Manual concrete mixer made from improvised means. How to make a concrete mixer with your own hands: video and drawings. From a milk flask

Many people like it on their personal plot carry out repairs yourself. To fix the foundation of a house, fill paths, or install fences on posts, you need a machine such as a concrete mixer. There is no point in purchasing an industrial model, because it will be very expensive. In this case great solution You will be able to make a concrete mixer yourself, which will not require large financial costs. So how to make a concrete mixer yourself? Thanks to the presented video, you can clearly see the entire process of such manufacturing.

Why is a concrete mixer needed?

Many people believe that a small amount of The solution can be easily mixed with a shovel. However, this results in a very low quality mixture. The fact is that it is very difficult to stir the solution in a trough with a shovel. Such exercise stress not everyone can do it, so easier to install the concrete mixer, assembled with your own hands from a barrel. In addition, if you mix a large amount of the mixture, the composition will end up dry. The solution begins to lose moisture much faster than it can be stirred to the required consistency.

You won’t get good quality concrete even if you use a drill. When you attach it to the bracket, lumps of sand remain in the mixture. The drill must not only spin, but also move back and forth and in a circle. Often the tool cannot withstand such stress and breaks.

To understand the principle of operation of a homemade concrete mixer with your own hands, which is made for a small amount of work, it is necessary to consider the process of mixing the solution. There are 3 ways:

gravity method;
vibration method;
mechanical method.

Gravity method. This method is not used in industry because the resulting cement is of low quality. As a result of gravitational mixing, the container tumbles over, the components begin to “plop” on top of each other and mix into a relatively homogeneous mass.

Vibration method. Counts the most reliable production method concrete in industry. In the fixed tub, a vibrating mixer begins to move, resulting in a high-quality solution.

Mechanical method. Can only be used in conjunction with gravity. In this case, either the mixer begins to rotate in a stationary tub, or the tub with protrusions inside rotates.

Concrete mixer manufacturing technology

There is a large number homemade units, which are adapted for the production of concrete. Most simple design can be made from an ordinary milk can, a large saucepan, or old boiled milk. Its drawing is quite simple, and its manufacturing technology is even simpler:

weld the container to the axis;
insert a stick, a piece of pipe or a rubber band into the lid and pull the lid very tightly towards the handles;
to simplify the design couplings are not used, and cut arc-shaped recesses in the frame and lay the axle on them.

To make a more practical unit, it is necessary to use other drawings.

Stages of making a concrete mixer with your own hands

Making a container

Before you start creating a concrete mixer with your own hands, you should choose a container. Best to use for this metal barrels, which can hold at least 200 liters. Exactly this volume is considered optimal in order to knead required amount concrete at a time. It is better not to use plastic tanks, as they will not last long.

To make a concrete mixer you will need a barrel with a lid and a bottom. If the container initially does not have a lid, then it should be welded by cutting it out of a sheet of metal. After this, flanges with bearings should be attached to the bottom and lid of the barrel. A hatch is cut into the side, through which the components of the solution will subsequently be poured. It is best to make such a hole closer to the end of the container, which will be lower during the operation of the concrete mixer. The cut out part of the barrel will be used as a hatch cover. It is secured using hinges and some kind of locking device.

In order for the solution to mix better, blades are welded to the inner walls of the barrel at an angle of 30 - 40 degrees. The angle of inclination is calculated in such a way that during the mixing process the concrete can be “pushed” outward. In addition, such the blades can be fixed not on the walls, but on the shaft of the device itself.

If you cannot find a suitable container, you can make it yourself. To do this you will need the following tools and materials:

sheet metal 1.5 - 2 mm thick;
welding machine;
rollers;
wooden mallet or hammer.

Before you start cutting metal, drawings should be prepared indicating required sizes. To make the concrete mixer body, you will need a central round section, the bottom of the container and two truncated cones that make up the lower and upper parts of the structure. The parts cut according to the markings must be bent into rings. It is more convenient to do this using rollers. After all parts have been adjusted, the seams are securely welded.

Base installation

A homemade concrete mixer must have a reliable and stable base. Otherwise, the structure may tip over during operation. If it is not intended to load a large amount of concrete into it, then it is better to make the frame out of a square one wooden beam , having a cross-section of 10x10 or 15x15 cm. To ensure that the base of the structure does not suffer from vibration during operation, you should use “half-tree” or “tenon” type connections. After assembly, all joints must be properly glued and tightened with self-tapping screws.

If you want to create a more reliable and durable unit, you should give preference to a frame that welded from metal corner size no less than 45x45 mm. You can also use a channel. If there is no gas welding machine, then the frame is secured with rivets or nuts and bolts.

If there is such a desire, the base can be equipped with wheels. This will require an axle without bearings and the wheels themselves. This concrete mixer is easy to turn over and move. When assembling the base, it is necessary to provide handles. With their help, the device can be moved.

During the assembly process, the frame must provide space for the engine. Also a counterweight will be needed so that the structure does not topple when unloading concrete. If you plan to unload the solution with a shovel, then in this case a counterweight will not be needed. All these points must be provided for during the creation of the drawing.

Engine installation

To make the concrete mixer more efficient, you need any single-phase motor whose rotation speed is no more than 40 rpm.

Many masters who create homemade design, it is recommended to use electric motors from old washing machines out of order, such as “Volna” or “Chaika”. Such motors are able to operate for a long time and not overheat. When choosing an engine, you should remember that optimal speed The rotation of the tub is 20 – 30 rpm. For this, various gearboxes are used. However, optimal and simple option is the use of a pulley and a drive belt.

Instead of a washing machine motor, You can use a motor from a motorcycle or a gasoline-powered moped. In this case, the concrete mixer will not require power supply and can be used in any conditions. The engine is mounted using 4 bolts to the bracket or frame, which are welded to the gearbox housing.

However, a homemade concrete mixer can also work using manual control. In this case, neither electricity nor gasoline will be needed. Such a simple device is mobile, easy to assemble, and anyone can operate it. Its only drawback is the presence of an assistant to mix the solution.

Finally, a shaft is threaded through the container of the structure. To make the device more stable, it should be dug into the ground at an angle of 30 degrees.

Thus, to make a concrete mixer with your own hands, no special skills are needed. The manufacturing process can be seen more clearly in the video. Before you start assembling such a device, you should use the drawings. They will help you correctly and accurately create a homemade design without major financial investments.

When starting a construction project, anyone at least once has a question: how to make a manual concrete mixer with your own hands? It's quite a tedious task, mixing in a bucket.

Tub for combination mixer- is not the best option. In the corners, the solution does not mix properly, and for a better solution you need to rotate for a very long time, consuming electricity. For small portions of the solution, a good tub is obtained from two identical basins. If the stirrer will be used occasionally, you can also use plastic basins secured along the rim with metal tape. The bottom of one of the basins needs to be cut out. This tub will only be tiltable: side unloading is not possible. The neck of this top-discharge bucket must be reinforced with two transverse bars.
The drive is used in factory-made mixers, it is expensive and you cannot make it yourself: you need special equipment. For a high-quality replacement, the following elements will be needed: a flywheel (even an old one from any car engine will do); gear (take it in the same place as the previous option); wheel hub - from the same car.

Incorrect selection of tub. You need to choose a round one, high and not very wide: the distance from the edges of the vibrator to its walls should be equal to its radius.
Flat vibrator. If you make it from metal sheet, then this will not excite a certain system of internal waves in the solution. An excellent vibrator can be made from two folded metal plates or saucers.
Big vibrator. Typically the vibrator diameter is 20 cm/kW. A wider one will not be able to mix well.
Incorrect position of the vibrator. In general, the vibrator should be located along the axis of the tub at a distance equal to its diameter from the bottom. The solution above the vibrator should also be equal to its diameter. If these conditions are met, the quality of the solution will be excellent.
Controlling the duration of mixing the concrete mixture. If the mixture stops gurgling and moving, this means the solution is ready. IN in this case– 10 minutes minimum will be enough.

Concrete mixer drawings

A do-it-yourself concrete mixer is necessary for construction work. If you need to erect a building, you will need a lot of concrete. Even a wooden building requires a solid concrete foundation. In view of this, it is impossible to save on material.

DIY options

Don't know how to make a concrete mixer? There are several options. A simple option is a handmade product that works using human power. Difficult option - homemade device using an electric motor. It should be made from improvised means.

Making at home requires observing the nuances. The product must be:

Safe. It is especially important to pay attention to the gearbox powered by electric current.
Low cost, ease of production. The parts you need for production should be cheap.
Ease of use. A mechanical concrete mixer is practically no different from a manual machine, and it is much easier to use. Decide in advance on the type of device.

Materials and tools

For a concrete mixer from a barrel manual type you will need the following materials:

channel;
card loops;
Bulgarian;
200 liter barrel;
bearing housings;
metal corners (50x50 millimeters);
welding machine;
fasteners;
flanges;
pipe.

How to make a concrete mixer with your own hands with an electric motor? Additional materials required:

electric motor;
pipe sections;
rod reinforcement;
corners.

DIY concrete mixer from a barrel (video)

Step-by-step instruction

Cut holes on the side (24x30 cm) - they are required for laying the concrete components and the hatch.
The hatch will be opened using card hinges.
Flanges are fixed to it. Inside the barrel they will prevent the walls from breaking.
The comb is made from corners. It speeds up the process of preparing the mixture. The length of the corners is 760 millimeters; they are installed inside the barrel. The pins are fixed to the corners by welding.
The elements are welded. The racks are placed near the ends of the barrel.
To give the concrete mixer stability, the supports of the racks are dug into the ground (the depth should be 30 centimeters), and the soil is compacted.
Levers are attached to both sides of the shaft. The length of the handles should ensure that the drum can be rotated with both hands.

After the concrete mixer structure is ready, it is placed on the site. It is necessary to choose a place where the concrete components will be stored. They are inserted through the hatch, then the shaft is rotated. To ensure mixing of the mixture, 15 revolutions are enough.

Important! Build-ups may appear inside the barrel. For cleaning, stones and water (1 bucket) are placed in the drum. Next, it is enough to make 25 revolutions of the shaft. The contents of the barrel are then emptied.

Engine Installation

The production of a barrel with an electric motor is carried out using a single-phase motor. Its rotation speed should be less than 40 rpm.

You can use motors from old washing machines - “Volna”, “Chaika”. They have sufficient torque. It is important to remember that the optimal rotation speed for the tub is between 20 and 30 rpm. For this, different gearboxes are used. The easiest way is to use a drive belt and pulley.

It is also allowed to use a motor from a motorcycle running on gasoline. This device is convenient to use because it does not depend on electricity. A chain reducer will help reduce the rotation speed. The engine is attached with 4 bolts to a bracket welded to the body.

Free concrete mixer plans

Important nuances

To make it convenient to use the device, it is worthwhile to provide a structure for overturning (it is made from corners) and a mechanism for transportation.
Before manufacturing, it is worth taking into account individual characteristics and showing design resourcefulness. This is the only way to create a product that will be convenient to use.
For quality work The rotation of the shaft must be ensured through the bearings. The maximum dose of solution is limited to 7 buckets.

Drawings: design features

It is not difficult to draw up a drawing for creating a concrete mixer. To make a simple device you will need a bucket, a drill, and a bracket. But you can also produce little concrete. However, using the presented design it will be possible to make concrete for garden path or filling the floor in the room. To carry out large volumes, an appropriate capacity is required - from 150 liters. It can be welded from sheets of metal.

The next stage is the construction of the base. It should also be reflected in the drawing. The foundation must support the weight of the machine and concrete. It must also be stable. When performing minor work, a frame made of timber with a cross-section of more than 100 millimeters is suitable. For large volumes, a metal frame should be preferred. The structure is assembled using welding.
The engine can be made from an old motor washing machine. To ensure the required rotation speed, it is worth using gearboxes. They can be made of belts and pulleys.

Even during production simple device, drawings are required. They are much easier to work with.

Operating principle of a concrete mixer (video)

To carry out construction work, you simply need a concrete mixer. You can do it yourself. The product can be manual or equipped with an electric motor. Don’t forget about the drawings; with their help, the work will be completed quickly and without errors!

To avoid losing the material, be sure to save it in your social network VKontakte, Odnoklassniki, Facebook, just click on the button below.

A self-assembled concrete mixer helps save time and makes heavy work the job is easy. From the article you will learn what and how to make this unit yourself.

Concrete mixer: what is it for and how to assemble?

Why do you need a homemade concrete mixer? The title itself already has the answer. This is a unit that is designed to mix sand and cement with water to produce concrete. Why concrete is needed, every schoolchild knows about this today. You cannot do without this material if you are going to build a house, or, say, improve the territory - so that there is a clean yard and smooth paths.

Of course, you can arm yourself with a trough and shovel and make concrete by hand. But why do you need Sisyphean labor when you can use a special machine for this? There is no point in buying a concrete mixer if you do not intend to take on construction contracts. It is much more interesting and economical to assemble it yourself. Moreover, an old two-hundred-liter barrel will do for this purpose.

The site’s site masters have prepared a special calculator for you. You can easily calculate required quantity concrete.

The device you end up with is reliable and easy to use. All you have to do is pour the ingredients into the drum in certain proportions and add water. The ratio of components depends on what you need the solution for. Usually, to get high-quality concrete, take one part of cement and add to it one part of sand and screenings (small pebbles). It is possible, and in some cases even necessary, to replace the components with a sand-gravel mixture (SGM).

Homemade concrete mixer from a barrel - advantages and disadvantages

An undoubted advantage in making a concrete mixer with your own hands will be a significant saving of money on purchasing a factory model. Besides, have you seen the equipment that most sellers offer? Even if you have an extra thousand and twenty rubles, you are unlikely to want to give them for a Chinese product of dubious quality. And then, if the Chinese can do it, then why are you worse? It is not the gods who burn the pots. Your unit will serve faithfully not only to you, but also to your grandchildren.

The disadvantage here will be, especially if you are not a technician by training, the lack of experience in the manufacture of such mechanisms. But if you are persistent and love to tinker, you will certainly succeed. Good, necessary details literally lying under your feet. Of course, they won’t come to you on their own. You will have to rummage through a pile of scrap metal in a garage or even a junkyard.

But don't be so scared. To make a concrete mixer at home you will need: a container (in your case old barrel), in which the process of mixing the solution will take place, an axis of rotation, an electric motor (if you are not going to rotate the drum by hand) and a frame for the base on which all this will be attached. As you can see, all ingenious is simple. You will learn how to prepare and what tools you will need to realize your idea in the next section of this article.

Preparation and tools

Before you start working on a concrete mixer, you need to make a drawing or at least a sketch of the future project and prepare working space. A garage or shed is best suited for this. The main thing is that electricity is supplied to it, because in this case you will need power tools. And the work with metal itself is quite noisy and dirty. Agree that a comfortable apartment is not the place where you can engage in such creativity.

Well, the drawing is ready, and you have prepared the place: you have removed everything that is not relevant. Now let's see what tools you need. If you don’t know this craft and will assemble the entire structure with bolts, you won’t need a welding machine. But you definitely can’t do without a drill. You will also need a set of screwdrivers and a hacksaw. And, of course, the main part of the future concrete mixer is a two-hundred-liter barrel.

It would be great if the bottom of the container was non-removable. Otherwise, it may simply fall off during the process of mixing the solution. The frame can be made from a metal corner. It is more convenient than pipes when connecting with bolts. You can install a gasoline engine or a motor from a drill-mixer as a motor that sets the torque. The main thing is that its power is at least 1.3 kW. And don’t forget to think about and install paddles inside the barrel for the most effective mixing of the components.

Important: the top lid of the barrel must be securely fastened, otherwise you risk covering the entire area with concrete.

In addition, even at the development and preparation stage, think about what kind of future concrete mixer you want to see - mobile on wheels or stationary. Then you won’t have to hastily adjust the drawings and make changes to the almost finished design. If you have everything ready, then you can start the most interesting part - making a concrete mixer with your own hands.

How to make a concrete mixer - let's start making it

Let's look at the key stages of the work.

We assemble the frame of the future unit. It must be durable, because it will have to withstand enormous loads. For the base, a 130 mm steel angle is best suited. Since we decided to do without a welding machine, it wouldn’t hurt to tell us which bolts to choose for assembling the frame. The best option There will be bolts with a diameter of 27 mm. The angle of inclination of the barrel to the base should be 35 degrees. If you have not found a suitable motor, you can make the drive manual. Of course, you will have to make some effort, but it will still be better than mixing concrete with a shovel in a trough.
Before placing the barrel on the gearbox (a device that converts the high angular speed of rotation of the input shaft into a lower one on the output shaft), you need to attach, say, a ring gear (a hardened steel disk with teeth) from a Volga engine to its bottom. Practice has shown that it is optimally suited for this purpose: it is made of hardened metal and has teeth on the outside.
If there is welding, then attaching the crown is as easy as shelling pears. But we decided to assemble the concrete mixer without using a welding machine. Therefore, we will attach the crown to the bottom of the barrel with bolts. Turn the barrel upside down and attach the crown to the bottom. Make marks on the bottom of the barrel with a core (a special rod with a sharpened end). Simply insert the core into the hole in the crown with the sharp end and hit the blunt end with a hammer. Then remove the crown and drill holes using a drill strictly according to the marks made with the core. Place the crown back on the bottom of the barrel so that the holes line up. Insert the bolts and tighten the nuts on them using wrenches.
We put the gearbox on the frame. We do the same as with the crown. We mark the place for the holes on the frame with a core, drill, bolt the gearbox to the frame, and install the barrel itself on it, first not forgetting to make blades in it in order to. Making them is also easy. You can simply fasten three corners along the length of the barrel with bolts at an equal distance from each other. We replace the small gear pulley with a suitable gear. This is what will set the heavy container of concrete in motion. In order not to suffer for a long time and not to reinvent the wheel, the small gear can be taken from the Bendix starter (Bendix is the starter armature shaft) of the same Volga.

The most an important part the whole machine is the engine. It must be securely attached to the bracket on the frame.

To tip a barrel of concrete, a steering wheel is suitable, not just a handle. Making it is not that difficult. Essentially, you can take a sleeve (a piece of pipe) and screw the rods into it radially. Then put it on the additional gearbox and secure it. But if such a design causes difficulties in developing drawings, then you can simply use a shovel ready solution from the container. Just remember to turn it off first and wait until it stops.

Even though you will assemble the apparatus yourself to help mix concrete, this does not mean that you can neglect basic safety rules. Yes, they have already set everyone’s teeth on edge, and yet, traumatology statistics show that not everyone follows them. Remember them well, or better yet, write them in bright paint on your concrete mixer:

Do not, under any circumstances, climb inside a spinning barrel.
If you have assembled a unit with an electric drive, make sure that the power cord is in good condition.
Keep small children away from even a non-working machine.
If you have made a mobile structure, put a support under the wheels before you start using it.
When mixing concrete, strong vibrations occur. Therefore, monitor the condition of the screw connections and tighten them in time.
If possible, wear work gloves or gloves. Cement can cause an allergic reaction to the skin of your hands.
And never leave switched on equipment unattended.

Remember that you are responsible for your health and the safety of those around you! So, making a concrete mixer with your own hands is not at all difficult. The main thing in this matter is the presence of everyone necessary tools, materials and, of course, desire. But you will have an inexpensive and great tool, which may be useful to you more than once. By the way, you can rent out your concrete mixer to your neighbors and get a good increase in your salary from this.

For this purpose, various cement mixtures, as the most affordable to date construction material. If the amount of work is small, then you can prepare the cement mortar with a construction mixer or in a small bucket, mixing it with a shovel.

But if you need a path in front of the house and pedestrian paths, build a stone shed or make a fence with concrete base and brick pillars, then it is advisable to have a mechanism on hand that will ensure the preparation of a cement or concrete mixture. In we will tell you how to make a concrete mixer with your own hands and what materials you will need for this.

Existing types of concrete mixers

Main types of cooking devices cement mortar or concrete are determined by the mixing method.

He can be:

gravitational, based on the simple turning over of the constituent components of the mixture;
mechanical, which resembles gravity, but to improve mixing, additional dissecting elements are added to the design;
vibration, in which the mixture is prepared thanks to a vibrator immersed in it;
combined, where two or three mixing methods are used simultaneously.

Each type of concrete mixer has its own positive and negative qualities, which depend on the cost of materials, the complexity of production and the required level of quality of the concrete solution prepared in them.

Gravity-type mechanisms

This is the simplest manual concrete mixer with your own hands, requiring a minimum of cost and effort in production. However, the quality of the prepared mixture in such a device can be called no more than satisfactory, and it will not be possible to produce large volumes of solution in it.

And yet, with relatively small requirements for the solution, given its simplicity and low cost, such a do-it-yourself concrete mixer is quite widely used when performing construction work on personal plots.

Structurally, its design is a horizontally located, closed container with an opening door through which components are supplied.

For more convenient use of a gravity-type concrete mixer, it is installed on a welded support frame.

You can use a metal can or an ordinary steel barrel as a container. After bookmarking necessary materials through the door, close it tightly, and begin to rotate the container using the handle. After mixing, the gravity-type concrete mixer is turned with the door down, and the finished solution is dumped through it into a tray.

Mechanical mixers

Homemade concrete mixer with your own hands mechanical type outwardly very similar to gravitational. The main difference is inside her.

These are guide and cutting blades welded to the inner walls of the container. They direct the fall of the overturned layers, cutting them into separate parts.

In this case, the dough will be of higher quality and in a shorter time. The presence of blades changes the very principle of gravitational mixing. Therefore, the working container can be positioned not only horizontally, but also at an angle, which allows for more efficient use of the volume of the concrete mixer and makes work more convenient.

Schematic illustration of a mechanical concrete mixer.

In addition, a working container installed at an angle to the horizontal no longer requires a sealed lid, and the finished mixture can be dumped through a constantly open hole by turning the working container itself over.

Making a working container

You can also use a steel barrel as a working container, to the inner walls of which steel blades should be welded at an angle of 30-35 degrees. The height of the blades should be equal to a quarter of the diameter of the barrel. It is possible to weld the blades to a rotating shaft running inside.

More difficult option There will be a container of our own design, a kind of homemade product. To do this you will need a piece of steel thin wall pipe with a wall thickness of 2.5-3.5 mm, a diameter of at least 800 mm and a length of at least a meter.

The supporting frame is best made from steel profile pipes.

One side of the pipe is welded with a steel circle. On the other side, 4-6 triangular segments are cut out, which are folded to the middle and welded together. The result is a container resembling a pear. The blades are welded inside the pear, and in the center, with outside bottom, - a steel axle for subsequent fastening of the drive pulley.

They are less susceptible to bending than angle bars and are relatively lightweight. The frame design should include the installation of support wheels on which the container will rest, and a platform for installing the electric motor.

The frame itself should consist of two parts:

the support on which the entire structure will be supported;
rotating, on which the working container will rest.

Support frame with handle and wheels.

The supporting and rotating parts of the frame are connected to each other through short shafts mounted in bearings or bushings.

A transverse handle must be welded to one of the shafts to allow tilting of the rotating part of the frame, and with it the working container, which will lie on the frame, resting on wheels.

Mechanical concrete mixer drive

The drive for rotating the mixer in devices of this type is extremely rare and only with a small volume of working capacity. Typically, an electric motor connected to the mixer through a belt drive is used for rotation.

It is even better to connect the electric drive through a gearbox, but a self-made concrete mixer in this case will be too expensive in terms of the necessary components. In factory designs, you can see a gear drive from a motor mounted on the side of the tank, at the point of greatest diameter, but at self-production such a solution is feasible only theoretically.

Vibrating type concrete mixer

Vibrating devices are widely used in the industrial preparation of solutions and concrete mixtures because they provide best quality final material. They are very simple in design, and then making them yourself is quite easy.

During operation, the components begin to actively mix, and water is gradually added until the required degree of solution thickness is obtained. At the end of the process, a hatch opens at the bottom of the tank, and ready mix falls into a pan or car body.

Structurally, such a concrete mixer is a stationary container located vertically. In the upper part, the necessary components for preparing mortar or concrete are loaded, a certain amount of water is added, and a submersible vibrator is lowered into the middle.

If you already have your own submersible vibrator or you have the opportunity to purchase one, then making such a concrete mixer yourself will not be difficult. There are no moving or rotating parts, there is no need to invent a drive and a rotating frame design, but simply install the improved barrel design on the support frame and place the receiving tray below.

The main difficulty in operating such a design is the need to ensure a stable position of the vibrator. In order for the finished mixture to be obtained High Quality, it is necessary to place the vibrator strictly in the center of the volume occupied by the prepared solution and mix it all at the same time.

On industrial enterprises For this purpose, a special lowering structure is used, on which the working mechanism is fixed.

If you decide to use a steel barrel as a working container, then first of all you need to remove the bottom and lid. After this you need to make from steel sheet a truncated cone, the larger diameter of which should be equal to the diameter of the barrel, and weld an opening gate to the smaller diameter. You can buy it or make it from existing corners and a steel plate with a handle - then you will get it for free. Weld the manufactured cone to the barrel, and the working container will be ready.

Now you need to install the container on a support frame, the height of which will ensure that a receiving tray can be located under the concrete mixer. It is best to install it with a slight slope or feed the solution into it through a receiving chute, and install the tray itself next to it.

Finally

When deciding to make a concrete mixer with your own hands, you need to understand that its manufacture will require a large amount of welding and plumbing work. You must have such skills or have an assistant who can do this. It would also be a good idea to look online additional photos and video materials, having become familiar with the experience already accumulated by other people.

The work should begin with identifying the materials already available. Based on such an audit, it is necessary to make drawings or a sketch diagram of the future device. After this, purchase all the missing materials and tools, and then begin manufacturing.