Order in the garage means convenient open storage all frequently used tools and compact storage of various small items “in reserve”.
Often the garage and home workshop are combined, so all tools and consumables must have convenient system storage
As soon as the storage system becomes not very convenient for regular maintenance, the garage again turns into a spontaneous warehouse.
Best used for storing tools in the garage open shelves. It will be very convenient if these shelves are removable.
In the garage of the workshop it is necessary to place not only the usual set of car enthusiast tools and home handyman, but sometimes garden tools, and travel equipment.
Make the most of the entire height of the room. IN plastic boxes under the very ceiling and on the floor you can put those things that you use from time to time.
The tool storage system in the garage uses the entire wall area as a stand. Separate sections-shelves for storing tools and Supplies.
Wooden guides are used here, but it is better to use metal pipes. If over time the guide we see in the photo crumbles, a box with a heavy tool could fall right on your foot.
You can make such an organizer for storing consumables yourself from sheets of plywood, which are connected with hinges in the form of a book.
A lockable stand-box for home craftsman's tools will allow him to easily maintain the necessary order in the garage.
Metal mesh is convenient for storing paint cans, fertilizer bags, etc.
Metal guides and metal shelves not only guarantee safe storage of the tool, but are quite simple to clean.
It is inconvenient to keep a power tool in a company suitcase; it is much more convenient to make such an open stand for storage.
The owner has a lot of necessary little things in his garage, and each of them has its own storage method.
Most tool storage methods are simple, but still more effective.
Very convenient design for storing consumables! The box with screws that you use is secured to separate panel, and upon completion of work, push it into a general organizer.
Each owner has his own scope of activity and a different number of tools. But a convenient organization of work always makes you want to do something more. Take the time to tidy up your garage.
Sliding panels provide additional storage space for tools. Make sure that they will work reliably without getting stuck in the grooves, otherwise this storage method will not be practical.
Simple and convenient. Store your instrument wisely! If you don’t have a garage, and you store all your tools in a small box on the balcony, then even there you can organize a small work cabinet.
Let's continue for the happy owners of the garage. Before us convenient way storage of clamps.
Some storage ideas can be found in stores that sell tools.
But our garage contains more than just tools. We also have pipes, planks, and the necessary pieces of plywood and plastic.
It's not difficult to assemble one like this ceiling structure from pipes and in your own garage.
Large sheets of plywood and drywall are best stored this way - in a vertical position.
For scraps of plywood, plastic, etc. You can make a wall rack like this.
Even a dozen boards can create a mess in your garage. Let's do it simple design for storage.
Another convenient way to store long pipes and all kinds of strips in the garage.
A small workbench can also serve as a storage place for boards and pieces of plywood.
You don't have to clean out your garage in one day. All this can be done gradually, step by step.
A garage is not only a place for a car, but also a source of invaluable extra space, which can be used truly rationally if you design useful devices with your own hands.
DIY garage accessories
Since the garage, by its intended purpose, is a home for cars, you should be careful to ensure that the space for tools is well organized. Also in the room there will probably be several square meters in order to remove some of the items from the apartment so as not to clutter the living space.
During installation various devices indoors, it is important to consider that all available equipment is at hand. To do this, you can use the following recommendations:
Rational organization of space in the garage creates many tangible benefits:
- it becomes possible to independently carry out short-term repairs of car parts and other mechanisms, due to which you can significantly save money;
- Convenient placement of tools significantly speeds up work and saves time;
- Creation additional places for storing tools, old things, clothes, it makes it possible to unload the apartment from things that are rarely used in the household;
- finally, the well-thought-out internal logistics of the premises allow it to maintain its attractive appearance and avoid clutter.
NOTE. At the project development stage, it is important to proceed from the area of the room, and also take into account several mandatory utility compartments - for storing summer and winter tires, cans, jack, etc.
Video TOP best ideas for decorating a garage with your own hands
Garage rack: step-by-step manufacturing instructions
Since the garage always contains quite a lot of items, organizing their arrangement is a fundamental requirement for proper storage. The simplest and at the same time convenient option- this is the creation of a rack with shelves.
Preparatory stage
Before you begin installing the structure, you should consider several important requirements:
- The total weight of the rack should not be more than 4-5 centners - otherwise the structure will be very difficult to move if necessary. It will also put significant pressure on the floor, which can deteriorate the quality of the coating.
- When choosing materials, it is important to proceed from considerations of strength and durability of the structure. Metal is optimal, as well as wooden crafts from beech or oak. Plastic shelves are not suitable - they are not durable and, moreover, may not withstand temperature changes.
- Choosing between metal and wooden structure, you should proceed from your specific needs. Metal is more durable and stronger, but wood is more affordable. If you need to place a few tools, it is enough to make a small wooden rack.
- Since all the tools are very heavy, you should immediately calculate the strength of the structure so that it can withstand at least 100-150 kg on one shelf.
Installation of a wooden structure
To make such a device for a garage with your own hands, you will need ordinary working tools:
- hacksaw for wood and metal;
- hammer, nails;
- screwdriver, self-tapping screws;
- construction tape;
- construction level;
- electric drill.
All wooden parts Before assembly, it is important to prime and varnish. In the garage it can be observed high humidity or temperature changes - therefore, without treatment, the tree will not last long.
Video - Do-it-yourself wooden shelving technology
Installation of a metal structure
Metal structures are exceptionally durable and strong. In addition, they do not need to be treated with special materials to prevent rotting.
You can make both a rack and separate structures, for example, for storing rubber, from metal.
In this case, you should take into account the rules for storing tires, which are shown schematically in the figure.
At the design stage metal rack It should be taken into account that it can freely accommodate everyone necessary items. You can take this drawing as a basis.
Or this option.
The easiest option is to purchase a modular design and assemble it yourself. But you can make this device for the garage with your own hands. The sequence of actions is as follows:
It is better to place the heaviest equipment on the lower shelves for optimal load distribution throughout the rack. At the same time, the most the best option- When lower floors made of corrugated metal, and for the top it is quite acceptable to use durable chipboard.
Hanging shelves: fast and practical
Not in all cases there is a need to create a rack, since it will take up a lot of space. On the other hand, in a garage of any size there is always unused upper space, which can easily be used for hanging shelves.
Structurally, it is quite possible to make any version of such a device for the garage with your own hands:
The tools you will need are the standard set described above. The sequence of actions is as follows:
If the shelf is mounted to the ceiling, you can strengthen its connection to the wall using metal corners– then the product will not wobble and will last much longer.
The entire technology is shown schematically in the figure.
Making a shield shelf
The DIY technology for making such a device for a garage has its own differences compared to installing conventional shelves:
- The shield itself is made of durable plywood, the parameters of which are selected according to the situation. Visually, the shield should completely cover the surface of the desktop.
- Space is allocated on the board for all shelves and appropriate notes are made.
- Next, all the holes into which the dowels fit are made in the surface of the structure. It is on them that the hooks will be attached, on which all the tools will be placed.
- The shield is secured to the wall using brackets. The corresponding holes are made using a hammer drill.
All steps are shown schematically in the figure.
DIY tool panel above workbench in garage
Workbench for a garage: step-by-step instructions
Another structure that will probably be needed for repair, plumbing and other types of work is a workbench. It can be purchased in a store, but if you have a certain skill, then it is quite possible to make such a device with your own hands and put it in the garage.
Before carrying out the actual installation work It is important to clarify several important details:
- Where will the table be located?
- What kind of work will mainly be carried out on it.
- What work surface material is suitable - metal or wood?
All these questions are closely related to the purpose of the product. If work is expected to be done frequently, then it is better to choose durable metal. And for standard household tasks, durable wood will do.
It is important to understand that a workbench is not just working surface. Often it combines the function of a wardrobe, a small chest of drawers and even a metal safe - this set of parameters depends on the specific configuration of the product.
Types of workbenches
The key classification of workbenches is based on the types of work that are supposed to be carried out on it:
At the same time, these functions can be combined, so such a classification is largely arbitrary. The best option such garage fixture- this is a design on metal frame With wooden surface table and drawers. It is more reliable than its wooden counterpart, and allows you to save on manufacturing due to the fact that some parts will be made of wood. The table surface can be strengthened metal sheet– then the workbench will last a very long time.
Technology for making a workbench from a metal frame
To install the structure you will need a standard set of tools and materials:
- welding machine;
- grinder for metal;
- building level;
- jigsaw for wood;
- screwdriver, drill;
- self-tapping screws, anchor bolts;
- hammer and nails;
- metal corners with parameters 5*5 cm;
- square pipes 6*4 cm, total length about 24-25 m;
- steel strip 4 cm thick, up to 8-9 m long;
- paint for wood and metal processing.
These parameters are intended for the manufacture of a finished product with table parameters of 220*75 cm, as shown in the figure.
The sequence of actions is as follows:
Even at the stage of designing a workbench, it is important to decide whether the device will be collapsible or whether it will be permanently installed in the garage. In the case of a collapsible version, all parts are attached using self-tapping screws, and the principles of the technology will be different.
Wooden workbench manufacturing technology
A wooden workbench is less durable than a metal one. It is well suited for cases where the work is supposed to be done less often - several times a year.
To make this device for the garage with your own hands, you can use the same drawing given above, or take the diagram shown in the figure as a sample.
The algorithm will be something like this:
Do-it-yourself garage tipper: step-by-step video instructions
Along with creating the considered devices for the garage, you can also take care to make with your own hands the working tools that will be needed directly for Maintenance auto.
One of the most useful installations– a tipper for inspecting the bottom of the machine. The need for such a product is most relevant for Russian realities, since not in every case there is a real possibility of construction inspection hole.
Detailed video instructions with step by step diagram manufacturing
Before making such an installation, it is extremely important to consider the issue of safety. Even a light car can cause an accident if it falls and, at a minimum, will receive serious damage. Therefore, you can only undertake the creation of such a design if you have sufficient skill.
Making your own garage fixtures allows you to rationally organize inner space and essentially get your own workshop in which you can carry out any ongoing repair work.
Original ideas for organizing space in the garage
And finally - a photo selection visual ideas on creating spacious structures from a variety of items that are likely to be found in any garage.
A garage press is assembled from scrap materials. No complex parts are needed; it is made practically from scrap metal scraps. We will need:
- Two sections of channel, 80 cm long each, with shelf dimensions of 50x30 cm.
- Piece profile pipe diameter 40 or 60 mm, length 2.5 meters.
- Iron plate 8 mm thick, dimensions 250x250 cm.
- Two corners, one of which is 300 mm long, with a cross-section of 50x50 mm, the second is 250 mm long, with a cross-section of 25x25 mm.
- The hydraulic jack is the main mechanism of the press.
- Two springs and bolts various diameters for fastening. They are selected locally.
The base on which the press is located can be any plane, as long as it is strong and solid. Usually the press is installed on a workbench.
Homemade press on a workbench
First we make the side racks on which the entire mechanism rests. To do this, we take two sections of channel. From the bottom, for emphasis on each, corners are attached with the letter T. You can immediately make fastening points in them for subsequent installation on the base by drilling holes in four places on each edge. Then, using the same principle, a corner is attached to the upper part of the channel, and the pressing part of the press - a metal plate - is attached to it.
Now on the bottom of the support channels you need to make fastenings for the springs that return the press mechanism back. To do this, two holes are drilled and a bolt is screwed in from the inside. Then, using the same principle, the two upper fasteners are prepared on the underside of the pressure sheet.
Now all that remains is to make a stand for the improvised press. To do this, two profile pipes are cut, the length of which is slightly longer than the side supports from the channel. Connect them in such a way that they tightly grip the vertical posts of the press, but do not clamp them. A jack is installed under them, and holes are drilled in place for its fastening.
Improvised press on a stand
The homemade press is ready. For smooth movement, the side channel is lubricated with grease or oil. When the need arises to use it, the mechanism is installed on prepared mounts and the frame is tightened with bolts.
It’s easy to build an alarm system in the garage with your own hands; you don’t need any fancy “devices” for this. All that is needed is an old push-button telephone, a sealed contact, a spring switch, or better yet, a breaker and wires.
Do-it-yourself telephone alarm for the garage
The alarm is assembled as follows:
- On your phone, you need to set up a one-click call and enter your number.
- Then carefully disassemble it to connect the alarm wires.
- If the “hang up” and “call” functions on the device are controlled by one key, then the first wire is soldered to it, and the second to the number speed dial numbers.
- If these functions operate separately, then the third wire from the alarm breaker goes to the key.
- If the button is used with two contacts, then they are soldered onto the call and dial function button.
Assembling a homemade garage alarm from a telephone
When making such homemade products, keep in mind that the breaker button will play a major role. It must be installed on the edge garage doors between their opening and closing parts. At the same time, it should be positioned so that rain and snow do not fall on it. And the phone needs to be hidden in an inaccessible place, for example, in the far corner of the rack you built. To do this, you need to solder long wires to the contacts in advance. When closing the garage, the breaker button is pressed by the garage door leaf, and at this time the alarm is in standby mode. When the gate is broken into or opened, the contact opens and the circuit signal is sent to the telephone, which will dial the entered number.
Remember that DIY projects like garage alarms require a certain amount of secrecy. You don’t need to tell everyone what a craftsman you are.
It is simply impossible without such structures as racks with shelves. You can put all the little things, spare parts, tools on them and attach them homemade press in disassembled form. To ensure that such homemade products fit into the garage space, first determine the location for their installation. They are usually constructed on one side of a wall or at the end of a room. The width must be calculated so that there is free access to the car and the open doors do not touch the pillars.
To install shelving you will need:
- block with a cross section of 50x50 mm,
- sheets of chipboard or OSB for the construction of shelves,
- iron corners and nails.
The base of the rack must be strong, because the considerable weight of the laid out tools presses on the shelves. Carry out all the calculations in advance and only then start working.
The basis of a homemade tool rack
The block is attached to the ceiling first. To do this, you will need self-tapping screws with plastic plugs. Using a hammer drill, holes are drilled along a pre-marked line in increments of 20–30 cm. Plugs are installed in them and the block is attached to them with self-tapping screws. Then the plumb line determines the installation location of the lower bar. Both the top and bottom bars should be on the same horizontal line to keep the shelving level and strong.
Now you need to install the vertical posts. For better stability of a rack with shelves, they need to be fastened every 40–50 cm. They are fixed with nails, which are driven in using the “oblique hammering” method or using iron corners. We measure the distance from the top bar to the bottom and prepare according to the size vertical elements shelving frame.
Now you need to install horizontal jumpers to support the shelves, but first you need to mark the places for their attachment. For this you will need a tape measure. From the floor, mark the distance to install the first row of shelves on the rack on each vertically installed block. Then measure the distance between each stand. We cut the bars to these sizes. Now they need to be secured. We insert one between the posts and secure it with screws from the end, two on each side. This way we install all the frame elements. Then, from the installed bars, the second row of shelves on the rack is marked with a tape measure. They are installed in the same way.
Installation of frame elements of a homemade rack
Before installation, it would be better to calculate in advance the number of shelves on the racks and assemble the frame according to the drawn-up drawing or diagram.
Having assembled the outer frame, all that remains is to secure the bars to the wall to install the shelves. A line is marked on the wall, at the level of each row of cross beams on the frame. Then the horizontal position is checked with a building level and the timber is attached along the entire length of the structure according to the markings.
All that remains is to make the shelves for the rack and install them. We measure the distance from the wall to the edge of the frame and from one vertical post to another. According to the obtained dimensions, we cut the chipboard sheet, install it in place and, for reliability, fix it on top with self-tapping screws. We do all the shelves in the same way.
Shelves usually don’t have doors; you can hang a dark fabric curtain along the entire length. That's all, the place to store the necessary things is ready. All that remains is to model a homemade workbench and it will be completed in the garage.
It is impossible to make homemade items in the garage without having a workbench at your disposal. First, its support is assembled from corners or a profile pipe. It is better to connect these parts by welding. But if this is not possible, then bolted fastening is allowed. But for this you will have to additionally mark the joints and drill holes. Comfortable height finished workbench - 90 cm from the floor. This will make it more convenient to carry out work at the workbench. But for some it is better to repair while sitting, in which case the height of the workbench will be different. The dimensions and dimensions for each garage are different. And it’s better to decide on them before assembly.
Having assembled the base, we move on to making the tabletop for the workbench. Recommended thickness is 7–7.5 cm. Can be made from a single sheet of multilayer plywood 100 mm thick. If this is not possible, we will do it differently. Gluing a tabletop from several sheets regular plywood. Standard thickness– 1 cm and in this case 7 pieces will be enough. Having decided in advance on the size of the workbench (its upper part, where the table top will be attached), we saw off the plywood along it. You can use PVA glue for connection, but Moment or BF is better. It must be applied to each sheet separately and after waiting for 3-5 minutes, connect all the sheets.
Making a workbench top from plywood
After this, the glued sheets must be laid on a flat place and pressed down on top with a heavy load; everything should remain in this state for 24 hours. In order not to cut each sheet of plywood to size, you can first glue them together, and then cut out the table top for the workbench from the prepared material.
Now you need to cut off an iron sheet for the top covering of the working surface of the workbench, on which all work will be carried out (metal 4–6 mm thick is required). For accuracy, it is better to place it on plywood and trace the outline with an awl or nail. Then cut the sheet with a jigsaw equipped with a metal file. The tabletop must be secured with bolts, having previously drilled holes in it and on the workbench. After assembling the workbench, you can make small shelves and cabinets with doors in its lower part. Any plywood or pieces of chipboard left over after making the racks will be suitable for this.
Iron sheet for workbench top cover
A variety of homemade products make the life and work process of a car enthusiast much easier. There is no need to look in the corners to see where everything is, all the details are in their place. A simple-to-assemble alarm system will reliably protect the garage from burglary or car theft.
A garage is a second home for car enthusiasts. This building serves not only to shelter the car in bad weather, but also as a place to store all kinds of tools; it is often a “mini-workshop” for the owner, where almost any repair can be done. Each owner arranges his garage to suit himself. Some people do not take the equipment of the premises very seriously, and it begins to cause more problems than benefits. But still, most car enthusiasts try to adhere to certain requirements that are important to fulfill for more convenient maintenance of their car. So, arranging a garage with your own hands requires meeting certain requirements.
Primary requirements
Arranging a space for a garage means that it will be warm and dry enough.
Your car should not freeze even in very severe frosts. If possible, you can provide a system for quickly warming up the garage.
It is very important to reliably protect the premises from unauthorized entry. When setting up your garage, remember that access to tools or equipment that will be located in the garage should be as convenient and simple as possible. Therefore, it is better to think in advance about the location of storage areas.
In general, these are only the very minimum requirements that it is advisable to take into account for your own comfort. You can also add and equip the garage as you wish additional funds for repair and maintenance of your car. A workbench with tools and an inspection pit can be an excellent addition to the equipment of the room.
How to install racks and shelves
For the most comfortable arrangement of a garage, quite a lot of space is required, and this is often a problem. Storage of work tools and equipment also takes up quite a lot of space. Therefore, when independent arrangement In the garage, try to accommodate as much space as possible for shelves or cabinets, but so that they do not interfere with free movement around the room. Shelves can be hung anywhere where you won’t catch or hit them, above tables, windows, shelving, and so on.
The distance to the car when hanging shelves on each side should be at least 1 meter.
Quite often it is convenient to equip the wall that is furthest from the gate for a variety of shelves and equipment. This is where the main working tools, compressor, workbench, etc. are located. Everything is at hand and does not interfere with moving around the room.
Plenty of shelving in the garage is a big plus, but it's also worth considering a small closet to hang work clothes and put away some rags.
How to properly arrange a viewing hole
The question of the presence or absence of an inspection hole is quite individual. First, you need to decide how high the need for arranging such a pit is. There is no point in equipping it if you often use the overpass on the street.
If you decide that you need such a pit, then you must take into account that the walls and bottom must be concrete. The edges of the pit must be reinforced with iron corners. It is also worth considering what and how you will cover the inspection hole when not in use.
A drainage hole is needed in the corner of the pit; all the water that accidentally falls down will be collected in it. The hole must be made of such a size that it is convenient to scoop out the accumulated water. To avoid accidentally stepping into a hole while repairing a car, it must be covered with a grill.
In the pit you can place small equipment that may be useful for repairs; you can prudently make niches in the walls so that it is convenient to put the tools you are using. Also take care of lighting the inspection hole, install a lamp or arrange a place for a portable lamp.
Necessary equipment
For a routine wheel change or disc replacement, or carrying out the most ordinary work under the hood of a car, a standard set of tools and a jack are sufficient. But to accomplish more complex work– special equipment is required.
Crafting table
To make a workbench, it is best to use wood and metal. Work area It is best to cover it with a piece of metal, protecting the wood from rapid wear. It is better to make a workbench in two or three levels in order to arrange as many necessary things as possible.
For normal repairs the body will be enough for you welding machine either with tungsten electrodes, which are in a protective gas environment, or a carbon dioxide apparatus that welds metal with wire.
Such a device is used to purify the air from vapors, drops of oil, water and other small particles that may be present in it. This is very convenient device, used when painting cars, and promotes uniform distribution of paint over the metal.
Washing
Certainly, we're talking about not about professional car wash. And just about one that everyone can equip in their garage. To do this, you will simply need to connect a hose or pipe to supply water to the garage and drain it into the sewer. However, remember that electrical wiring and lighting will need more careful protection.
High-quality ventilation and lighting
It is very important to create in the garage high-quality ventilation, it will not only rid the room of unpleasant and harmful odors, but also protect it from the formation of dampness and excessive dust.
Ventilation holes are usually made on both sides of the gate on low altitude and covered with bars. The same holes are made on the opposite wall, but already under the ceiling.
Of course, the best lighting is natural, so if possible, you should consider having a window. If this is not possible, then make several lighting zones: above the work area, general and portable, which can be used to illuminate the most necessary things.
Video
You can see an example of the interior arrangement of a garage below:
Photo
Also, to arrange a garage you will need to buy metal cabinets for tools, racks, workbenches and other garage equipment that will fit into the interior of the garage.
As they say, there is never too much space in the garage. Men who spend a lot of time in the garage will agree that in some cases every minute and every square centimeter of free space counts. That is why a garage master needs competent organization of his workspace. Various people help out and help here in every possible way. devices for storing building materials and work equipment, machine parts and other things necessary for work. To ensure that your electronic, garden and garage gadgets are always in their place, use the following devices:
- stands;
- shelves;
- retractable panels;
- racks;
- organizers for tools.
Also, for clarity, we offer do-it-yourself homemade products for the garage and home craftsman - the YouTube video will reveal all the nuances of organizing the workspace and suggest fresh ideas.
DIY crafts at home with your own hands
Man has been making homemade crafts since prehistoric times. Actually, all industrial processes are the improved once handicraft or home-made developments of folk craftsmen. Sometimes we don’t even think about the fact that we pay for things that we can do with our own hands. DIY homemade schemes are easy to find online, and the materials can be purchased at a hardware store or found at home.
For example, from cardboard box and a piece of fabric You can make a convenient portable organizer for towels and other textiles.
The topic of storing all sorts of little things is inexhaustible, fortunately, as is the number of ideas. Good ideas for decor You can also draw from ordinary things - let them be buttons or empty tin cans. 
Cool shelves are made from ordinary drawers. How do you like this idea?
As you managed to understand, if there is detailed instructions It’s not that difficult to make homemade products with your own hands at home. The video will help you understand all the nuances of this have a nice lesson. Useful tips, interesting ideas- Everyone should watch it.
DIY crafts for the garden and garden with your own hands
At the dacha there is usually some free time for creativity and arrangement of the surrounding space. That's why It's worth having a few on hand fresh ideas
to implement them on your own summer cottage. Country homemade products at home, with your own hands, they can be ingeniously simple. From scrap materials you can make unexpected and extremely useful things for home use. 
Ordinary pebbles turn into fairy-tale animals.From an old teapot It makes a wonderful flower pot.
Used tires– it has already become a classic in the world garden figures.
Stylish lamps For country interior – do it yourself from regular can
and candles (don’t forget about safety precautions).
– great idea for a small cottage. 
Do-it-yourself homemade products for the garden and garden are often made by yourself, without unnecessary time and financial costs. Perhaps you had no idea how useful it is for household will turn out to be plastic bottles. Plastic bottles that have gone out of use can serve as the basis for an incredible decorative flower bed. 
Cool “blooming” pillars will significantly decorate your garden space.
Do-it-yourself garden furniture, successful homemade products: photos and drawings
IN previous sections We told you about homemade products that will become indispensable for the household and home life. However, we should not forget about rest, before which, nevertheless, you will have to work a little. Cozy armchairs, various tables and benches, swings and hammocks- all this country and garden bliss can settle on your site. We invite you to familiarize yourself with photo instructions and manufacturing drawings. garden furniture. We have selected the best options for you.
