LED lighting in the interior, options, photos. LED strip in the interior of the room Design of a room with LED lighting

Currently, there are many different ways to decorate the ceiling. Most often, owners turn to decoration ceilings LED strip. With this addition, the interior transforms and becomes more harmonious.

Today we will talk about how to choose the right lighting for the ceiling and how to install it correctly.

photos

What it is?

First you need to understand what an LED strip is. This is a flexible strip, the width of which can be 5-50 mm. On one of its sides there are LED resistors, which are connected to each other by electrical conductors, forming a single circuit. On the other side, as a rule, there is double-sided tape. With its help, the tape is fixed on one or another basis.

Different LED strips have different numbers of LEDs. In addition, they may have various sizes. To obtain brighter and more saturated light, one or two more rows of LEDs are often soldered.

Features and Benefits

In stores you can also find the most durable moisture-resistant tapes. They are not afraid of dampness and moisture, so they are often installed in bathrooms. Devices classified as IP68 can be installed underwater. Thanks to these features, these light bulbs can be found in swimming pools, landscape compositions, as well as on the facades of various buildings.

The popularity of LED strips is due to many positive qualities which are characteristic of them.

Let's take a closer look at them:

Many consumers choose LED strips for ceiling decoration because they are affordable, but do not consume a lot of electricity.
LED strips are distinguished by bright and rich light, especially if they have many bulbs. Of course, if you want to achieve a more subdued light, then you can choose options that have fewer of these components.
Such lighting fixtures are installed quickly and easily.
LED strips can have a variety of colors. You can choose the best option for any interior.

Such devices are absolutely safe, as they are not subject to overheating. In addition, LED strips do not damage ceiling bases. This quality is especially important if the room has fashionable stretch ceilings.
These lighting devices are not afraid of power surges. In such cases, ordinary light bulbs can burst, leaving behind many small fragments. There will be no such problems with LED strips.
Typically, LED strip lights are customizable. For example, you can independently change the lighting intensity. Such devices most often contain built-in sensors and special regulators that allow you to adjust the tapes to your needs.
LED light bulbs are long lasting. They can last more than 10 years.

Such lighting fixtures can complement the ceilings not only in the bedroom or living room, but also in the bathroom.
LED strips are very light in weight, so they do not put any stress on the ceiling finish.
These lighting devices are flexible and bend easily enough, so they can frame any ceiling base.
LED strips are environmentally friendly. The light bulbs in such devices do not emit harmful substances.
In addition, the tape can have absolutely any length. You can adjust it yourself.
Strips with LED bulbs do not have any effect on TV signals and do not cause interference.

Kinds

Currently, there are strip lighting devices with different types of lamps.

Tricolor

Typically these options are called RGB strips. Each diode in them is assembly of red, blue and green LEDs. These diode strips are equipped with 4 outputs. One of them is general, and the rest are intended separately for each color. From the combination of these colors you can get a rich shade range. In a similar way, a variety of colors can be achieved on a TV screen. It is worth considering that three-color diode strips need to be controlled. A special controller is suitable for this.

Using a controller, you can regulate the speed of changing colors or set one fixed color. In such a feed it is not at all necessary to launch multi-color options. You can get by with plain white.

Today in stores you can find more high-tech varieties of diode strips that are equipped with built-in Wi-fi. It is convenient to control such lighting devices using a smartphone with the appropriate application.

Strips with RGB lamps can withstand supply voltages of 12 and 24 V. You should pay attention to these values when choosing a power supply. In such models, the controller can control several devices at once, but the unit voltage must match the voltage of only one specific tape.

Sealed

Such strips with diodes are very popular today, as they are durable and resistant to wear. Otherwise they are called waterproof or waterproof. For an example of such a tape, consider the 3528 120LED-24V IP65 device. Judging by the markings, such a light strip is made on the basis of SMD3528 light bulbs with the number of LEDs 120 per meter. The sealing of these devices is achieved using a silicone shell, securely framing the part on all sides.

Sealed options can work smoothly in conditions open air and even in water. These devices are used to illuminate aquariums and swimming pools. When choosing such LED strips, you should pay attention to their markings.

Power

One of the most important parameters LED strips are their power and placement density. The most popular are devices with 60-120 diodes per meter. However, there are also other strips that have 30, 72, 90, 240 light bulbs - they can be arranged either in several even rows or linearly.

In addition, the power of one meter of strip depends on the type of LEDs installed:

SMD 3528(60 LEDs per meter) – 4.8 W;
SMD 3528(120 LEDs per meter) – 9.6 W;

SMD 3528(240 LEDs per meter) – 19.2 W;
SMD 5050(30 LEDs per meter) – 7.2 W;
SMD 5050(60 LEDs per meter) – 15 W;
SMD 5050(120 LEDs per meter) – 25 W.

Today in stores you can find tapes with a power of 220 V. They do not need standard 12V power supplies. All that is required is a small rectifier through which they will be connected directly to the outlet.

Protection class

LED strips are also divided by protection class. This parameter affects the moisture resistance of the lamps, as well as their resistance to dust and other external factors. As a rule, the protection class of the device is indicated on the packaging and is designated by the letters IP.

IP20– These diode lamps are designed for indoor use. They do not have additional sealing.

IP65– these types of flexible diode strips can be used to illuminate areas that are regularly in contact with water. For example, this could be an apron in the kitchen, a sink or an aquarium. Such devices can be installed not only indoors, but also outdoors.

IP 68– such lighting fixtures are completely insulated. They can even be placed underwater.

Features of choice

Today, many buyers purchase LED strips for ceiling decoration.

They should be selected based on the following criteria:

LED colors. Suitable shade The use of such a device depends on the task set by the owners. Using an LED strip, you can highlight some decorative element on the ceiling or simply decorate the ceiling around the perimeter.
Brightness level. This parameter directly depends on the size of the semiconductors, as well as their quantity in the tape. The more LEDs on the device, the brighter the glow it will have.

Degree of protection. IN in this case You should pay attention to the degree of protection of the flexible tape from dust and moisture. As a rule, the device class is indicated directly on the packaging.
Controller. Buy high-quality and easy-to-use tapes with controllers. Using this device, you can independently change the brightness of the lighting, as well as its hue.

Backlight options

You can create beautiful ceiling lighting with LED strip different ways:

Spot. With this lighting option, the devices are positioned in such a way as to emit light directly downwards. The most popular and well-known option for spot lighting is the “starry sky”.
Directed. With this lighting option, the tape is placed in a special way on slopes. Thanks to this location, the devices shine along the ceiling.

Absent-minded. Otherwise, this lighting option is called contour lighting. When used, LEDs form a single light strip on the ceiling base.
Figured. In this case, the devices are installed in special lampshades small size. Thanks to this solution, you can create almost any lighting configuration.

Before attaching the LED strip to the ceiling base, you need to determine its location. Consider in advance whether protrusions will be made in the plasterboard box.

Most types of LED strips are equipped with an adhesive layer. With its help, these lighting fixtures can be glued to almost any surface. However, before attaching the tape, it is necessary to carefully prepare the base and clean it of dust, dirt and other similar elements. Such actions will ensure more reliable and high-quality adhesion of the adhesive side of the device to the ceiling.

To glue the LED strip, you need to remove protective film on the adhesive side, and then place the device on the base and press. Don't press too hard. Such devices must be mounted carefully.

The LED strip can also be glued to the ceiling base using double-sided tape.

Most often, such lighting fixtures are installed in pre-prepared niches made of plasterboard sheets. Typically, the tapes are laid under the surface of these materials.

Ensembles in which the tape with diodes is attached to the curtains of the curtains or to protruding decorative elements look interesting. These devices should be installed in such a way as to direct the flow of light onto a wall or a certain area of the ceiling.

The diode strip can be hidden under the ceiling plinth. In such cases, it will not be conspicuous and seem intrusive. Its light will neatly “peek out” from under the lining, making the interior more interesting.

How to connect correctly?

After correct installation You can easily connect the LED strip with your own hands.

As a rule, this type of lighting consists of the following important elements:

power supply;
controller and sensor:
control panel;
semiconductor lighting system of the required length.

If you have securely fastened the LED strip, then you can proceed directly to connecting it.

Let's look at this process step by step:

First you need to connect to the power supply network cable with a fork.
Then you need to connect 2 contacts belonging to the controller to the block. This action should be performed if the lighting will be an RGB system.
Now you will need to connect the contact cables to the controller.

There are times when a room already has one controller installed, designed for a strip of one length or another, but it needs to be adjusted to fit larger number LEDs. In such situations, it is recommended to install an additional amplifier.

Many users are interested in how to do the wiring then. You will need to connect the power supply to the amplifier and the other end of the LED structure. On the opposite side, to reduce the load, another piece of the light strip should be fixed.

Along all connections polarity must be observed. In addition, you should monitor the compliance of the voltage of the controller itself and the power supply with the lighting device.

As a rule, LED strips are sold in small 5 m reels. If you need shorter strips, you can simply take scissors and cut off the excess part of the strip. The incision must be made in the designated place. If you are going to solder an LED strip, then you should stock up on a low-power soldering iron.

Also, to increase the length of decorative lighting, you can use special connectors for this. They are small devices that are designed to complete an electrical circuit with an easy click.

If you decide to add an LED strip to the ceiling in one of the rooms, then you should take into account some of the tips and recommendations of experts:

For the eyes, a color with a temperature of 2700-3000K is more comfortable. In terms of their spectrum, such sources are closer to simple lamps incandescent rather than daylight.
Keep in mind that one LED can have different luminosity, which depends on the voltage applied to it. However, we must not forget that as voltage increases, energy consumption also increases.
LED strip can also be used as the main lighting device in a room. To do this, you should purchase more bright options with remote control.

With the advent of LED lighting fixtures, many designers looked at the process of organizing lighting from a completely different, more interesting side. Today, home lighting work can easily be classified as creative and labor-intensive. After all, every day new ideas and opportunities for organizing a truly unique light picture appear. As a rule, several types of lighting devices are used, which together create a unique, enchanting play of light and shadow. One of the sought-after elements that no one can do without modern design, is . The scope of application of diodes is so wide that you can even find LED grass for a lawn on the Internet. However, we will devote this article using LED strip in the interior, we will share interesting ideas and tips, and also consider how to correctly and, most importantly, securely attach it to the desired surface and avoid common mistakes when installing it yourself.

LED strip in the interior

Within even the most, there will definitely be a suitable place to place an LED strip, not to mention spacious private mansions... Those who have already personally tried all the delights of using this decorative element are unlikely to be able to deny themselves the pleasure illuminate literally with her help all possible corners. Having seen enough stunning pictures on the Internet, where the tape not only helps to create bizarre illusions, but also performs a practical function, you instantly want to implement what you see in your home. In addition to the fact that diode strip is beautiful and stylish, it is also:

Concerning shortcomings using LED strips, then, perhaps, there is only one way - reducing the brightness of the diodes after a certain number of hours. Now about the ideas themselves regarding the use of tape in the interior.

LED strip in the hallway interior

The hallway in ordinary apartment buildings is most often a rather narrow and long space, absolutely devoid of a source natural light. Therefore, it is very important to make it bright and uniform, leaving no corner unattended. A good idea would be to use LED spotlights on the ceiling in combination with a tape that will make lighting different level And diverse. Thanks to this approach, the room will visually seem more spacious, not so cramped and uncomfortable.

In the hall suitable place for attaching tape will:

Doorway. This technique is very interesting, but it is not often found in, especially if the repair was carried out without drawing up a design project by a specialist. Therefore, if you want your hallway to let guests know from the threshold that the owners of the house are creative and extraordinary people, be sure to take note of this idea. There are several options for designing a portal. You can only attach the tape above the door. Can be decorated side walls opening, or you can decorate the entire door frame completely. The main thing is not too bright - with fewer diodes and a larger step between them. This is necessary so that the person entering the apartment is not blinded. The lighting should be soft and dim. To achieve this effect it is necessary to use special aluminum profiles. Their cover is made of opaque plastic and is a diffusing element;
If your hallway is not cluttered big amount furniture, it is advisable to perform above-floor lighting. That is, use skirting boards specially designed for such purposes. On their front part there is a groove into which the tape is glued, and which is then closed with a special transparent strip. The design is almost the same as a regular one. By the way, if you decide to simply glue the tape to an MDF baseboard or to a regular plastic skirting board in the place where they are screwed in and do not cover the recess with a bar, then immediately abandon this idea. Firstly, an uncovered tape will quickly become covered with dust, which can lead to its burnout. Secondly, due to the lack of a protective strip, it will be very problematic to carry out wet cleaning;
If there is a corridor on the walls, then by placing lighting inside along the entire perimeter, you will visually deepen these elements. For added effect, you can stick it on back wall mirror panel. A composition of several niches that are illuminated with multi-colored ribbon will look very beautiful. The interior of such a room will immediately become more multifaceted and dynamic;
Very often over front door or above the door that leads to the kitchen, from the hallway side there are mezzanine. We all actively use such places to store items that we very rarely use. Naturally, the builders did not think about the fact that in such a place it would not hurt to have a lamp, which will be the LED strip. It is bright enough to illuminate the farthest corners of the mezzanine and, most importantly, does not take up useful space. And if you equip the structure with a sensor that will trigger when the doors open, using such a lighting system will become much more convenient;
Between the hallway and the kitchen there is often a space that needs high-quality lighting no less than the mezzanine. You can attach the tape around the perimeter of the pantry doors with inside, directing its light onto the shelves and their lower plane;
Another useful way to use the tape is to install it in a shoe cabinet. After all, even when the overhead lighting is turned on, not the entire internal cavity of these pieces of furniture is illuminated to the required extent.

When it comes to the above methods of using tape in the interior, it is very important to connect it independently. That is, each element must be able to turn on and work separately, and not together with the main lighting. In this case, it will be possible to make the interior both bright and functional.

Living room with modern lighting

, both spacious and requires special attention.

Such zoning can be used not only in living rooms, but also in other combined rooms. Also in the living room, LED strip is actively used for highlighting certain elements. For example:

TV area lighting, namely the TV itself, began to be used not so long ago, but instantly won many fans. The diode strip is attached to the back surface of the TV screen as close to the edges as possible. Thanks to this, the glow covers a large area on the wall to which the TV is mounted. Such lighting looks especially impressive in cases where colored tape is used or when the wall has a textured pattern. Each unevenness instantly becomes more pronounced and noticeable;
Using diode strip warm yellow color you can easily imitate the light from a fire in a fireplace made with your own hands. - the pleasure is not cheap. Therefore, more and more often you can find them in the interior, which can only vaguely resemble the portal itself. Even such a small similarity is enough to bring a little warmth and comfort into the interior. Often candles are placed in the area where wood should be burned. This method is not entirely safe. Therefore, it is better to highlight the firebox with tape, but so that it is not visible. The effect will be what you need!;
A favorite element of all interiors in or in a mixed style - a wall, whether lined with another type of stone, simply cannot do without additional lighting. After all, it is with its help that it will be possible to emphasize the contour of each individual pebble and make the wall “alive”. The tape can be placed either under the ceiling or. And it’s possible both here and there. The difference between a wall with and without lighting is colossal;
If you love painting and prefer use paintings to decorate the interior, be sure to take care to present them in the most advantageous light and pay attention to them. Special picture lights certainly look stylish and perform their function well, but the cost can sometimes put them off. You can get by with regular diode tape, gluing it along the contour on the back side of the picture, as is the case with a TV. The light will not be in your eyes when one of your guests wants to admire the work of art, but will be bright enough and noticeable;
An interesting effect can be achieved by highlighting. Moreover, the tape can be glued both to their lower plane and to the upper one, or along the perimeter. The main thing is to place the light source close to the wall so that the light is softly projected onto it. Such shelves themselves will act as decorative elements, so it’s not worth piling them up with various vases and other little things. One or two items - no more. Better yet, put your favorite photos in glass frames;
Many of us love books very much and can even boast of having our own, albeit small, home library. Most often, books are placed on an open shelf. This element itself is very rich, as it is replete with a variety of colorful bindings. In this regard, designers recommend using decorative items in rooms where there are such shelving to a minimum, or even abandoning them altogether. It is much better to add the finishing touch by adding lighting to the shelves with books. The tape can be used both monochrome and color. You can highlight sections in different colors in in a certain order– checkerboard, diagonally, vertically, etc. In general, rely on your imagination;
It is impossible not to mention window illumination, namely . The tape is positioned so that the diodes point down. If you wish, you can glue the tape both in front and behind the curtains. Depending on this, you will get different glow intensities. When lighting in front of the curtains, you can further emphasize their beautiful texture; do not forget about this and do not miss the opportunity to add luxury with the help of expensive textiles;
Illuminating the sofa will create the effect that the furniture is floating above the floor. Especially if the pieces of furniture are low and down to earth. The lighting on the sofa can be placed either behind its back so that the light falls on the wall or on the bottom of the base. If you decide to highlight coffee table with a glass tabletop, remember that by placing the strip with the diodes down, you will make its back part visible. This can ruin the aesthetic appearance of the countertop. Therefore, it is better to install the tape on opaque areas;
Like the hallway, lighting the wall niches in the living room will be very good idea. In addition, if the doorway in the room is made in the form, you can safely decorate it with ribbon, thereby drawing attention to its graceful curves;
Can be supplemented with soft lighting, which are an integral element of the living room. Just do not glue the tape along the column post under any circumstances. It is better to place it at the very top under the ceiling around the column;
Various wall curves, decorative protrusions or geometric elements will look much more expressive and deeper with additional lighting;
Multi-level apartments or living rooms in private houses have an element such as a staircase. And for you it should be a wonderful canvas for creativity. in a variety of ways. It is worth noting that this not only looks impressive, but also reduces the risk of injury. The main thing is to position the tape in such a way that when you look at the steps, its light does not blind you, but only creates a soft backlight and shows the way. Choose different colors, matching them with the color of the surrounding walls or the covering of the steps. Decorate the railings, the ends of the steps or lay tape in special skirting boards, in general - go for it!;
Can't be ignored ceiling vault lighting A. In this case, there are a lot of options for placing the tape. The effect you get in the end depends on this. We'll talk about how to attach the tape to the ceiling a little later.

Do not use all methods at the same time. A maximum of two or three ideas within a spacious room, and no more than two in the interior of a small room.

LED strip in the interior of a children's room

This room should be very calm, decorated in warm, pleasant shades, especially if your child is overly active. Use bright lighting permissible only in play area or in the area where developmental classes take place.

Ideas for using tape in the bedroom interior

Just like a child's room, a bedroom is primarily a place for rest, relaxation and peace. Excessively bright light will irritate the nervous system and provoke its activity. Therefore LED backlight must be used With caution.

The picture that is one of the first to appear after the request “LED strip in the bedroom” is one, the bottom of which is decorated with a strip. So why not? Especially if your room is decorated in . Even if the bed is not equipped with mirror panels around the perimeter or does not have a special design that creates the effect that it is hanging in the air, the floating effect will still be achieved. Plus to everything - this additional source light, soft and pleasant;
Tape can be used instead wall lamps, placing it at the head of the bed. Especially if the bed is installed in a specially designed niche. The reading process will be very comfortable. And energy consumption is economical;
The dressing table must have a bright light source, which will allow you not to miss a single detail while getting ready. Diode tape can be glued around the perimeter of the mirror;
Illuminating the cornice will help create a source of soft light;
If the bedroom is adjacent to a balcony or loggia, which in principle do not need bright lighting, it is advisable to use diode strip to illuminate them. And when you need to create an intimate atmosphere in the bedroom, you can turn on the lights only there and close the curtains;
Majority modern interiors can't do without. To illuminate each section, you can also use an LED strip.

Bathroom lighting

This room is for sure. That is why the right decision will not only be used finishing materials in light colors, but also filling it with enough light. It is important to choose the right light temperature. Cool white is not suitable for these purposes. Only neutral or, as a last resort, warm spectrum. So where It is appropriate to use tape:

Of course, gluing the tape on will be not only beautiful, but also rational. It’s not for nothing that mirrors with built-in LED lighting are sold. Their cost is sometimes simply unjustified, so it is much more economical to use our idea. The tape can be placed both around the perimeter and only on the side or on the top and bottom edges. In any case, it will be convenient for you to apply makeup and perform other procedures;
It looks very interesting around the perimeter of the floor. Such a soft glow will be comfortable for the eyes even at night and will slightly expand the space;
The same can be said about lighting the ceiling in the bathroom;
Recently, it has become very popular to use lighting for various plumbing fixtures. And we are talking not only about illuminating the bathroom, which is located on the protective screen, but also about illuminating the sink by gluing tape to its lower surface around the perimeter, as well as illuminating the toilet. Whether it’s beautiful or not – judge for yourself from the photo;
It will definitely look impressive if wall-mounted plumbing fixtures are used;
It’s just a sin not to decorate in this way. The soaring effect will be achieved to the maximum;
You can also highlight wall shelves, If there are any.

When organizing lighting in the bathroom using LED strip, do not forget that this is a room with high humidity. This means that the tape must have the appropriate protection class. And again, don’t try to use all the ideas within this modest space at once.

Using LED strip in the kitchen interior

In this case, both decorative and practical aspects of using tape are most fully combined. The most popular places for its installation are:

The leading position should definitely be given with the help of the tape. In this case, it is also worth using waterproof varieties. You can stick it both to the bottom plane of wall cabinets and to the wall using special profiles. An interesting effect can be achieved if the kitchen apron is backlit;
Each kitchen cabinet, both wall-mounted and pull-out, can also be made more convenient to use if sufficient lighting is provided. You can equip the system with sensors that respond to opening;
If indoors in special

How to properly attach LED strip to various surfaces

After we have looked at so many beautiful and practical ideas When using tape, you need to make sure that your backlight simply does not come off the surface after a few days. There are not many mounting options:

Almost all tape is equipped with an adhesive layer. This has been taken care of. In order to glue it to the desired plane, it is enough to separate the protective layer by a few centimeters, gently press the tape, and then gradually advance to the end. With such installation, it is very important to properly prepare the surface - remove dirt, degrease, wipe dry and immediately begin gluing before dust accumulates. You can use the “original” sticky layer only once. Therefore, carefully think about the location of the tape in advance. The second time it just won't stick. In principle, this method allows the tape to stick even on rough surfaces;
But often the above method is short-lived and the tape begins to come off over time and simply falls off under its own weight. This is either due to the fact that the surface was not prepared properly, or the sticky layer itself was not very good. good quality. Sometimes the reason may be incorrect storage conditions for the tape by the seller. If it has been lying in a cold warehouse for a long time, even the highest quality adhesive tape will lose its properties. You just need to use new tape, which is first glued to the tape. It is better to use products that are marked “ZM” and purchase them from trusted sellers, since there are many fakes;
If the tape is long and has additional moisture-resistant protection, it is more likely to come off. For reliable fixation, you can use superglue in the form of a gel, which is applied pointwise at intervals of 3-5 cm. The rest of the space will fit tightly to the plane using the original sticky layer;
If aesthetics are not important, you can use clamps to secure the tape;
Most reliable way fixation - the use of aluminum profiles, which can be mortise, overhead or corner. This allows you to mount the tape in any place;
If you are installing a powerful tape, you must first glue foil tape to the surface, which will serve as a screen for heat removal, just like aluminum profiles. That's why you can't use regular skirting boards to place LED strips in them. It will simply warm itself;
Installation on . This is one way to secure ceiling lights. The pictures below show the diagrams correct location each element.
You can also perform hidden lighting of the stretch ceiling. The effect will be simply amazing. To do this, you need to attach the tape using special brackets from the plane of the main ceiling, and then pull it PVC film. Position the tape so that it forms a specific pattern.

Typical installation errors

It is quite difficult to install a diode strip incorrectly, however, there are such unconventional mounting methods that are best avoided:

Until recently, room lighting was limited to a chandelier, wall sconces, and floor lamps. Today, designers have a unique opportunity to enliven and diversify residential and office spaces using LED strip in the interior.

It is used both as a main and additional lighting premises, creating a cozy and warm atmosphere. At the same time, complete safety is guaranteed when using such lighting, the absence of harmful and irritating flicker, and energy savings.

What is LED strip?

An LED is a semiconductor device that emits light when electricity passes through it. The LED strip is quite thin and flexible. In specialized stores they sell it in rolls. The LED beam angle is 120°.

On the reverse side, almost all tapes have an adhesive backing, which simplifies installation. There are tapes in which fastening is provided with clips, which is also convenient during installation.

Colors

An important parameter in an LED product is color shade glow. Ribbons can be divided into two groups: multi-color and single-color. When voltage is applied, single-color tapes emit one color: white, red, blue, green or yellow. There are products with a turquoise, crimson, and purple glow.

White LED strips, in turn, are divided into subgroups according to color temperature (cold, neutral or warm). Non-standard options include products with infrared and ultraviolet luminescence.

Multi-color tapes are produced using multi-chip LEDs, each crystal in them emits specific color. The most common are strips based on RGBW and RGB LEDs. The designation in English letters indicates the color of the glow: B - blue, G - green, R - red, W - white.

LED strips are connected through a controller that regulates the power supply of the color channels. Today, manufacturers produce regular and moisture-resistant LED strips, which are successfully used in wet areas: They even decorate Jacuzzis and swimming pools.

Where is the tape used?

The good thing about LED strip in the interior is that it can be used in any room. Thanks to its flexibility, designers successfully use it to illuminate niches, cabinets, and any areas of the room that need to be highlighted and emphasized.

The safety of this material allows the use of LED strip in the interior of a nursery. Parents do not have to worry that the baby will turn over the floor lamp or drop the table lamp. In addition, such a tape can be attached at a height inaccessible to the small owner.

LED strip in the interior goes well with traditional lighting sources - there is no need to abandon the spotlights and chandeliers that we are so accustomed to. Despite the fact that the brightness of the tape is sufficient to illuminate small room, it is often used as an elegant touch, an additional accent. Often with the help of such an original lamp they emphasize beautiful designs in the room. The flexible, bright tape will accurately follow the contours of any surface: it can be bent and cut so that not a single corner is left in the dark.

LED strips for illumination

Imagine this situation: you thought it through and made it on the ceiling original design, which was decorated with patterned wallpaper or a fresco. But when turned on there is a blurry spot. In this case, an LED strip will help you: stick it around the perimeter of the recess. In the same way you can decorate a relaxation corner and furniture. At the touch of a button, your relaxation area turns into a shimmering disco room.

Along with the LED strip for illumination, we recommend purchasing a device that regulates the brightness of the lamp - a dimmer. This will allow you to create settings for slow fade and dimming modes, and will allow you to automatically turn off at right time lighting.

Stretch ceiling

Stretch ceiling structures are becoming more and more popular in residential premises every year. The decor of such coatings is carried out using various lighting. One of the most popular of them is LED strip. Installing it under a suspended ceiling or inside a structure depends only on the preferences of the homeowners.

Installation of LED strip under a suspended ceiling is possible for any design. And if such lighting is located behind tension fabric, inside the structure, you will have to choose a special type of fabric - light transmitting. In addition, in this case, certain requirements must be met. First of all, this concerns the distance from the tape to the stretched fabric: it must be at least ten centimeters.

Consider the place where the transformer will be located (if the backlight is multi-colored) and the control unit. They do not take up much space, but the blocks should be freely accessible.

Bedroom

LED strips in the bedroom interior are most often used as an additional option. A cozy atmosphere in this room will be created by colored LEDs for walls, mirrors, paintings, photos, and for ceiling lighting. The lighting colors for the bedroom can be any - it all depends on the personal preferences of the homeowners. With the help of such tapes you can highlight furniture in an original way and inner part cabinets

LED strip for the kitchen

In the kitchen, such lighting not only decorates and transforms the interior, but is also practical. Here the tape is fully used for lighting work surface and cabinets. The LED strip for the kitchen looks interesting and unusual on the lower (in this case the floor is illuminated), as well as on the upper parts of the cabinets. As a rule, floor-standing cabinets are installed on legs, which are covered with a panel at the end of installation or can be left open. A glow strip attaches to the bottom of the cabinet and illuminates the floor. For such lighting, you should use a sealed tape, since moisture can get into it, for example, during cleaning.

To highlight the top of the cabinets, you can also use open tape, since it is not exposed to any external influences. The use of LED strip in the kitchen is not limited to illuminating the space above and below cabinets, but is also successfully used to illuminate their interior, which, you see, is very convenient.

The interior lighting of cabinets can be connected so that it turns on simultaneously with the kitchen lighting, or it can be used with special sensors that respond to door opening or touch. There are also contactless ones - you can turn them on if you hold your hand next to them. This is very convenient when, for example, your hands are wet. Even more important is the lighting of the work surface. Housewives know how inconvenient it is when there is a light source behind your back when cooking. In this case, LED lighting is installed under wall cabinets. It is important that the LED strip is positioned in such a way that the light falls at an angle or straight down and does not hit the owner’s eyes.

Stairs

LED lighting of stair steps in two-story house or apartment is not only very beautiful - it also ensures the safety of the household. To do this, you can use both single-color and multi-colored ribbons, which will enrich the interior. The LED strip does not require any skills to install - anyone can cope with this task. In addition, such lighting can be installed many times, which allows you to change the space at any time convenient for you. And one more important fact: the cost of this material is quite affordable, and the service life of such a tape is about ten years, which makes such a purchase very profitable.

The possibilities for using LED strips are enormous: they can illuminate the kitchen work area, highlight the interior, and create a romantic or festive atmosphere. Self-adhesive LED strips allow you to implement the most daring interior lighting solutions.

How to choose a suitable LED strip? Let's figure out what types of LED strips exist. There are several parameters in which they differ, and each of them is reflected in the labeling.

Glow colors

They are marked with the first letter of the color name in English, which stands immediately after the abbreviation LED and before the letters SMD (designation of element type).

Based on the color of the tape, they are divided into:

The most common sizes are 3528 with dimensions of 3.5 by 2.8 millimeters and 5050 with dimensions of 5 by 5 mm. There are also other standard sizes.

Size determines how much light energy an element emits per unit time.

The larger the crystal, the more energy they can emit. The numbers for monochrome elements are:

chip size 3528 allows you to get a flow from 0.6 to 2.2 lumens;
size 5050 - 2-8 8 lumens.

Indicators for universal LEDs are below:

for 3528 – from 0.3 to 1.6 lumens;
size 5050 - from 0.6 to 2.5 lumens.

Data are given for crystals without protective coating. Its presence reduces the intensity of the meaning.

The total brightness is obtained by multiplying these numbers by the number of elements in the segment.

Number of LEDs

The density of elements per meter of tape may vary. Firstly, LEDs can be arranged in one row, or in two or more. However, the number of LEDs in a strip per meter is a multiple of the number of rows multiplied by 30. That is, in a single-row strip it is a multiple of 30, in a double-row strip it is a multiple of 60, and so on.

Degree of protection

It is marked as IP. The marking contains two numbers, the first indicates the degree of protection against ingress solids, the second - from moisture. Sometimes manufacturers use their own designations.

The tape may not have a protective sheath and is suitable for dry areas. For rooms with high humidity They produce tapes coated with moisture-proof varnish. Moisture-resistant tapes have a sealed silicone housing and can be installed in water.

LED strips placed in plastic pipe, protect well from both mechanical influences and water. The stronger the coating, the higher the numbers on the marking (up to IP65 – IP68).

It is also worth remembering that the additional shell increases both the price of the product and the degree of overheating (silicone does not remove heat well).

Supply voltage and power

The supply voltage required for the tape is indicated by a separate number on the label. Most often it is 12V, sometimes 24V. To connect, you need voltage converters from the general network.

Converter power is calculated based on power consumption linear meter tape, which can be found on the packaging. You can calculate it yourself.

The choice of LED strip for the interior is determined by what functions you want to assign to it. Photos of various LED strips in the interior, many of which are available on the Internet, will help you understand what exactly you want from additional lighting.

White light with bluish tones will highlight the appliances in the kitchen and complement the lighting, while red ribbons will help create an intimate atmosphere.

Remember that colored light can visually distort the colors of objects. This effect is strongest for blue ribbons. Take this factor into account when selecting lighting.

Effective LED lightening looks on the ceiling ledges, and liquid wallpaper will help to disguise the tapes.

Choose your LED strip wisely and pay careful attention to its installation, and your lighting will bring you aesthetic pleasure, as well as last a long time and reliably.

Photo of LED strip

LED strips in hands experienced designer turn into a universal tool with which you can transform any interior. Contrary to popular belief, LEDs can be combined with all styles, not only high-tech; even in classics there is a place for bright and functional lighting.

Different intensities, colors, and light spectrum will allow you to hide the shortcomings of the room, make it lighter, place accents, and highlight semantic zones. Design studio "Interiorcom" as an example own works will show interesting ideas application of LED strip and will tell you how to use LEDs more effectively in a modern interior.

Kinds:

LEDs are available in the form of conventional lamps, chandeliers, lamps, sconces, spots and strips. Tape cords with round are more often used for architectural lighting of buildings and amenities. Flat LED strips are used in the interior - they are more compact and take up less space and practically do not heat up. Simple installation and great possibilities for decorative lighting make them indispensable assistants in interior design.

Lighting devices based on diodes can be used as independent lighting units, or can be combined into common system, which will be configured and managed centrally.

In the photo: LED lighting in the interior of the apartment.

Elements of the lighting system:

Interior lighting consists of several required elements:

Profile;
LED RGB strip;
Controller with sensors;
Power unit.

Therefore, it is not enough to provide a place for attaching the tape, for example, under the ceiling, or in the kitchen under cabinets; you also need to figure out where the controller with the power supply will be located, and where the wires will go out. The tape itself does not heat up much, but the control units generate quite a lot of heat, so they require good ventilation.

LED strips in the TV area in the living room. The whole project.

Different colors and intensity of glow:

The simplest and most inexpensive LED strip will always be one color. To be able to change the color of the lighting in the interior, you need to choose a GRB tape. In this case, you can specify the desired backlight shade (depending on the time of day, mood, scenario), as well as the order in which the colors change. Moreover, it is often possible not only to switch colors manually, but also to program automatic switching using special modes. You can also change the intensity of the glow, adjust the brightness, activate sleep mode, and connect additional sensors, for example, motion or sound.

The LED backlight is controlled using wall switches, dimmers, remote controls, special controllers and even through a special application on your smartphone!

LEDs in the interior of a bachelor's apartment.

Purpose of LED lighting in the interior:

Diffuse central lighting. In this case, the tapes are used as the main light source. They are evenly located along the perimeter of the ceiling, filling the entire area of the room with light. For these purposes, neutral colors and calm radiation are used;
Zoning of space. In this case, lighting acts as a delimiter, zoning inner space. Work areas are highlighted due to bright local lighting - area kitchen apron, desk in the office, etc.;
Accent lighting. Working with decorative light, which allows you to draw attention to a specific area or object placed in the room. This is how objects of art, decor, niches, pieces of furniture, etc. are illuminated;
Decorative lighting. It is used to enhance the impression of the created interior, hide the shortcomings of the room, and visually expand the boundaries of the room.

Backlight working area in the nursery in the interior of the apartment in the Svyatogor residential complex

Application options for LED strip:

In apartments and country houses LED lighting is used quite widely. In addition to classic lighting devices, strips are used for lighting:

Ceilings - suspended and plasterboard, simple and multi-level, along the perimeter and under the canvas;
Walls - in the area of the genital and ceiling plinth along the perimeter, within one wall, behind the wall;
Floors - along the perimeter, along the edges, in the area of podiums, etc.;
Furniture - upholstered and cabinet furniture, kitchen sets, work areas;
Decorative items - mirrors, paintings, niches with souvenirs, books;

Stairs - along the railings, along the lower border along the wall, in the area of the risers;
Plumbers - shower cabins, bathtubs, swimming pools, taps. LED strips combine especially well with built-in console plumbing fixtures.

Correct use of LEDs allows you to add lightness to the interior, visually expand the space, decorate and complement it.

LED strip in the bathroom in the project of this apartment.

Our company has repeatedly implemented projects using LED strip in the interior. Such solutions always turn out successful, stylish and modern! Do you dream of a cool interior? Call soon! We will help you arrange your space as correctly, conveniently and beautifully as possible!