The garland, which is most often used to decorate the New Year tree, can be used as a component for the manufacture of a lighting device. A DIY garland lamp is easy to make.

To make a lamp you will need a garland, a plastic lampshade and a stand.

At the same time, the lighting in the room will be soft. This lamp can be used as a night light. The designs of such homemade lamps can be varied depending on imagination and source materials.

Lamp made of disks and garlands: production

The following materials will be required:

CDs or DVDs that have no graphics on both sides;
garland for 15-20 light bulbs;
glue and a gun for applying it.

The assembly of such a lighting device should begin by making a geometric figure, for example, a cube or a three-dimensional pentagon, which will serve as the basis. To do this, apply glue to the disk and immediately apply another one. The discs are sequentially glued together until the desired shape is obtained. But, in order to make it more convenient to place inside the cube, one of its sides should not be sealed.

To attach the disks you will need a glue gun or wire.

After all the disks are glued together, a garland is placed inside. It is positioned in such a way that the plug and control box are in the window formed by the joint. Several light bulbs come out into the holes. The number of windows placed inside can be from 3 to 5, depending on the size of the light bulb. The luminous elements must completely fill the hole, thereby creating the desired effect. The remaining part of the garland that does not fit into the holes is placed evenly inside the cube. You should leave a few more bulbs in order to thread them through the last line, which is formed after gluing the last disk.

For ease of installation inside the holes, they can be secured together with tape or insulating tape. In addition, the resulting group can be additionally secured with glue or sealant during their placement in the lamp disks.

After all the holes are filled with light bulbs, you should glue the last part of the lamp cube. The light bulbs left for this purpose are threaded into the last disk.

You can use another disk as a stand. The resulting cube is glued onto it using glue, placing it on an edge. This placement will allow the lighting fixture to stand stably in the future. In this case, it should be taken into account that the socket and control box are placed at the bottom, but are not glued.

After the structure is installed on the stand and the glue has completely hardened, the lamp is ready for use.

Return to contents

Lamp made of plastic packaging and garlands

In order to make this model, the following materials and tools are needed:

The basis. It can be used as a plastic bottle of any size or a plastic packaging box of various shapes, for example, a pyramid-shaped candy box.
A garland, the number of bulbs in which depends on the size and shape of the chosen base.
White paint. It is advisable that the paint be in a can. This will allow it to be evenly distributed over the entire surface in an even layer.
Soldering iron with a sharp tip (or electric drill and drill bit diameter).
Construction knife.

Before making the slots, markings must be made. They can be placed symmetrically and 1 piece per hole (or in the form of any pattern with several pieces inside). On the base at the bottom it is necessary to make a cut through which a wire with a socket and a control box will subsequently be passed.

If the material from which the base is made allows you to make holes using a soldering iron without damaging it, then it is better to use it. If the integrity of the structure is damaged when exposed to a heated soldering iron, it is necessary to use a drill and a drill for work. According to the markings, holes are made using the tool that is suitable for the selected base.

If, as a result of making holes, sharp edges are formed or part of the plastic remains outside or inside, then these remains must be carefully cut off using a construction knife. This must be done carefully and in such a way as not to damage the rest of the base.

After the processing of the grooves is completed, you can begin painting. The base needs to be painted several times so that a uniform white color is formed over the entire surface.

After the paint has dried, you can place the light bulbs in the holes.

For ease of work, you should start from the top. After all the light bulbs are placed and the wire with the socket and control box are placed in the slot, the base should be covered with a lid. This will allow you to move the lamp around the room. The lamp is ready for use.

How to make a New Year's lamp from a garland? 20 photo ideas. DIY garland night light

DIY garland lamp: making

garland for 15-20 light bulbs;

Return to contents

Construction knife.

moyagostinaya.ru

DIY garland night light video Video

1 years ago

Unusual Lamp from a Jar and Garland!!! Subscribe https://www.youtube.com/channel/UCd8Azl-iVV84GiN_np1cDwQ.

10 months ago

In this video you can see how to make a night light with your own hands from the simplest and most affordable things!

1 years ago

How to make an incredibly cool night light with your own hands from a garland and a light bulb. Other materials on our website...

3 years ago

DIY 3D LED NIGHT LIGHT 220 Volt from a plastic bottle. Homemade products Master's Secret. Original design...

4 years ago

Let's decorate the children's room with a night light. We make a night light with interchangeable shadows from cardboard with our own hands.

3 years ago

I love all kinds of manipulations with garlands! This time I will show you 2 ideas for decorating a room, tell you how...

1 years ago

In this video I will show you how to make a night light with your own hands. Its advantage is that it runs on batteries and...

11 months ago

Subscribe to the channel: http://bit.ly/2wjLewP Do-it-yourself desktop organization - 9 ideas: https://youtu.be/ghxWglSDiBU?list=PLJTrP...

9 months ago

A unique and beautiful DIY item that will decorate any interior! I present to your attention...

11 months ago

You can quickly and quite easily make a night light for children using cardboard, paint, glue and LED...

3 years ago

In this video I will show you how to make a night light from a garland and polystyrene foam with your own hands at home)))

1 years ago

A self-made LED tree with your own hands. How to make yourself. Very simple How to make an LED flowering lamp at home...

4 years ago

In a couple of minutes you can make beautiful lamps from glass bottles and garlands. My page http://vk.com/v...

2 years ago

In this video I will show you how to make an LED tree at home with your own hands with minimal...

12 months ago

How to make a night light. Glowing night light. Magic lamp. How to make a night light with your own hands. Master class...

3 years ago

How to make a night light with your own hands from paper? Today we will show you how to make a lamp yourself in an unusual...

2 years ago

DIY flashing bar made from an old garland.

3 years ago

cool lamp made of interior glass and New Year's garland. gift for daughter's March 8th. very much...

2 years ago

In this video, Brother and I show you how to make a cool battery-powered lamp out of wood with your own hands....

4 years ago

To make such a lamp, you will need a garland, an empty coffee can (we turned it upside down...

videobomba.net

DIY New Year's lamp - 20 photo ideas 2018

What, besides the Christmas tree, creates the atmosphere of the winter holidays? Of course, Christmas lights! It is they, flickering with warm lights, that bring a note of joy and anticipation of a miracle. Nowadays there is a huge selection of unusual models in stores, but the most exclusive ones are those made by yourself. We have prepared some ideas for you.

Threads and ropes

An amazing idea for making a light mat for those who knit. A regular single crochet stitch, inside there are plastic pieces with LEDs. You definitely can’t buy this anywhere!

Wrap string or thread around several balloons. The threads must first be soaked in PVA glue. When the product hardens, remove the balls. Insert battery-powered or mains-powered lamps through the holes between the threads. New Year's mood is guaranteed!

These New Year's lights in the shape of clouds are made of cotton wool and threads (battery-powered garlands are hidden inside). Perfect for decorating a child's room.

The dyed gauze and the garland turn... into an unusual and unique decoration.

Christmas lights made of paper

Do you have a simple LED garland? Decorate it and turn it into a cozy lamp for the New Year holidays. You will need:

scrapbooking paper;
plastic cups;
glue;
and some time.

You can transform an ordinary garland using origami paper lanterns. Such a lamp will provide a diffused, cozy, warm light.

For a children's New Year, a lamp in the shape of bright candies is suitable.

You can create such a shimmering masterpiece from crepe paper.

Ordinary lace napkins can turn into a wonderful New Year's wreath.

Festive lamps in the interior

Capture the story of the past year in photographs illuminated by the twinkling holiday lights.

Wine bottles filled with LEDs look truly magical!

A compact and unusual garland Christmas tree is an excellent solution for small apartments.

Even an ordinary vase filled with balls and LEDs can be the heart of the New Year's table.

Create, invent, light up the lights! After all, the New Year is the time for miracles!

new-year-party.ru

Night light made from old garlands

Today, there are many original master classes on assembling beautiful lamps for lighting a children's room and bedroom. Some models of homemade nightlights can be assembled from scrap materials in no more than an hour.

Let's get started.

Materials:1. Old garlands2. Board 10 by 10 cm.3. Glass jar 0.4 l.4. Power supply 12 V, 1.5 A

Tools:1. Drill2. Drill 4 mm.3. Screwdriver4. Glue gun5. Soldering iron (solder, flux...)

To begin with, we will cut three light bulbs of different colors from the garlands, in my case they are: red, yellow, green.

Let's take a board and clean it with sandpaper on all sides.

If you wish, you can varnish the board, which is exactly what I did.

Next, we attach the lid from the jar to the board and screw it onto two self-tapping screws, as in the photo. Then we drill a through hole with a 4 mm drill in the middle of the lid.

For stability, I made the legs from hot glue.

We take the light bulbs and glue them to the lid itself in the shape of a triangle, as shown in the photo. Shorten the wires slightly. We degrease the lid in advance using alcohol.

We insert the power cable from our unit into the pre-made hole. And we solder all the wires.

Here is the connection diagram itself, resistors are NOT NEEDED.

We screw the jar into the lid and get a table night light for your children.

Become the author of the site, publish your own articles, descriptions of homemade products and pay for the text. Read more here.

usamodelkina.ru

How to make a lamp from a garland with your own hands?

The garland, which is most often used to decorate the New Year tree, can be used as a component for the manufacture of a lighting device. A DIY garland lamp is easy to make.

To make a lamp you will need a garland, a plastic lampshade and a stand.

At the same time, the lighting in the room will be soft. This lamp can be used as a night light. The designs of such homemade lamps can be varied depending on imagination and source materials.

Lamp made of disks and garlands: production

The following materials will be required:

CDs or DVDs that have no graphics on both sides;
garland for 15-20 light bulbs;
glue and a gun for applying it.

To attach the disks you will need a glue gun or wire.

After all the holes are filled with light bulbs, you should glue the last part of the lamp cube. The light bulbs left for this purpose are threaded into the last disk.

After the structure is installed on the stand and the glue has completely hardened, the lamp is ready for use.

Lamp made of plastic packaging and garlands

Power supply diagram for a garland in a lamp.

In order to make this model, the following materials and tools are needed:

The basis. It can be used as a plastic bottle of any size or a plastic packaging box of various shapes, for example, a pyramid-shaped candy box.
A garland, the number of bulbs in which depends on the size and shape of the chosen base.
White paint. It is advisable that the paint be in a can. This will allow it to be evenly distributed over the entire surface in an even layer.
Soldering iron with a sharp tip (or electric drill and drill bit diameter).
Construction knife.

After the processing of the grooves is completed, you can begin painting. The base needs to be painted several times so that a uniform white color is formed over the entire surface.

After the paint has dried, you can place the light bulbs in the holes.

dekormyhome.ru

Homemade night light “cherry blossoms” from a garland

You can make a beautiful glowing cherry from inexpensive scrap materials. All you need is a little time and ready-made components.

Step 1: Materials

White LEDs from New Year's garland
Tissue paper of different colors (shades of white and pink are suitable). You can use it from gift wrapping if you have some in stock
A sprig of artificial flowers from a florist shop
Sand or gravel (small pebbles are fine)
Wires and bent cable ties
Glue stick, PVA and clear tape
Floral ribbon in dark color
Pliers
Scissors or other similar cutting tool

It is important to know that in the vase we will need to cut a hole at the bottom to connect the wires.

Step 2: LEDs

We trim artificial flowers, leaving only the necessary branches. Attach the LED wires using bent cable ties.

The power source (several batteries) should be located at the bottom. Try to distribute the LEDs across all branches.

Step 3: Tissue Paper

In our case, we used 2 layers of white and 2 pink tissue paper. You can make more than 4 levels using different colors.

We cut out squares from these 4 layers with sides of 7.6 cm. Each of them is needed for a separate LED.

Step 4: Cherry Blossoms

Fold each square in half. Bend the half into a cone, as shown in the figure. Align the edges.

Using scissors, cut a semicircle at the top of the cone, forming a flower. Use a glue stick in the center to connect all 4 layers. Use scissors to punch a small hole in the center.

Step 5: Branches

If you are using a real rather than an artificial branch, then it is better to sand it with sandpaper and glue the necessary small branches, if suddenly there are very few of them.

We plant our processed flowers through the center onto branches with LEDs. We fix them with transparent tape. Then add glue. When it dries, give the flowers a realistic look by slightly fluffing the petals.

Step 6: Tape

We wrap the entire branch with floral tape, including areas with wires all the way to the power source.

Step 7: Completion

Place the finished branch along with the batteries in a vase and start pouring gravel inside. Prime the entire power supply, but make sure there is clear access to the switch.

As soon as the batteries run out, you will have to empty everything and do step 7 again.

Feb 2, 2016Gennady

rukami.boltai.com

How to make a night light with your own hands at home?

Modern night lights are convenient and ergonomic lighting sources. They complement the interior of any room well and can become a real decorative element. In a children's room, a night light will help the baby feel safe, and a hand-made lamp can also be presented as a handmade souvenir.

Benefits of a night light

The advantages of a homemade lamp can be considered the following points:

creating a special pleasant atmosphere on the eve of sleep;
the ability to navigate in the dark without waking up family members with the main light;
reducing children's fear of the dark;
energy savings;
adding decorative elements to the overall interior;
additional visual effects to develop children's imagination.

Night light starry sky"

One of the most current and romantic night light models, to one degree or another, imitates an endless cluster of constellations in the night sky. You can make such a light source yourself from scrap materials. It does not need to be connected to the network, because a regular flashlight with little batteries is enough.

To create such a night light, you need a glass jar with a lid of any size, thick foil, scissors, an awl, a small flashlight and any surface that is not afraid of damage, for example, a tray.

Draw a star map on the foil. You can arrange celestial objects schematically or following the real arrangement of stars. It all depends on your desires and level of effort. If you are making a similar night light for a child, you can limit yourself to the image of the constellations Ursa Major and Ursa Minor.
Place the sheet on a flat surface and use an awl to make holes. These will be the luminous stars.
Trim the foil so that its height matches the height of the jar. Roll the sheet into a tube and insert it into a glass container.
Place a flashlight at the bottom of the jar and turn it on. The walls and ceiling will immediately be illuminated by the beautiful glow of the night light.

There is another option to make a children's night light that imitates the night sky. It can be made from an ordinary tin can. Such a container should be cleaned, the label removed, painted in any pleasant color and several holes made with an awl. Inside the jar you need to put a flashlight, a garland or a lit candle. It is advisable to cover the edges of the jar with a plastic lid so that none of the family members are injured.

Lacy night light

This version of the lamp can be an ideal romantic gift or bedroom decoration. To make a night light with your own hands, as a decorative element and a light source, you need to purchase a lace fabric. It can have different colors and patterns, depending on your preferences. You will also need a dry and clean jar, scissors with thread, and a flashlight with batteries.

Wrap the container with lace so that it does not protrude beyond the edges and does not overlap the edges. Remove excess parts.
Sew the edges of the lace to create a sleeve that matches the diameter of the jar. You can work on a sewing machine or by hand.
Place the sleeve on the jar, place the flashlight inside and screw on the lid.

Lamp from a can

Using available materials, it is quite possible to build a large homemade lamp that can decorate not only a nursery or bedroom, but the entire room. To create such a miracle, you will need an original tin or plastic tea can. You also need scrapbooking paper, stationery cardboard, a paper knife, acrylic paints, glue, sandpaper, and masking tape. And since in this case we are making not just a night light, but a lamp, we need to prepare a light bulb socket, an incandescent light bulb itself, a power cord and a switch.

Cut out a sheet of scrap paper that can be used to completely wrap the jar. Please note that the bottom of the tea bag will be the top of the lamp.
Remove the lid from the jar, lean it against a piece of paper, trace it with a pencil and cut it out.
Connect the cut out template to the wrapped jar using masking tape. Trace a circle with a pencil.
Using your markings, cut out the window. Sand the edges with sandpaper.
Re-trace the oval template onto the cardstock. Draw stripes inside it and cut out some of them.
Glue the cardboard to the jar on the inside.
You can decorate the outside of the jar as you wish, using paper, cardboard, acrylic threads, lace, etc.
At the back of the lamp, cut a circle for the power cord. You need to make a hole in the lid for the cartridge.
Assemble a socket with a light bulb, a switch and an electrical plug into a circuit.
Place the socket in the jar, screw in the light bulb.
Assemble the lamp and check its operation by plugging it into an outlet.

Night light for a child

When creating a lamp for a children's room at home, the most important thing is to use your imagination as much as possible. In addition, you can involve your baby in creating a night light and combine business with pleasure.

Prepare a glass ball or spherical shade for the lamp. You will also need a large amount of tulle or tulle, glue and several lanterns, or better yet, a garland for the Christmas tree.

Cut out a large number of small circles from the fabric.
Take a dry and clean lampshade, gather circles of tulle or tulle into a “rosette”. Fix the fabric flower on the lampshade with glue, dropping just a little into the very middle of the rose. This way you will create a fluffy ball.
Place a flashlight or garland inside the lampshade. Show the result to your baby and watch his joyful reaction.

LED night light

To make an unusual and beautiful LED night light that can be placed in a nursery, you need to prepare a pair of transparent plastic tubes with unequal diameters. You will also need LEDs with the desired brightness and color range. Also prepare glass pebbles, wire, a larger cork, superglue, pliers and a board for the LEDs.

Bend the ends of the LEDs with pliers.
Connect all LED bulbs with a piece of wire in a parallel circuit, observing polarity.
Connect the ends of the wire to the board.
Check the working part of the night light, if the LEDs get very hot, add a resistor to the circuit.
Glue the tubes one into the other. Place decorative balls into the void.
Place the LED plug onto the tube. If the diameter of the plug is larger than the tube, make a seal from a leather belt.
The LED night light is ready, you can turn it on.

Safety of night lighting

As is clear from the above examples, there are a huge number of designer models of homemade lamps. There are different techniques for working with decorative materials to create a variety of lighting effects.

However, behind the beauty of the night light, you should not forget about the safety of yourself and your family. To this end, you should be especially careful when considering the power supply circuit for the light source.

Many home craftsmen believe that compact nightlights have minimal power and low voltage, which in itself should protect against problems. This is not entirely true. A voltage of 12 volts for a halogen light bulb or 3 volts for an LED power supply does not pose a threat to the human body. However, if a short circuit occurs, an electrical arc will form at the point of contact. At the same moment, a current will pass through the wires, which can heat the insulation to the point of fire. In this case, the power supply may operate in overload mode, but the shield will not react. That is why it is necessary to protect the wiring of such light sources with a fuse. After the electrical wiring at the output of the power supply is protected, you need to pay attention to the electrical safety of the board itself. It is enclosed in a reliable housing, which is especially important for lamps in children's rooms, where children may try to disassemble the night light.

How does a halogen lamp differ from an incandescent lamp?

Despite the huge range of lighting products available in electrical stores, many people still highly value hand-made products. Firstly, admiring your creation is much more pleasant. Secondly, handmade allows you to create original light sources that can rarely be bought for money.

The approach of the New Year holidays is associated with pleasant chores, including decorating the premises in an apartment or private house. To make the interior more attractive, we suggest you create a lamp from a New Year's garland with your own hands.

Ways to create New Year's lights from garlands

To make devices, you can use any available materials. The main thing is not to forget about fire and electrical safety rules. Below you can see the different lamp options. By following the specified sequence of actions, you will create your own work of art without any problems.

Lamp made of New Year's garlands in a glass bottle or jar

The bottle can be used to create a variety of New Year's lights, but the simplest method is to simply lay an LED garland inside a glass product. The main disadvantage of this method is that the wire will stick out from the neck. To get rid of this defect, you should drill a hole in a bottle or other selected container (this could be a glass jar or vase). The process is painstaking, but if you have a drill, then you won’t be able to find a better alternative.

Necessary materials:

glass bottle, jar, vase;
transparent electrical tape or tape;
a syringe filled with water;
drill with a special drill bit for glass.

First, decide on the place where the hole will be made, then wrap the bottle with electrical tape (duct tape). Several layers of protective material are required. The hole is best made at the bottom of the container. Mark the location with a marker and begin the drilling process, setting the drill to the minimum speed. Stop from time to time and spray the area under the hole with water from a syringe to cool the glass and prevent chips and cracks.

When the hole is completed, carefully sand the edges if necessary. For this purpose, the drill is equipped with a special attachment. Then all that remains is to remove the tape and use a cloth soaked in alcohol or nail polish remover. It will help remove any remaining traces of adhesive.

Further actions depend on the specific idea. You can create a New Year's lamp from one bottle, or you can make a huge installation from identical or different containers. Do not forget that the capacity is selected depending on the length of the LED garland or vice versa. You should not buy a garland for 200 LEDs if the selected bottle can accommodate flexible boards for a maximum of 50 bulbs.

Now thread one end of the garland through the hole and push most of the product inside, leaving the plug and wire outside the bottle.

To decorate the resulting lamp, you can attach pine cones with sparkles, multi-colored ribbon, rain, beads, and Christmas tree branches to the bottle. Additionally, you can use glass painting, depicting various New Year's motifs on the outside of the bottle, adding sparkles or other improvised means. Inspiration can be drawn from numerous pictures on the Internet.

As for creating a lamp in a jar, you need to proceed in a similar way.

Lamp made from CDs and garlands

To create such a lighting device you will need:

old double-sided discs of any format (CD/DVD);
a garland with a length of 20-30 light bulbs;
glue;
glue gun.

Before you start assembling a New Year's lamp from disks and garlands, you will need to create a structure of a certain geometric shape. This can be a cube or a three-dimensional polygon used as the base of the device. Apply a thin layer of glue to the surface of the disk and attach a second one to it. Glue the remaining disks together until you create the desired shape. One side of the cube should be unglued, which is important for further actions.

When you complete the process of gluing the disks, place the selected garland inside the geometric volumetric figure. The product must be placed so that the plug and controller for controlling colors are located near the left window formed as a result of the articulation. Some of the light bulbs need to be removed through the holes. In total, there can be from 3 to 5 such windows, which depends on the volume of LEDs.

Light sources must fill the holes completely to achieve the desired special effects. Leave the remainder of the garland that does not fall into the holes inside the cube, placing it evenly over its surface. The outer bulbs need to be pulled through the last side, which will be formed as a result of gluing the last disk.

To make it convenient to install light bulbs in the holes, you can fasten them with adhesive tape (insulating tape). Glue and sealant will allow you to fix the formed group of diodes. After filling each hole with the required number of bulbs, replace the last side of the geometric figure. You need to thread the remaining light bulbs through the last disk.

Another disk can become a stand for a New Year's lamp. Use glue and secure the geometric figure, leaning it against the future base with its edge. As a result of these actions, the lighting device will be as stable as possible. Remember to hide the plug and controller, so make sure they are at the bottom when gluing to the stand. There is no need to glue these elements. Wait for the glue to polymerize, then check the functionality of the lamp.

Lamp made of plastic packaging and garlands

To make the lamp you will need the following materials:

a plastic bottle or box of any size and shape from which the base of the product will be created;
a garland for a certain number of light bulbs (the number directly depends on the dimensions of the selected bottle or box);
white paint in a can for uniform application over the surface of the device;
soldering iron or electric drill with a drill of the required diameter;
construction knife.

Before starting work, apply markings to the surface of the base. LEDs can be arranged symmetrically to each other or one per hole. You can create various designs from diodes in the form of a Christmas tree, a snowman, Santa Claus or the Snow Maiden. Make a small slit in the bottom of the bottle or box. It will be needed to thread the wire with the plug and the control unit - a necessary element for the operation of the garland in different modes.

Ideally, you should use a soldering iron with a sharp tip. This will make it much easier to make neat holes in a plastic bottle or box. If the quality of the plastic does not allow making holes and when using a soldering iron the integrity of the product is compromised, then you will have to use a drill with a suitable drill bit. Follow the markings and create holes using the tool that is suitable for a particular case.

Carefully inspect the bottle or box, examining each hole. If you find sharp edges or see that some corners of the plastic are turned inward or outward, use a utility knife and carefully cut off the excess pieces. Be patient and take your time so as not to damage other parts of the workpiece.

Having completed the steps associated with processing the grooves, pick up a can of paint. Apply several coats of paint correctly to the base of the product to ensure a uniform white color over the entire surface of the bottle. Wait for the paint to dry, then place the light bulbs in the holes. To make it more convenient, start the procedure from the top of the bottle.

When you install the LEDs and carefully place the plug with the control unit in the pre-prepared slot, close the base with the lid. Now you can freely move the product around the room and use it wherever you want. The lamp can be supplemented with plastic cups with holes made and individual lanterns installed.

New Year's house made of garland and corrugated cardboard

Corrugated cardboard will serve as the main material for making the New Year's House lamp. In addition to this, you will need a battery-powered garland, PVA glue, clean paper sheets, plain cardboard, acrylic paint and a sharp paper knife.

First, a template is made that will be used to cut out individual parts of the future house. Draw the necessary parts in accordance with the pre-calculated dimensions and cut them out using a stationery knife and a ruler (for convenience). As a result, you should receive several parts for framing, a back and a main wall on which the garlands will be attached.

Inspect the existing garland and measure the diameter of individual light bulbs in order to make a corresponding hole in the main wall of the future house. For example, if there are 12 LEDs on a garland, then they can be arranged either symmetrically or in a checkerboard pattern.

Mark all the points where the light bulbs will be located, then cut a hole on the template using a knife. Next, attach the template to the main wall and draw these holes using a marker, and then cut out with a knife. These manipulations with the template will allow you to avoid erroneous actions and damage to the base material. To give the holes a perfect round shape, insert a round pen or pencil of the appropriate diameter into each hole, and then spin the object.

Now you need to glue the four frame parts together and hide the wavy surface of the corrugated cardboard in the inside of the house. Cut out thick strips from clean paper sheets that will match the width of the future product. Glue them with PVA, then connect this part to the main wall, where there are already holes. Turn the house over and glue the remaining frame pieces to the back side. As a result of these actions, you will receive the basis of the future lamp.

Mask all other unevenness in the same way, but this time use a sheet of regular cardboard. Measure the width and cut strips of the desired size. Don’t rush to cover the house with them, but first secure its upper part using a piece of thick paper. Glue the cardboard strips, starting from the bottom and ending with the walls.

Next, you need to paint the house with special acrylic paint to make it monotonous and give the appearance of a solid structure. Once the paint has completely dried, begin placing the bulbs by threading them through the holes. It's best to move from top to bottom. To get rid of protruding wires, use tape. Cover the back wall and install the switch. It can be glued with special glue or secured with double-sided tape.

The lamp is ready! Check its functionality. You can leave it in the same color, or decorate it with paper figures in the shape of Christmas trees, snowmen or snowflakes. Beads and “rain” will not be superfluous.

New Year's garland on a branch

First, find a suitable Christmas tree branch on which you will attach the garland. You can use thin wire to secure the light bulbs. If you don’t have one at hand, then buy sparklers. Their metal rods bend well, making them easy to use. To remove the incendiary mixture, you can clean the sparklers with a regular knife.

When choosing a garland and a Christmas tree branch, make sure that the length of the LED product is 2 times the length of the branch. Each branch will be wrapped in a garland 2 times: first you will move from left to right, and then from right to left. By the way, the branch needs to be prepared in advance, since it will take some time to dry. Alternatively, you can cover the branch with acrylic or oil paint in your desired color.

If you want to create a more original product, we recommend additionally creating a frost effect. Regular toothpaste diluted with water will do. You should end up with a mixture that has a consistency similar to kefir with bubbles. Cover the branch with it and wait until it dries. The result will be truly fantastic!

Important. It is absolutely not necessary to use a Christmas tree branch. A branch of any other tree, such as an apple or cherry tree, will do. The main thing is to choose a strong and dense workpiece that will not break during operation.

The lamp can be created from either one or several branches. Let's consider the second option, since it is much more complicated than the first. To begin, secure part of the garland to the first branch. The garland needs to be laid out around the outline of the branch lying on the table. For convenience, move from left to right clockwise, starting from the base, following to the top and returning back.

In some areas, secure the LED strip with wire, cutting off the excess ends with wire cutters or pliers. Place the second branch on the table and arrange the garland around it. If the selected branch has small branches, then be sure to place the garland along their contour in the same way as you did with the base of the trunk.

At the end, you should have a 50-60 cm piece of free wire left in order to freely connect the product to the outlet. In the lower part, next to the base, you need to fold the bends of the wires and tie them into a tight bundle. The resulting bouquet can be placed in a vase or simply placed on a shelf. Ideally, the lamp should be hidden under a glass form.

When choosing a black or white garland, be guided by the color of the branch. If it is dark, then it is best to use a black LED strip. If you covered the branch with a toothpaste solution, then a white product will do.

The article did not list all the varieties of New Year's lamps that you can make yourself from an LED garland. There are a huge number of options, but it is not at all necessary to choose a specific one. You can use the information received only to modify your own, original product. Give free rein to your imagination, and you will definitely succeed!

Every year we buy new decorations for the Christmas tree, occasionally we update the garlands... And now - a bunch of New Year's decorations have already accumulated, which it would be a pity to throw away and there seems to be nowhere to hang them on the tree... If you still have a transparent glass vase, then you can make from all this is a New Year's lamp.

Materials:

Glass transparent vase (small aquarium)
Garland
Christmas decorations
Mushura
If available, branches from an artificial Christmas tree

I saw the idea for a lamp made from a vase somewhere on the Internet. And then I just remembered...

Wash and wipe the vase dry.

Put some tinsel on the bottom

Lay the end of the garland in a circle

Let's start putting away the toys.

It would look more original if the toys were laid out in layers, i.e. in the first layer - identical ones, in the second - different toys, but also identical. Or put fir branches as the second layer, and toys again as the third.

Unfortunately, I didn’t have any branches - a piece of the top of the tree cut off can’t be counted - so I had to limit myself to tinsel and toys

We also place a garland in a circle on the layer of toys and decorate it a little with tinsel on top. My tinsel is long, so I cut off very short pieces - about five centimeters

Main: Do not compact the layers!!! We place it loosely so that there is air circulation.

Fill the vase almost to the very top. The garland is completely placed in the vase - only the switch for the flashing modes of the light bulbs remains outside. We place it on the back side of the lamp.

Decorate the top with the last layer of tinsel and close the switch

Put it in a suitable place and get in the pre-holiday mood!

And this is how it shines in the dark

PS. After the publication of the article, many questions arose about the fire hazard of such a structure. I deliberately kept the lamp on for about 6 hours. During this time there were no signs of overheating. There is quite a lot of empty space in the lamp - it is decorated with tinsel - so there is good air circulation there.

Again, the answer is logical: the garland on an artificial Christmas tree doesn’t scare you, does it? But she lies right on the Christmas tree branches, also in contact with toys and hung with tinsel? In addition, now you can safely buy LED garlands that do not heat up at all and do not pose a danger.

The garland, which is most often used to decorate the New Year tree, can be used as a component for the manufacture of a lighting device. A DIY garland lamp is easy to make.

To make a lamp you will need a garland, a plastic lampshade and a stand.

At the same time, the lighting in the room will be soft. This lamp can be used as a night light. The designs of such homemade lamps can be varied depending on imagination and source materials.

Lamp made of disks and garlands: production

The following materials will be required:

CDs or DVDs that have no graphics on both sides;
garland for 15-20 light bulbs;
glue and a gun for applying it.

To attach the disks you will need a glue gun or wire.

After all the holes are filled with light bulbs, you should glue the last part of the lamp cube. The light bulbs left for this purpose are threaded into the last disk.

After the structure is installed on the stand and the glue has completely hardened, the lamp is ready for use.

Lamp made of plastic packaging and garlands

Power supply diagram for a garland in a lamp.

In order to make this model, the following materials and tools are needed:

The basis. It can be used as a plastic bottle of any size or a plastic packaging box of various shapes, for example, a pyramid-shaped candy box.
A garland, the number of bulbs in which depends on the size and shape of the chosen base.
White paint. It is advisable that the paint be in a can. This will allow it to be evenly distributed over the entire surface in an even layer.
Soldering iron with a sharp tip (or electric drill and drill bit diameter).
Construction knife.

After the processing of the grooves is completed, you can begin painting. The base needs to be painted several times so that a uniform white color is formed over the entire surface.

After the paint has dried, you can place the light bulbs in the holes.