Services	Price
window frame	prices from 4,000 rub.
Door frame	prices from 4,500 rub.
Met. tiles (without insulation)	prices from 1200 rub./m2
Met. tiles (with insulation)	prices from 1300 rub./m2
Natural tiles (with insulation)	prices from 1,600 rub./m2
Painting	90-100 rub./m2 layer
Log skin	prices from 250 rub. /m2
Installation of platbands	from 1,000 rubles side
Lining, imitation timber	350-400 rub./m2
Subfloor - plywood	250-300 rub./m2
Clean floor	300-400 rub./m2
Assembling a log house	2900-3200 RUR/m2
Sanding the exterior walls of a house	from 250 rub./m2
Treating wood with antiseptic primer	70 RUR/m2
Removing the pile manually using a sanding block 98x69 (to prevent moisture from entering through the pile)	80 RUR/m2
Grinding the end cuts at home with the application of face oil. cuts (calculation after the fact)	from 350 rub./m2

If you think that by building a house, you get your dream ready-made, then this is not so. Important place V wooden house takes up internal processing and the cost of finishing a wooden house. Our company’s craftsmen have many years of experience in finishing wooden houses and related works with this direction, they can do a lot and are able to do a lot.

What does the home you've always dreamed of look like? Usually our consciousness displays some kind of abstract picture, in which there is definitely no place for the materials from which the façade of a wooden house will be finished, and you most likely have a very poor idea of what your interior rooms in your wooden house will be like. There is currently a huge variety of products on the building materials market. In order not to get confused in independently choosing the right material, our company offers to do this for you; in order not to get confused in the order of prices, you can see the table above. And then we will carry out high-quality finishing at a low price, naturally, taking into account all the wishes of the clients. If you want to decorate your house on a professional level, then this work is divided into several parts. How much each work service will cost can be seen in the cost table.

Finish turnkey from the inside. How to create comfort with finishing?

The first thing that needs to be achieved when finishing a wooden house is to give it warmth and comfort. The interior decoration of a wooden house Moscow, buildings (houses, baths) is divided into the following parts:

Initially ready house subjected to grinding. This is the least expensive part of the work
Next install internal partitions wooden house, which will form a frame.
Afterwards, the house is insulated and the necessary waterproofing is carried out.
Ceiling finishing is usually done using lining.
The walls of a wooden house are also treated using clapboard or other material is used for this.
The floor finishes are made with laminate.

Lining is the most profitable and convenient material to decorate a cottage. In addition, the lining is environmentally friendly, it has high thermal conductivity and sound insulation. With the help of lining you can decorate both a cottage and a bathhouse. Well, there is no doubt about the pleasant appearance of the lining. You will have a pleasant time in such a bathhouse!

Our company also provides services such as coating wooden log house special protection, and we also provide painting of the building; you can place an order or see prices for these services on our website.

Turnkey finishing of the outside of a wooden house. What appearance will the house have?

Decorating the outside of a house is not only about creating a beautiful and presentable appearance, but also about protecting the building from bad weather, which happens very often.

Exterior finishing wood panels consists of the following steps:

Installation of a wooden frame. It is necessary in order to prevent distortion of the door and window openings during the shrinkage of the entire house. Typically, this service can be arranged immediately after construction is completed. Prices can be viewed on the website.
Caulk at home. This is one of the options for its insulation. As many years of practice have shown, it is the most proven option. Caulking is not only reliable, but also quite affordable, which is important for many. If you wish, you can call our company to calculate more detailed prices.
Painting and sanding houses using antiseptic solutions. Grinding combines several tasks at once. First of all, it makes the house beautiful. And also with such wall decoration, you can subsequently apply paint or varnish in an even layer. To choose the right paint, you need to take into account that the house must “breathe”. Accordingly, the price of painting a house will directly depend on the price of materials and the amount of work.
Insulate the house inside by insulating all the walls in the house
Finishing a wooden house from the outside with siding. Internal treatment of the walls of a wooden house with clapboard or other materials. Finishing baths and saunas is also usually done using lining, which is convenient and practical and at a low cost.

How to determine finishing prices?

Our company trusts only reliable suppliers of materials for affordable prices, who, thanks to long-term cooperation, provide us with a 20% discount on the cost of materials. Therefore, we can afford to significantly reduce the cost of repair work so that you can place an order at affordable prices without losing the quality of the home’s finishing. You can find out the prices in the corresponding section of our portal; there is also the price at which wooden structures and baths are finished. The final cost can be made upon request from our managers. We will create comfort in your home!

Processing a wooden structure is no less important a process than building a house as a whole. Therefore, it is recommended to pay no less attention to him. Only in this case the house will end up being priced at a price that suits you. In Moscow, finishing of a wooden house can be external and internal.

Of these two types, the cost of finishing is the external one, which is considered the most important, because... it not only fulfills its direct task - providing a beautiful view, but also performs a protective function. Therefore, it should be thought about at a time when the house exists only as a project.

Features and cost of finishing a wooden house from the outside on a turnkey basis inexpensively

The most popular finishing material is siding. The house can be made of polymer raw materials, as well as steel, copper or aluminum. The cost of finishing with siding is very low and is easy to do. Also this finish has a pleasant appearance. In addition, siding has several advantages: This finish has a long service life, it is resistant to ultraviolet radiation, as well as dust or bad weather. Another practical material used to decorate a house is lining. And in last days Special home finishings that imitate a log look are very popular among consumers. Insulation as a finish for a wooden house includes a layer of insulation, which increases its thermal insulation performance. Prices for this service can be found on the website.

It should be taken into account that external finishing of a wooden house not only changes the appearance of houses, but also completely protects it from the vagaries of nature and the impact environment. If you want a change, or the finish has become outdated or unsuitable, our finish can easily be replaced with a new one. What is definitely not advisable to use as a finishing material is plaster. In this case, the house simply will not “breathe,” which will lead to the fact that sooner or later the wood will begin to crack.

You don’t have to use any materials for exterior finishing at all. But for this it is necessary to treat the timber with a special solution. And this needs to be done once every five years, at least. Otherwise, your home may be susceptible to infestation by insects, bacteria, or mold.

Turnkey interior finishing of a wooden house

Before you begin interior finishing work, you need to treat the wood from the inside. After the log house is finished, it is thoroughly cleaned and then sanded inside. After this, the wood is coated with protective solutions, in several layers. To give maximum smoothness to the walls, they can be coated with the appropriate composition. To make a house seem made of wooden walls and inside, it is necessary to achieve this effect using a special coating that gives the appearance of pure wood. You can also apply artificial cracks and scratches for even greater aesthetics, as happens on real wood.

And after that, you can use a flight of fancy on the topic of what my house will look like inside.

If you want to achieve absolute smoothness of the walls and tint them, then you need to take into account the fact that the toner will look different depending on the type of wood. To achieve the desired shade, apply the paint with one brush, twice and in one direction. First apply a lighter tone, and then move on to a darker one. At the same time, you should not completely smooth over the natural color of the wood. You just need to emphasize it effectively. But which color to choose - smooth glossy or matte - is at your discretion.

While decorating the house, it is advisable to maintain the overall style and trend of the house. The natural shade of wood can be combined with other decorative materials that have different prices. It could be stone, ceramics, the same wood, but of a different species, etc. The flooring is usually covered with cedar or larch materials, which are the most practical in combination with a beautiful appearance.

At the same time, the floor finishing should be in harmony with the walls, otherwise a single composition will definitely not work. The floor can be tinted; this service also has its own cost. In this case, the color used is usually darker than the one used for the walls. All together this will not greatly affect prices.

It should be noted that when carrying out work, no matter internal or external, we do not recommend saving on materials, or limiting ourselves to just one stage. This approach can not only disrupt the appearance, but also affect the durability of the entire house for the worse. Quality work can be purchased at construction company"Century House", the price will pleasantly surprise you. Before placing an order with us at affordable prices, familiarize yourself with the price list of finishing costs, our consultants will tell you how our prices are formed, and you can easily make sure that with our finishing wooden houses can be made very cheaply.

13410 1 5

Self finishing timber house outside and inside

Wooden houses have always been, are, and apparently will remain for a long time perhaps the most popular buildings among private developers. Log house it is beautiful, but it is quite expensive, so most owners prefer a house made of timber. In this article I will tell you how to finish a timber house from the inside and outside, and this material is designed for those who are going to decorate the house with their own hands.

Why finish a timber house at all and when can you start work?

Most ordinary people, far from the intricacies of construction, do not understand why a wooden house might need exterior and interior decoration. After all, wood itself is a beautiful, self-sufficient material and all that can be done with it is just varnish or paint.

They are partly right, but only if we are talking about the so-called laminated veneer lumber. The construction material really very beautiful and comfortable. Such beams are glued together from several layers of well-dried and impregnated protective compounds wood

In addition, they have grooves (profiles) cut into them, which allow you to assemble the house like a construction set, by the way step-by-step instruction included with such sets. As a result, the owners receive a good-quality house without large cracks or distortions.

But the price of such a “constructor”, to put it mildly, is “biting” and therefore many people, instead of laminated veneer lumber, use ordinary, and not always well-dried, lumber. And an ordinary timber, I’ll tell you honestly, only looks good on an advertising stand in a store; as soon as you build it into the desired environmentally friendly housing, its appearance is unlikely to suit you.

Although even structures assembled from laminated veneer lumber, despite their attractive appearance, often need finishing. In order for the house to be warm, you need to either buy very thick and expensive beams, or additionally insulate the building. And here the warm finishing of the façade of a log house comes to the rescue.

We've sorted out the reasons, now let's talk about when you can start finishing work. As you know, any wooden structure shrinks over time.

If you bought a ready-made “construction set” made of laminated veneer lumber, then this indicator is minimal. IN in this case general shrinkage will continue for about 3 years, and finishing can begin in six months, maximum a year.

Monolithic, well-dried beams with cut grooves will not shrink much more, but still finishing should not begin before a year later. And in this case, such a house will need to be generously “flavored” with various kinds of protective impregnations.

The worst situation is with a simple, even beam, which at the time of construction has natural moisture. Such buildings take at least 5 to 7 years to settle. As for the beginning finishing works, then many masters advise starting them after a year, although I always recommend letting such a house stand for at least a year and a half, or better yet, 2 years.

It doesn’t matter what kind of wood you are going to build your home from, immediately after construction the box must be covered with a roof and be sure to be treated with protective impregnations, so that while shrinkage occurs the wood does not begin to deteriorate.

Existing types of finishing of a timber house

By by and large To decorate a log house, all the same materials are used that are used for cladding a brick, block or any other structure. But they need to be used selectively, because the external and internal cladding of wooden structures have their own specifics.

How to decorate a timber house
Types of cladding	Characteristics
Plaster	One of the most durable cladding methods, but in this case it is extremely important that the shrinkage processes in the house are completed, otherwise any movements of the base can cause cracks and even peeling. Plaster is more suitable for older houses.
Siding	Siding panels can be plastic, metal, cement and wood. Depending on the material, the service life of such finishing ranges from 15 to 50 years. Siding has always been considered an external cladding option; I personally have not seen it installed from the inside.
Facade facing brick	Everything here is clear from the name. If the brick is of high quality, then such cladding will last for at least 50 years. As a rule, between wooden and brick wall insulation is installed. The only limitation may be the foundation; such cladding requires a wide, permanent structure.
Natural or fake diamond	Can be used both inside and outside. Although in most cases, stone finishing of wooden buildings on the outside is limited only to the base. Plus a natural stone has a solid mass and needs to be equipped with an appropriate foundation.
Different types of lining	Lining is a universal material; it can be used everywhere. Modern planks have a tongue-and-groove connection and are installed quite simply. In our case, finishing with false timber is best suited; in fact, this cladding is one of the types of lining; in some sources it may be called a block house; for a timber house this is the best option.
Varnishing or painting	This type of wood processing can also be considered universal. But, as you understand, we are not talking about insulation here, so varnishing or painting is more often used as an interior decoration, although in the case of wooden lining such processing can also be performed on the outside.
Tile	In this case, tiles are more relevant for interior cladding of services in the house. From the outside, it can only be used to decorate the basement and porch.
Drywall	Drywall is convenient facing material, but it can only be used for interior work.

Facade cladding

Naturally, the first thing that interests home craftsmen is how to decorate the outside of a log house. Since our priority is to install the cladding with our own hands, then it is better to forget about such things as brick, plaster and natural stone right away; without experience you are unlikely to cope with such work.

All we have left is varnishing and ventilated façade technology. In this case, ventilated facade technology should be understood as the installation of siding and all types of lining. It’s not for nothing that I combined all this; the fact is that the instructions in all these cases are similar.

Before you begin finishing any wooden structure, you should once again caulk all the cracks both outside and inside the house. First, hemp or jute is pushed into the joint, and the gap is closed from above with a special sealant. By the way, this sealant was created specifically for these purposes and no other sealant will fit here.

Ventilated facade technology

In my deep conviction, for beginning craftsmen, a ventilated facade is, if not the only, then certainly one of the most acceptable options for finishing a wooden house.

This type of façade is called ventilated because a gap is left between the finishing cladding and the base, and insulation can fit into this gap. But first things first.

Since in any case the walls of the house themselves will not be visible, there is no need to clean, sand and level them; it is enough to simply caulk and seal the cracks between them. True, some masters insist on such processing, but I believe that this is unnecessary. But protective treatment in this case is mandatory, and there is no need to skimp on impregnations;
There is nothing complicated in such processing, just buy a composition for biological protection of wood (antiseptic) and a composition for fire protection (fire retardant), take a paint roller or a wide brush and apply everything in layers, while allowing each layer to dry.
Ideally, all protective compounds should be applied before the construction of the house begins, so that the timber is protected over the entire area, but if for some reason this was not done or you are finishing an old house, then you can impregnate the finished structure;

It is better to take professional impregnations with comprehensive protection, now the price for them is reasonable, homemade liquids are folk recipes are no longer relevant, plus the quality of homemade products is an order of magnitude lower.

When the impregnations have dried, wooden wall a vapor barrier membrane is attached. In general, it is pressed against the sheathing strips, but for me it’s easier to shoot it with a stapler first, so you can do without helpers. And don’t forget, steam moves from the room to the street; if you fill the membrane incorrectly, condensation will form under it (such a fabric always has marks indicating the vapor-permeable side);
Next you will need to lay the sheathing on the wall. If on block houses most often the lathing is made from metal UD and CD profiles, but for wooden walls it is better to use wooden blocks, they are much easier to work with. The thickness of such a bar must be at least 40 mm, and the width is selected according to the thickness of the insulation;

The top cut of the sheathing should be in the same plane. Even if it seems to you that your walls are smooth, it is better to be safe. The first 2 outer bars are attached to the wall, then 2 - 3 cords are pulled between them and the remaining bars of the sheathing are placed along these cords.
If the next plank protrudes beyond the cord, then it needs to be corrected with a plane, and when it does not reach the cord, a wedge is placed. The planks themselves are screwed to the wall with long self-tapping screws;
As for the step between the planks, it is considered that the thicker and stronger the finishing, the wider the step can be taken, the maximum is 70 cm. But personally, under any material, I install the lathing in steps of half a meter or along the width of the insulation;

Siding panels, as a rule, are attached to a vertical sheathing, but under the lining the sheathing should be installed perpendicular to the direction of laying the planks. The only exception is the diagonal laying of the lining; it is attached to a vertical sheathing. Although I don’t advise you to undertake diagonal installation, firstly, there is 30% more waste, and secondly, this requires experience;
As insulation for wooden structures usually mineral wool is used. The fact is that wood must breathe and it is undesirable to clog it with polystyrene foam or extruded polystyrene foam. Of course, you can take any cotton wool, but soft glass wool and the like will cake within 2 to 3 years, so it’s better to pay a little more and install dense mineral wool slabs. Now is the time high quality for basalt cotton slabs;
Thickness of cotton insulation for middle zone of our great and mighty homeland varies around 100 mm. Naturally, the further north the region is, the thicker the insulation needs to be;

When cutting cotton slabs, make the width 20 - 30 mm larger than the distance between the sheathing guides. This way your insulation will fit tightly, without gaps, between the bars.

Cotton wool cannot be left unprotected, it is afraid of humidity, so we attach the so-called wind protection on top, in fact it is the same vapor barrier;
The wind protection is fixed to the guides with a counter-lattice, but for convenience it is better to attach it first with a stapler;
The counter-lattice strips provide the same gap, plus it is on them that the finishing cladding is attached. For lining, I usually use 30x40 mm bars, there is no point in taking smaller ones, they will split from nails, but for a heavy block house or siding under a counter-lattice, it is better to take 50x50 mm bars;

Nowadays, any type of lining is installed using clamps, these are small plates with a protruding tongue. The tongue clings to the edge of the groove, and the plate is nailed or screwed to the counter-lattice;
The siding is fixed with screws with wide heads. The panels have special fastening holes, so the self-tapping screw must be driven clearly into the center of the hole and not tightened all the way, the panel on one side should hang on the screws, and the lower part clings to the groove of the previous panel.

Rules for wood varnishing

The technique of applying varnish and painting is practically no different. Initially, you will need to thoroughly sand the surface. If the laminated veneer lumber is already well processed, then you will have to tinker with the regular one.

You start processing with coarse sandpaper and gradually work your way up to fine-grained sandpaper. With such volumes, it is very difficult to do this manually, so it is better to get a grinder.

By the way, before varnishing or painting, the wood will also need to be treated with protective impregnations.

If your plans include changing the color, then the surface is treated with stain. Next, let the wood dry and apply the first coat of varnish. After it dries, no matter how well you sand the timber, the pile will inevitably rise on it and the surface will become rough.

To remove lint, use fine sandpaper. Moreover, there is no need to sand particularly hard; the lint is removed with a few light movements, after which the dust should be wiped off with a damp rag.

From experience I can say that one finishing layer of varnish is not enough, there should be at least 3 such layers, although in order to achieve a perfectly varnished surface, sometimes it is necessary to apply up to 5 - 7 layers of varnish.

After sanding, do not delay the application of varnish. In order for the wood to look decent and the varnish to adhere well, it must be applied within 3 to 4 days.

Regarding the type of varnish, I will say this. Now many people recommend acrylic varnishes on a water-dispersed basis, it is believed that the wood under them breathes, they are of course of high quality, but they are quite expensive.

Personally, I prefer to use yacht varnish (urethane-alkyd), it is durable and withstands all the vagaries of the weather well. Now the price of urethane-alkyd varnishes for exterior use starts at about 400 rubles per liter jar.

Decorating the house from the inside

It is impossible to answer briefly the question of how to decorate the inside of a timber house; it all depends on what exactly you are going to cover. Plus, the type of room plays a big role; you must admit, the decoration in the living room and in the bathroom are significantly different.

Floor and ceiling cladding

Cladding the floor and ceiling in a house made of timber are two adjacent directions, because the ceiling, in fact, is either an interfloor ceiling or a floor attic space. Therefore, it is impossible to consider them separately.

The floor itself in a wooden house can be based on floor joists or installed directly on a monolithic iron concrete slab, while the difference in finishing technology is small, but it still exists.

Solid wooden logs are a good basis for the structure. Naturally, in order for the floor to be warm, it will need to be insulated. There is a small nuance here.

If it is better to insulate the walls of a wooden house mineral wool slabs, then foam plastic is more suitable for floors and interfloor ceilings. You can, of course, buy extruded polystyrene foam, but I believe that in this particular case, ordinary PSB-S25 foam is more suitable, the effect is the same, and such foam costs at least 2 times less. I usually buy foam boards 50 mm thick.

Let's start with arranging the floor on suspended logs. After the logs have been treated with protective impregnations, you need to build a subfloor in their lower part. There are several methods here, I will tell you about the method that I use myself.

First, on the sides of the lower cut of the logs, cranial bars with a cross section of 50x50 mm are packed; they will become the base for the rough flooring. Next, planed boards with a thickness of about 20–30 mm are laid on these bars in even rows.

There will be a constant pull of moisture from the ground, so both the skull beam and the planks of the rough flooring must be well impregnated with protective compounds.

I use creosote for this; they used to impregnate railway sleepers with it. In a residential area, such impregnation is undesirable, but it is perfect for a subfloor. But this is a personal matter, you can take any impregnation you like.

The subfloor slats are cut exactly to size and laid on the skull beam; they, of course, can be nailed, but I don’t see much point in this, they won’t go anywhere anyway.

Now a continuous layer of technical polyethylene is laid over the entire room, with a sheet of technical polyethylene wrapped around the log and fixed with a stapler. It will protect from moisture, plus even if there are cracks left somewhere, there will be no air blowing through them.

Polystyrene foam itself does not allow moisture to pass through, so there is no point in installing any kind of hydro or vapor barrier on top. If there are large cracks left somewhere, don’t worry, they can be blown out with foam.

For a wooden house, the best and simplest option, in my opinion, is to install a floorboard. For this, planed tongue and groove boards with a thickness of 40 mm or more are used. In order not to spoil the appearance of nail heads on the floorboard, the planks can be fixed using clamps or hammering nails into the lower part of the groove of the board.

To install parquet, laminate and other newfangled coverings, you will need to make a durable monolithic flooring. In such cases, I sew plywood of the FK brand with a thickness of 10 - 12 mm in 2 layers, and the joints between the layers should not coincide.

Some craftsmen install OSB flooring, but I haven’t tried it, so I can’t say anything about it. The only thing I definitely don’t recommend doing is using chipboard sheets to lay out the base on the floor; at the slightest humidity they will swell and begin to peel off.

If a wooden house is built on a concrete slab, then there is less work. You need to lay overlapping concrete on the walls. plastic film. After this, install logs with a cross-section of 50x50 mm and lay foam plastic between them, and sew a finished floor on top using any of the technologies described above.

As for the ceiling, the easiest way is to hem the lining from below to the joists. On the side of the second floor or attic, cover everything with technical polyethylene, insert foam plastic between the joists and arrange the floor in the attic or on the second floor.

Both in the attic and in interfloor covering you definitely need to install some kind of sound insulator; the cheapest option is to take foam plastic, but no one is stopping you from using, for example, mineral wool or expanded clay.

Now it's fashionable to leave them open load-bearing beams on the ceiling. The depth of such a beam usually fluctuates around 200 mm. In this case, I stuff a skull beam along the entire length approximately in the middle of the beam and hem the lining to it. Next, as usual, polyethylene, insulation and finishing coating of the second floor.

There are, of course, more multi-level ceiling made of plasterboard and suspended ceiling. But installation of multi-level plasterboard structures requires some experience and stretch ceiling This is a rather expensive thing and, without having the knowledge and special tools, I do not recommend undertaking their installation at all.

Arrangement of walls from the inside

As I already said, finishing the inside of the house with false timber is a priority method, because the house, after all, is made of timber and in this case we are simply correcting visual defects in the supporting structure.

False timber is the same lining, only large sizes. In theory, if the walls are smooth, then you can sew the cladding directly onto the walls, but believe me, it is better to put sheathing on the walls and install false beams on it. In this gap you can hide electrical wiring and communications.

The cross-section of the sheathing bars depends on how much clearance you need. For arranging only electrical wiring, a 30x40 mm block is sufficient. But if you want to hide, for example, heating pipes, you will have to take a block with a cross-section of 50x50 mm or even larger. Of course, with such an installation, useful internal space is lost, but you have to put up with it, otherwise there is no other way.

And do not forget that electrical wiring in wooden structures must be well protected. All wires must be inserted into a metal hose. Now corrugated plastic tubes are sold for these purposes; they, of course, are considered self-extinguishing and cost less than metal hoses, but mice can easily chew through plastic.

Insulation of a wooden house from the inside is installed only in exceptional cases and is extremely rare. The thing is that with external insulation, the dew point is in the insulation, and if you install the insulation inside the house, it will be in the wooden walls, which will inevitably lead to their freezing.

The second most popular method of interior finishing of a log house is plasterboard. Drywall is especially relevant in services and in the kitchen. True, for wet areas you need to buy sheets with appropriate protection (moisture resistant).

In a wooden house, I prefer to install drywall not on a traditional metal frame, but on a wooden sheathing. Or screw the sheets directly to the walls, but this can only be done if all the wiring is already installed in the walls.

I have already told you how to fill the sheathing; for plasterboard, the spacing of the planks is selected in the region of 30 - 40 cm. The sheets themselves are screwed to the base with self-tapping screws, the heads of the screws should be slightly recessed into the sheet. But you can’t leave drywall clean; it needs to be puttied.

The technology here is not complicated. All joints between the sheets will need to be slightly widened with a knife; the groove should be approximately half the depth of the sheet, otherwise the putty will not adhere well. Next, prime the sheet, and when it dries, glue serpyanka (reinforcing fiberglass mesh) onto the expanded joints.

Now get divorced finishing putty and finish the sheet with it. You start by filling the joints and caulking the screws. When these areas are dry, take a wide metal spatula and apply a 1-2 mm layer of putty over the entire plane of the sheet.

If you plan to cover the plasterboard with tiles, then the entire wall will need to be reinforced with sickle before puttying. If you were unable to buy a self-adhesive serpyanka, then take PVA glue and glue the mesh onto it.

When finishing drywall for wallpaper, you can do without reinforcement, you just need to lightly sand the putty with emery. To paint, putty walls will have to be sanded to perfection. That is, start with coarse sandpaper and end with fine sandpaper.

Often, fragmentary finishing with natural or artificial stone is used inside a log house or in the basement area. This coating is quite heavy, plus there is a possibility of the base moving, so the base needs to be strengthened well.

After treatment with protective compounds and primer, a galvanized metal mesh is attached to the wooden wall. I usually use a chain-link and secure it with self-tapping screws, onto which I additionally put wide washers.

Most often, tile adhesive is used to install stone, but here it is better to consult a consultant, the fact is that special adhesives are produced for some minerals.

Previously, a reinforced wooden base was covered with a layer of cement-sand mortar, after which it was slightly leveled with a trowel and the stone was already laid on such a base.

Now, instead of cement-sand mortar, craftsmen use the above-mentioned tile adhesive; it costs more, but the reliability and quality are much higher. By the way, glue must be applied not only to the base, but also to the stone itself. Installation of such cladding is carried out from the bottom up, with a support strip attached at the bottom.

Conclusion

October 28, 2016

If you want to express gratitude, add a clarification or objection, or ask the author something - add a comment or say thank you!

We bring to your attention a catalog of houses made of timber. Various configurations and parameters of buildings will allow you to choose the project you like best and complete it turnkey in a short time.

Houses made of timber are different:

Reliability

The high strength and resistance of wood to external influences make timber construction one of the most popular options. To provide effective thermal insulation and structural rigidity; during construction, a profiled beam is used, which has two longitudinal protrusions on the upper mounting plane and two symmetrical grooves on the lower one, and the use of inter-crown insulation made of flax jute eliminates the formation of cracks.

Security

Ecologically clean materials, used in the construction of residential cottages, make a house made of timber safe for health. For an additional fee, wood can be treated by impregnation with special anti-flammable and antibacterial compounds.

Speed of construction

The average construction time for a house is 3 weeks (may vary depending on the complexity of the project). Thanks to modern technologies construction, in such a short time it is possible to install a full-fledged foundation and a two-story building with a finished roof.

No company can offer better and faster construction residential buildings. The price of a house made of timber is determined by the thickness of the walls; we offer 3 options for the thickness of planed timber: 100mm, 150mm and 200mm. both in the form of a standard rectangular profile and with a semicircular outer surface, while the cost of a house made from this material does not change. Careful design of timber construction projects allows you to quickly adapt to the features of the landscape.

Construction and finishing of a wooden house or bathhouse on a turnkey basis - rational decision for those who save money and time. The craftsmen of the MariSrub company have the necessary skills and knowledge that guarantee high-quality internal and external finishing of the building, reliable installation communication systems. We carry out a full range of tasks.

Design

Choose finished project Houses. The firm's architect will make the necessary changes taking into account the characteristics of the land plot and the client's wishes. For you spacious one- and two-story cottages, houses and baths with an attic, projects with a garage, terraces and balconies, country houses and guest houses, original gazebos. Didn't like any of the projects? Order custom design!

When you order turnkey construction, we carry out the project for free!

Production

The MariSrub company independently produces and processes lumber. Own production- guarantee low prices and quality of logs, because specialists monitor every stage of production. Wood is carefully selected and sorted. Logs are treated with special protective equipment, which will protect the material from negative external influence during storage and transportation.

The foundation determines the performance characteristics and service life of the building. Therefore, the choice of materials and installation of the structure must be approached very responsibly. “MariSrub” specialists will help you choose the appropriate type of foundation and perform the installation efficiently and reliably. We provide a full range of work:

Study of the land plot and design of the foundation;

Preparation of the base;

Laying of the structure and cladding.

Before pouring, specialists will determine the location of the wooden house or bathhouse, develop a project and carry out work to study the soil. The choice of design depends on the characteristics of the land and soil. We offer installation of strip, screw, pile-grillage and slab foundations.

Assembly and installation of a log house

Professional builders will quickly and efficiently install a log frame made of rounded and log houses on a plot of land. Big advantage log house consists in the speed of assembly and construction of the log house. Installation will take only 2-7 days depending on the complexity and area of the project. Installation of the log house will be carried out in compliance with the norms and requirements for construction wooden houses. A competent approach and extensive experience guarantee the reliability of the construction!

Roof installation and roofing work

Engineers design the roof and rafter system taking into account wind loads, rainfall and weather conditions, characteristic of this region. The experts will install a reliable truss structure and install a high-quality vapor barrier. In addition, they will help you choose the right one for construction. roof covering, components and additional materials. These are reliable and durable elements that harmoniously combine with each other and with the house.

We carry out installation of sheathing, arrangement of drainpipes, gutters and snow retainers, flashing of cornices and other types of finishing work, installation of dormer windows.

Installation of communications

Communications are carried out after shrinkage of the log house, which takes 6-12 months. MariSrub engineers will carry out step-by-step competent design and installation in strict accordance with established standards and rules of the following systems:

Electricity, closed and open wiring, laying the input cable in a trench and over the air, installing devices and elements (sockets, switches, etc.);
Natural and supply and exhaust (forced) ventilation, installation of ventilation devices;
Water and electric heating, pipe laying;
Water supply from a central water supply or an independent source, installation of wells and boreholes, installation of filters and pipes;
Sewage, installation of local treatment facilities, laying pipes and connecting plumbing.

Experts will carefully consider the rational arrangement of systems, which will save on installation and further operation of the wooden house. In addition, a well-thought-out arrangement of communications will make life easy and comfortable.

Interior and exterior finishing

The interior and exterior finishing of a wooden house is done very carefully. It requires attention, time and effort. Includes the following works:

Insulation and waterproofing of the house;
Installation of window and door openings;
Installation of windows, entrance and interior doors;
Installation of stairs, fences and railings;
Finishing floors, walls and ceilings in living rooms and bathrooms.

When working with walls, you need to pay attention Special attention. Log walls require caulking and sealing of seams, sanding and coating with protective agents (anti-peren, antiseptics and others). Only after such preparation can the walls be sheathed or left in in kind, only covered with decorative varnish or paint.

Finishing baths and saunas

When finishing a bath or sauna, it is important to properly treat the surface of the logs. After all, in such a room there is high humidity and frequent temperature changes. The experience and professionalism of the masters of the MariSrub company will allow you to achieve beautiful view and durability of the structure, pleasant atmosphere and comfort inside. They will select suitable materials that will not overheat or burn even at high temperatures and will withstand high humidity and will not rot.

In addition, we carry out the arrangement of baths and saunas. We provide hydro- and thermal insulation, install stoves and chimneys, and treat the premises with special protective agents. We carry out installation engineering systems, installation of windows and doors, covering walls, floors and ceilings.

The MariSrub company will perform a full range of construction and finishing works country houses and wooden baths. Own production, professionalism and experience of specialists, individual approach and affordable prices - a guarantee of a durable, reliable and aesthetically attractive home!

Wood is a material that is very popular for the construction of private houses. Although stone and brick are also popular, many people prefer timber, which creates a unique look for the home. But after the construction of the building, it is important to take care of the interior decoration of the house. For it to be successful, it is important to take into account all the features of a material such as timber and choose the most suitable type of finish. All possible options and nuances interior design houses will be discussed further.

Peculiarities

A house made of timber has a number of characteristics that are not typical for houses made of other materials. Among them there are both positive and negative qualities. The advantages of wood include:

The material is environmentally friendly.
A house built from timber has a very presentable appearance.
Constructing a building from wood elements takes less time than working with other materials.
There is no need to spend a lot of time laying an expensive foundation, since the timber will not create large loads.
Compared to other materials, wood has a lower price.

The nuances that cause difficulties are considered following points:

When the building is erected, all the internal work to be performed must be carefully planned. To the main procedures interior design and finishes include:

Laying communication systems. These include heating, sewerage, electricity, and water supply systems.

Coating walls with special compounds and antiseptics that protect against fire.

If desired, you can carry out thermal insulation and waterproofing of the floor and walls.

Next, the subfloor is laid.

To make the work more organized, it is recommended to prepare in advance a project for the arrangement and finishing of all rooms.

Partitions and other additional structures are being installed.

Walls, ceilings and floors must be carefully prepared before decorative finishing.
After this, the finishing itself is carried out.

The interior decoration of a building made of timber as a whole is a rather labor-intensive process, so it is important to describe in detail all stages of the work, as well as to choose the right material for finishing various surfaces.

Types of materials

There are many materials that are used for the interior decoration of a private house made of wooden blocks. Each raw material has its own special characteristics and is primarily used for a specific type of coating. The most popular materials for finishing a wooden house are:

lining made of plastic and wood;
drywall;
block house;
decorative plaster;
decorative rock;
vinyl siding;
dye;
tinting compounds;
varnish coatings;
laminate;
linoleum.

photos

Wooden lining fits on special sheathing made from wood. Using nails, slats and grooves, the beams are connected to each other and attached to the sheathing. The lining is made from various types of wood, which include pine, spruce, linden, and alder. The material significantly affects appearance, strength and class to which the products belong. IN The following classification is distinguished:

Extra class. Lining that has no defects.
Class A. Implies high quality, and even the presence of small knots does not spoil general form coverings.
Class B. Average quality, knots in products are more common.
The lowest class is C. It implies the presence in the material not only of knots and irregularities, but also of color variations.

Vinyl siding or plastic lining They are excellent for installation in rooms with various purposes, since these coatings are resistant to various influences. In addition, they create an additional layer of heat due to the voids present in the structure. Installation of plastic lining is carried out on a metal frame. The material with a vinyl surface is resistant to moisture and sun rays. Plus, it comes in a variety of color options.

The special material is decorative artificial stone, which is made from various raw materials. This material mainly plays an accent role in finishing profiled timber. The stone is placed on the crate, imitating various breeds. Using this coating, zones are identified in large rooms, and also accents are placed in the interior.

It is quite difficult to install such material yourself, so it is recommended to invite professionals for such work.

It is also worth paying attention to what kind of timber the structure of the house itself is made of. The beam can be made from different varieties wood The most popular is pine. It has the following characteristics:

Due to the soft structure of wood fibers, the material is excellent for processing.
This wood is strong and forms a completely reliable frame for the home.
Pine beams are environmentally friendly; they do not emit substances harmful to human health.
The shade of pine beams is usually uniform. Most often, natural material is painted in warm colors.
Despite all the positive characteristics, pine wood is sold at a price that is very affordable for the majority of the population.

Among other types of wood for constructing a log house, cedar, larch, spruce, and fir are popular. In many ways, their characteristics are similar to pine. Also, the beams can be laid according to various technologies, which determine the choice suitable material for interior decoration.

Drywall is a very flexible and plastic raw material for home decoration from ordinary bars. Before laying it, it is necessary to carefully treat the surface of the walls. The material is attached to a special frame structure. Most often, wooden sheathing is used as it; a layer of insulation is laid in the space between the drywall and the wall. The GLK sheets are fastened using screws, and the seams between them are subsequently treated with plaster compounds and become less noticeable.

For finishing coating Many formulations will work. Drywall is popular not only for finishing walls, but also for ceilings.

Alternative material for the frame is rounded laminated veneer lumber. Its difference from the standard one is that the construction in this case practically does not shrink. Walls made from such beams turn out smooth and elegant, so their texture is most often left visible during interior decoration.

Such a timber surface is treated with a special primer, and then paint and varnish mixtures are applied in several layers, which serve not only as a means of decoration, but also protect the surface from various influences. For the floor of such a home, laminate, ceramics or parquet boards. And the ceiling can be decorated using GLK or lining.

Some owners of private houses decorate their interiors using imitation timber relief. To create it use block house- a type of lining, which is a planed board, one side of which ideally imitates timber. The block house is installed on the sheathing, but it is not necessary to place it in all cases. It will be needed for laying a thermal insulation layer or masking communications. The sheathing is made from small bars or galvanized profiles.

The difference between a block house and an ordinary lining is that the latter can be laid both horizontally and vertically. The imitation timber is placed only in the horizontal direction.

Also, materials such as MDF or siding are used as imitation, but the block house has the greatest resemblance to natural bars.

Projects

To get a seamless and organic interior, it is recommended to design each room in advance and choose the most suitable style directions. In the design country house will become a relevant option chalet or hunting style. It looks very brutal and involves a combination of materials such as wood and stone in the design of the walls. Most often, rooms are decorated with clapboards, the walls are decorated with various hunting attributes, for example, animal heads or hunting equipment.

Russian style looks good in decoration interior decoration private house. It assumes the presence of a structure of beams on the walls. It is permissible to decorate the floors with laminate, imitating large boards. There must be a massive stove in the center of the room.

A house of this type can also be decorated in European, Scandinavian or provencal style . In these cases, a special feature will be the trim made of lining or siding in light shades. Sometimes a small number is welcome bright accents. Windows are decorated with light screens or curtains.

In style minimalism As a rule, large features dominate. This applies not only to the surface texture itself, which can look like beams, but also to other details, for example, windows and furniture. Having decided on the features of styles, you can choose the most suitable option to decorate your home.

How to sheathe?

No less important than the choice of material and style is the process of covering various surfaces of a wooden house with your own hands. The features of this procedure depend on the selected area. The main surfaces for decoration include walls, floors, and ceilings.

Ceiling

It is better to start the process of decorating surfaces from the ceiling, especially if you prefer to paint the ceiling and walls, or varnish them. The ceiling can also be sheathed with plasterboard and tension structures can be created.

If the ceiling is painted, its surface must be thoroughly cleaned and coated with a primer. After 24 hours, when it is dry, you can begin the painting process. To do this, use a long-haired roller. The process itself must be carried out quite quickly, since the paint quickly hardens on the ceiling surface. In this case, it is advisable to have an assistant who could point out color unevenness during painting (they can only be seen from below).

Instead of paint, the ceiling can be finished with clear varnish to highlight the structure of the wood fibers.

Walls

The walls of the room can be decorated various materials. But regardless of the selected raw material, it is important to remember that the first stage of work involves cleaning and degreasing the surface. The process of preparing walls also includes laying insulation and a waterproofing layer, and treating with putty. Some people prefer to simply plaster the inside of the house. But in this case it is worth remembering that it is not recommended to apply plaster soon after the construction of the house.

When covering beams with varnish or paint, the material should be applied in the direction of the wood grain.

For application coloring compositions a roller can be used, but for processing corners and hard-to-reach areas It is better to work with a brush. When choosing a varnish, pay attention to the content of harmful substances in it, as well as the texture itself, which can be glossy, semi-gloss or matte. Often, fabric wallpaper is even glued onto the leveled surfaces.

Floor

The arrangement of the floor is also very important point interior decoration of a house made of timber. In a private house there are two types of flooring – rough and finished.

The rough design represents the base. It consists of logs, between which a layer of waterproofing and insulation is placed. These layers are then covered with boards. For a private building It is recommended to make the floor with a double structure, since it is more capable of retaining heat. The finishing coat is applied directly to the boards.

Finishing is carried out in several stages.

Laying a layer of waterproofing on the subfloor boards. The material can be a polymer membrane made of film or roofing felt.
Installation of timber installed on an edge rectangular section 5 x 10 cm. The design features of this layer depend on the specific finishing coating.
Reliable fastening of the power set to the floor. To carry out this type of work, it is recommended to use self-tapping screws of the appropriate size.
Laying insulation in free space. Mineral fiber, rolled glass wool or even polystyrene foam can be used as a heat insulator.
Laying the finishing layer is the final stage.