using a stapler.

Making a house out of plywood for a doll with your own hands (video instructions)

You can make durable and beautiful toys from plywood that will delight your child for a long time. If you have drawings, free time and a little patience, this will not be difficult even for those who do not have any skills in this matter. And by showing your imagination, you can create real masterpieces that will cause surprise and delight not only in the child, but also in those around you.

Making a dollhouse with your own hands is an exciting activity for the whole family, where children, by watching and helping, gain skills in working with tools, planning, decorating, and develop a sense of harmony. Adults can fully realize their creative potential and involve the whole family in teamwork.

Impressions from the process and the result will remain in the memory for a long time, even from transforming an ordinary box.

The choice of materials for building a house with your own hands should coincide with financial capabilities, the amount of free time and the level of skill.

Paper. Scrapbooking paper is suitable for these purposes: it is thick, does not fade, and has wide choose textures and prints. Ready-made schemes Can be printed on regular office paper.
Cardboard. Ideal options will become bookbinding, beer, corrugated three-layer. The latter is more difficult to cut, but more affordable (for example, household appliances or weighted candies are usually packaged in it). The rigidity of cardboard allows you to add more floors to the project.
Boxes. Their characteristics do not differ from the previous material. One large or several medium-sized ones, always whole boxes, are suitable for work.
Plywood. It is distinguished by its availability, ease of processing, the ability to implement complex projects, and its price-quality ratio. At the same time, it requires certain skills in working with sawing tools and precise design. The recommended plywood thickness is at least 6-7 mm. You should definitely pay attention to the E0 marking - its presence confirms the low formaldehyde content.
Tree. The material is more expensive and difficult to work with, requiring expensive tools. Suitable for making large-sized multifunctional shelving houses.

Comparative characteristics of materials:

Material	Price	Durability	Complexity
Paper house	Very cheap	Low	Very easy
Cardboard house	Cheap	Low	Easy but requires patience
House made of boxes	Very cheap	Low	Very easy
Plywood house	Moderately expensive	High	Medium difficulty, requires tool skills
Wooden house	More expensive than average, but cheaper than store bought	Very high	Complex, cutting on professional equipment is advisable

Drawings and dimensions of a paper house

The dimensions of a paper house are limited only by the size and density of the material used. Large models made from thin paper will not hold their shape. In cases where the material is dense but small in size, the house is assembled from individual parts.

The peculiarity of the paper house drawing is that it is made up of a single canvas.

At the junctions of the walls, as well as on the roof slopes, additional narrow strips are provided for applying glue or double sided tape. In the finished printouts, the houses are drawn in detail; all that remains is to cut them out and glue them together. Creating a sketch yourself leaves room for creativity and layering when decorating.

Paper house option:

4 open rooms separated by two sheets of paper.
The basic drawing consists of 2 rectangular parts with transverse slots in the middle. The depth of the cuts is up to half the width of the elements.
The dimensions of the blanks correspond to the height and double length of the future rooms.

Paper house for dolls

To work you will need a drawing, scissors and glue.

With their help you need:

Carefully cut the workpiece along the contour.
Fold along the dotted lines, giving the model volume.
Apply glue to the special valves provided in the drawing.
Glue the house together.
Decorate with textured printed paper.

Such models do not imply interior decoration and act as the scenery around which the game takes place.

The disadvantage of the model is that it can be conventionally called a dollhouse, since the entire structure is very schematic. But this house provides a play space. The child has the opportunity to create an interior in each room and freely move the doll inside. At the same time, the design takes up little space and can be easily disassembled or folded for storage.

The work comes down to two steps:

Cut both elements taking into account the windows, doors and central slots.
Connect the parts with cuts facing each other.

Next, you should decorate each room as you wish. Based on this drawing, you can create more complex models. For example, if you lengthen one of the elements and make 2 slots instead of 1, inserting one base part into each of them, you will get a 6-room house.

Cardboard house drawings

You can outline the details right away on cardboard, but it is much more convenient to have the entire list before your eyes necessary elements, their number and size.

A schematic representation of the component parts of the house is enough, the main thing is to take them all into account:

Side wall (2 pcs.): a rectangle, the height of which is equal to the uppermost interfloor ceiling, and the width is the desired depth of the rooms.
Back wall(1 piece): a rectangle with a width equal to the length of the house and the same height as the side walls.
Gable(2 pcs.): an isosceles right triangle whose hypotenuse is equal to the width of the side wall.
1st floor floor(1 pc.): a rectangle with a height equal to the width of the side walls, and a length equal to the width of the back wall.
Interfloor ceiling(1 pc.): floor part of the same dimensions, but with a cut-out staircase opening.
Interior partition(1 pc.): U-shaped figure with a width equal to the depth of the house and a height corresponding to the height of one floor.
Roof(1 pc.): a large rectangle, the height of which is slightly more than the amount There are 2 gable legs, and the length is slightly longer than the length of the house.

If there is a large piece of cardboard, the quantity individual elements can be reduced, combining the side walls, gables, floor of the 1st floor and the rear wall into one part in the drawing. Doorways will not be needed if the interior partitions are made one third narrower than the width of the house.

Connecting rooms

It is more convenient to connect the walls with wide masking tape. It does not damage the cardboard when removed, does not make the work sloppy and does not interfere with decoration. Adhesive Moment Crystal will help fix cardboard walls relative to each other: it sets quickly and leaves no marks.

To connect the walls to each other you should:

Coat the cut of the side wall with glue and press it tightly against the edge of the rear wall, trying to maintain an angle of 90 degrees.
Cover the resulting corner masking tape from the outside and inner sides, so that the middle of the adhesive tape is at the junction of the walls.
Similarly, attach the second side wall, forming a U-shaped frame for the future house.
Coat the cut of the floor part with glue on three sides, press it to the edges of the walls, adjusting at the same time internal corners house.
Reinforce each joint between the floor and the wall with adhesive tape on the outside and inside.
Apply glue to those sections of the inner wall that will be attached to the floor and the back of the house.
Press the part strictly perpendicular to the floor and parallel to the side walls of the house (recheck the distance between the walls below and above with a ruler, adjust if necessary).
Cover the resulting corners on both sides of the partition with masking tape.

Taping the corners on both sides will make the structure stronger, will fix the shape more rigidly. To ensure a tighter fit of the tape to the surface, it is recommended to forcefully iron the gluing areas with the edge of a ruler or plastic card.

Connecting ceilings to floors

The ceiling of one floor is the floor of the next. To prevent peeling and sagging, the interfloor ceiling is secured to a support.

For accuracy, it is recommended to draw a line along the perimeter of the frame at the level of the upper boundaries interior walls parallel to the floor of the floor.
Cut out long strips of cardboard no more than 1 cm wide. If the material is not thick enough, the strips can be cut twice as large and glued together.
Glue the resulting parts with the wide side around the perimeter of the house, aligning with the control line. There should be a uniform protrusion that encircles the outer walls from the inside.
Apply glue to the sections of all the parts on which the ceiling will lie, as well as the sections of the ceiling itself.
Lay the ceiling piece, making sure the internal walls are perpendicular.
Tape the joints of the walls and floor with masking tape top floor, making sure that the tape lies all the way to the corner without deforming it.

DIY dollhouse from a box

It is easier and faster to build a dollhouse from boxes with your own hands than from individual sheets of cardboard.

For work you will need following materials and tools:

cardboard box from large household appliances;
marker;
scissors, stationery knife;
masking tape, glue;
colored paper, braid, pieces of fabric - everything that can be useful in decorating a finished house.

Before starting work, you need to make sure there are no defects on the cardboard, cut off excess tape and remove the staples from the stapler.

Mark the middle of the box with a marker. It is convenient to take the connection line of the folding parts of the box as a guide.
Cut along the line into 2 equal parts. One half will serve as the basis for the house.
One of the folding parts will become the floor of the first floor. It should be secured to the side walls of the box using tape.
Cut off the corners of the opposite flap to form a roof gable
At this stage, until additional volumetric parts are glued in, it is more convenient to cut through windows and doors. First you need to mark the future location with a marker interfloor ceilings. This will allow you to choose the correct location of the windows. It's easier to cut them out stationery knife. Cut the front door on one of the side walls of the house.
Cut off both opening parts from the second half of the box. They will serve as floors for the second floor and attic. Make an opening for the stairs for each part: cut the upper left part in the shape of a small square or rectangle.
Using tape, attach the ceilings along the previously marked lines. Openings for stairs should be in opposite, inner corners of the house.
Cut the roof slopes from the side walls of the remaining part of the box. Use tape to glue them to the pediment and walls. Cover the top corner of the roof with tape.
Attach cardboard ladders to the openings in the floor.

A doll house made from boxes can be furnished with homemade furniture

The construction of the dollhouse from the box is completed. All that remains is to decorate it and arrange the furniture.

Features of working with plywood

Dollhouses made of plywood are lightweight, environmentally friendly, and relatively low in cost. But, unlike houses made of boxes, plywood ones are stronger, withstand heavy loads and last longer. When choosing this material, it is necessary to take into account the features of its processing.

The tool for cutting parts must be very sharp and selected in accordance with the thickness of the sheet: up to 1.5 mm - can be cut with a knife, 1.5-6 mm - with a hand jigsaw, over 6 mm - with a jigsaw.
It is advisable to saw the sheet along the grain. In the case of a transverse direction, it is recommended to make several cuts along the entire length of the future cut, which will reduce the likelihood of cracks and chips.
Finished parts should be thoroughly sanded.
It is better to connect parts using wood glue. The connection will be stronger if the fibers of the bonded surfaces are in the same direction.
For nails and screws, you need to pre-drill holes and place washers under the heads.

Compliance with these rules will make the work easier and protect against unnecessary consumption of material.

Required tools and materials

Making a dollhouse from plywood is possible for anyone with minimal skills in working with tools, desire and patience.

To build a house you will need the following tools and materials:

plywood 6-7 mm thick;
narrow wooden slats;
small nails or a construction stapler;
jigsaw (can be replaced with a manual one);
drill with thin drill;
sandpaper for processing the edges of parts;
wood glue;
mounting tape;
a simple pencil and tape measure;
decor for decorating a finished house.

The amount of material is calculated according to the drawing and depends on the size of the project.

For example, for a small tabletop house you will need 4-6 main parts, while for the construction of a floor house multi-storey building 4-6 sheets of plywood can be used. For accurate calculation, the finished sketch is disassembled into components, and for each element a detailed drawing.

After the parts are completely laid out on paper, the total area of the required material is calculated.

Drawings for a plywood house

A dollhouse made from boxes with your own hands can serve as a model for self-creation drawing. A visual model, no matter how complex it may be, will allow you to evaluate the scale of the idea, the actual dimensions of the product, identify the features of the main parts and possible weak points of the design.

Story about creating a dollhouse from plywood:

For the simplest house with a pitched roof, you will need drawings of the basic elements.

Side walls with opening for front door. The difference in the height of the walls will determine the angle of the roof.
Rear wall including pediment. The height differences on opposite sides must correspond to the side parts.
Shed roof.
The base should extend beyond the house for better stability.
Interfloor ceilings with staircase openings, which are located in opposite corners so that they do not end up under the stairs leading to the floor above.
Interior partitions with arched doorways.

Window openings are located on back wall, side elements and roof according to the sketch. A front opening cover can be added if desired. In this case, it is more appropriate to place windows on it. The dimensions of the parts depend on the available space where the house according to individual wishes will stand.

The height of the floors should be comfortable for playing - this is 40-50 cm.

It is recommended to install the uppermost ceiling (attic or loft) no higher than the child’s eye level. Too much deep rooms not convenient for playing, especially on the extreme floors. Under the folding roof you can place a hidden attic box, where doll outfits will be stored.

Step-by-step instructions for a plywood house

A do-it-yourself doll house from boxes can be assembled in a couple of hours without a preliminary drawing, unlike a plywood house, where precision and accuracy are very important, which require time. Carefully double-checking all dimensions will make it easier to fit and assemble the elements.

Carefully and accurately transfer the image of the elements onto a sheet of plywood using a template and a pencil.
Using an electric jigsaw you can cut parts faster and with better quality.
For sawing window openings Make auxiliary holes with a narrow drill bit. Cut along the contour of the window and door.
All cuts of each element must be sanded to avoid splinters and scratches.
On the prepared parts, mark with a simple pencil the location of interfloor ceilings and internal partitions.
It is more convenient to start assembly with gluing external walls, strengthening the outer corners mounting tape.
Glue internal elements according to the markings.
Connect both pieces. For more reliable fastening of the ceilings, it is recommended to attach ceiling moldings from slats or narrow strips of plywood.
Glue the roof slope to the gable and side walls.
Glue the finished house to the base.
Reinforce all joints of parts with mounting tape. Leave the house for a day for the glue to dry completely.
For facade decoration, as one of the options, it is used acrylic paint on wood.
When decorating the interior, choose available materials that do not create large loads: paper, fabric, pieces of fur.
To make the stairs you will need rectangular pieces of plywood with a width equal to the openings prepared in the floors. The steps are made from cut narrow slats with a triangular cross-section, thin wooden blocks sawn diagonally or strips of corrugated cardboard.

Stairs are installed after the internal ones finishing works so as not to create hard-to-reach areas.

Wooden house master class

A do-it-yourself dollhouse made from boxes or plywood has one significant drawback: fragility of the structure. Large models, combining the functions of a chest of drawers or a rack, require reliable fastenings and are made of wood.

At the time of buying sheet material It makes sense to immediately order cutting of parts.

This will reduce labor costs and compensate for the lack of expensive tools. The cut line made using professional equipment is more accurate and even, which will make it much easier further processing tree. But, even in this case, the process of making a house remains quite difficult for inexperienced craftsmen.

You can simplify the task by using the old wooden furniture as a finished base.

To work, you need to prepare materials and tools according to the list:

Wooden rack.
Wood putty.
A sheet of plywood 20-25 mm thick.
Fiberboard sheet for interior partitions and the back wall of the house.
Drill-driver, set of drills and screws.
Wood glue, masking tape, liquid nails
Sandpaper.
Primer and white acrylic paint, universal colors of orange and brown colors, varnish
Decoration materials.
Scissors, pencil, ruler, tape measure.
Thick cardboard.
Brush and roller.
Construction stapler or small nails and a hammer.
Hand jigsaw.

The list may vary slightly depending on the condition of the furniture being remodeled and the choice of finishing.

Your little princess is growing by leaps and bounds. And now you have already equipped her children's room, which is full of toys. But as always, something is missing. Or maybe make a dollhouse with your own hands from plywood? Its scheme is simple. Your daughter will play with such a house much longer than dad or grandfather built it.

A piggy bank of creative ideas

Every girl dreams of having a real dollhouse in her room. Buying such a design in a store is easier, but not cheaper. Moreover, the quality of many toys lately leaves much to be desired. If you are going to make a dollhouse with your own hands, you will need drawings to cut out individual parts.

Plywood - universal material. It is durable, ergonomic, has an acceptable price range, and it is a pleasure for the master to work with it. You can come up with a unique plywood dollhouse. Drawings are easy to find in global network. Fortunately, progress has provided us with such opportunities.

Here are some ideas for building a dollhouse:

simple sketch;

complicated version;

New Year's dollhouse.

The complexity of the structure being built depends on your skills and abilities. First, all the parts are cut out of plywood and then assembled together. A dollhouse can be small or human-sized.

Take care to cut out doors and windows. Children can be involved in the design process. They will be able to decorate the dollhouse at their discretion. Your imagination also plays an important role. Housing for dolls can become a smaller copy of a real house with stairs, a bathroom, a bedroom, a living room, a nursery and furniture. Try it, it's very interesting and exciting.

Let's give a gift to the little princess

Things made with your own hands are always more valuable. If you decide to give a gift to your daughter, try constructing a dollhouse out of plywood with your own hands. Step-by-step instruction will be for you visual aid. Start by making a drawing. After taking all measurements, calculate required quantity plywood. Go to the store and buy everything you need.

One side of the house, the façade, is always open. It should be comfortable for the child to play with such a design. If you want to make an exclusive dollhouse, think through everything down to the smallest detail, including the decor, and also equip it with lighting.

Necessary materials:

drawing;
plywood sheets;
electric jigsaw;
drill with various drill bits;
heavy-duty glue;
yardstick;
pencil;
ruler;
water-based or decorative paint;
brush;
self-tapping screws;
LED lamp;
power unit.

Step-by-step description of the creative process:

We start by constructing a drawing. We place all the details separately on a sheet of paper. Indicate the desired size. You can take the dimensions specified in the photo.
We transfer the drawing to plywood sheets. For convenience, we will use a ruler and a simple pencil.
After we have drawn out all the details of the future dollhouse, we begin cutting them out. You can conveniently and quickly cut out parts from plywood using an electric jigsaw.
This stage is the most critical. We carefully and very carefully measure all sizes. It’s better to measure seven times. Otherwise, the house will not turn out beautiful and even. The parts must fit together perfectly.
Let's immediately cut out all the details of the dollhouse. This is the mountain of individual pieces of plywood we ended up with.
To avoid confusion when assembling the house, we will label each detail in accordance with our drawing.
To make the house look like a real one, and for your princess to enjoy playing with such a design, we measure and cut out the doors and windows. You can't go anywhere without this.
To make it more convenient to cut small windows and doorways from plywood, first drill four points.
Now, starting from the hole, we will cut out the window and door using an electric jigsaw.
We need to decorate part of the wall of the house and the balcony. To do this, draw two parallel lines and make symmetrical points on equal segments.
Drill each point to create a through hole.
We cut the distance between the holes using an electric jigsaw. It turns out this is an original carving.
When all the details are prepared, take sandpaper and sand the plywood on all sides so that no splinters are scary for the little princess.
Now we begin the assembly in accordance with the sketch.
We treat the side sections of the plywood with wood glue, and then additionally fix them with small nails.
We make sure that the nails do not penetrate through the plywood, otherwise the baby may get hurt.
After we assemble the frame, we fix the floors on the floors. If you took the measurements correctly, these parts will fit perfectly.
The finished house can be painted with water-based or decorative paint.
After complete drying, you can start lighting the dollhouse. This requires LED bulbs. minimum power, as well as a power supply.
We connect the wires and bring the lamps out into the holes made in the plywood.
We install the power supply on the back wall of the dollhouse.
Let's not forget to install a switch so that your daughter can independently turn on and off the lights for her dolls.

Why plywood
What to pay attention to
What to pay attention to
Let's get to work
Additional functions
Let's sum it up

Apartments for dolls are often expensive and are made of plastic - a fragile material that breaks easily. The article describes how to make a toy house with your own hands.

To make a child's dream of a house for his favorite doll come true, it is not at all necessary to go to the store. You can make a cottage from your own design.

Arguments in favor of self-production

Why you should build a homemade dollhouse from plywood:

Individuality. The project will be unique.
Working together with a child. Helps strengthen family relationships.

Development of creative abilities, skills, motor skills, acquisition of new experiences by children.
Possibility to create a house of any size.

Why plywood

A doll's house is made from different materials. The best option- plywood:

The use of plywood for construction ensures the strength of the future home. At good fastening parts do not fall apart or break off.
Plywood is easy to process with conventional tools.
Wooden toys are pleasant to the touch.
Beautiful appearance wood allows you to do without additional registration, surface design.
Low material cost.

What to pay attention to

Formaldehyde is used in the production of plywood. They are part of the impregnating adhesive for joining fibers. To avoid poisoning or hazardous material getting into the children's room, you need to pay attention to the markings of the sheets:

E0 - less than 6 mg of formaldehyde per 100 g of product;
E1 - 7–9 mg per 100 g;
E2 – 10–20 mg per 100 g.

Furniture and its components must be made from the safest class of plywood - E0.

How to do

Making a house for dolls from plywood is a multi-step process. A certain sequence of actions must be followed. To make the work easier, you can use step-by-step instructions.

Stage 1. Sketch preparation

The diagram should show the layout, floor dimensions in length, width, height.

You can find a sketch on the Internet and adjust it. The photo shows several basic diagrams of a toy home.

The most important thing is to maintain the proportions of the sizes to scale. This is necessary in case you want to change the dimensions of the product during operation.

The design can be thought out in advance in order to purchase and prepare necessary materials for decoration.

Stage 2. Preparing accessories and tools

For assembly you will need:

Plywood. To determine its quantity, use a drawing: calculate the number of parts, their sizes, and obtain the total surface area. Based on the result, purchase the required number of sheets. For a tabletop house you will need 2–3 blanks; for a large mansion it may take up to 7–10 sheets of plywood.
Corrugated cardboard for the roof.
Tool for cutting wood. It is recommended to use an electric jigsaw. It will help you quickly and accurately cut out parts required forms, dimensions.
Wood glue for fixing assembly elements.
Assembly tape how to aid for fastening parts.
Fine sandpaper.
Tape measure, ruler, pencil for marking.

For registration you will need:

PVA or silicate glue.
Wallpaper, color films.
Self-adhesive film to imitate flooring.
Colored cardboard or paper for decorating individual elements of the premises (optional).

Stage 3. Image transfer

To assemble wooden parts into a single whole, they must be cut from a blank sheet. To do this, scale sketches are transferred to paper, finished parts are cut out of it, and later used as a template.

If the windows are not indicated on the diagrams, they are drawn when transferring the patterns. At the house flat look Without the front wall, cuts for windows are not needed.

Stage 4. Assembly

Step-by-step assembly instructions:

The parts transferred to the plywood are cut out with an electric jigsaw. They try to do this carefully, without going beyond the contour lines: if there is a mistake, the structures may connect incorrectly.
Sand the edges to make the parts safe and avoid injury.

Cutting and finishing of edges should be done by an adult.

Assembly begins with unification internal space. To vertical end walls with glue and mounting tape attach ceilings and internal partitions according to the diagram. To strengthen the connection, the inner corners are glued with thin slats. They will add rigidity to the structure. At this stage, the child may be involved in the work.
Flights of stairs are made of wooden rulers. They are placed in the form of slides or cut one and glued together into a real staircase.

Attach the back wall.
Assembling the roof. You can cut out whole slopes from cardboard and glue them together. Another option is to assemble the roof from individual pieces in the form of tiles.

The finished frame of the house is left for several days until the glue dries and the structure acquires sufficient strength.

After assembly, the design begins.

Stage 5. Design

The finished frame is decorated and furnished with doll accessories. Recommendations:

The floor can be left as is or decorated. Plywood has a wood pattern, so covering it with a similar pattern is impractical.
You can make hinged windows and doors. To do this, attach the canvases to pieces of cardboard or use small metal door hinges. The passages are covered with fabric curtains. Windows are sometimes replaced with cardboard shutters.
The ceiling and walls can be covered with colored films, wallpaper, or painted.
Furniture for toys is placed in the rooms.

Additional functions

Not only the aesthetic, but also the practical side of the house is important: toys need to be stored somewhere, accessories need to be put away, something needs to be hidden. You can make additional built-in drawers in the upper or lower tier. This is appropriate if the house is large and takes up significant space in the living space.

Boxes are also made from plywood. The drawing provides space for storing things. The sides of the box are cut out of plywood and glued together. Screw the handle and insert it into the compartment.

You can make a hinged door like in the photo. To do this, the cut canvas is screwed onto metal loops.

Conclusion

A do-it-yourself plywood toy house will become a good gift for any child.

The construction process will take 2–3 days, taking into account the preparation of blanks, their cutting, and drying of glue. The child can decorate the premises independently.