Decorative box for pipes in the bathroom. The best solutions for making a pipe box in the bathroom. Using polystyrene panels as a box

A modern plumbing room has many communications intended for water supply, sewer system and heating. All of them significantly spoil the interior of the room, which makes it necessary to cover them. The ideal solution for such camouflage is considered to be a pipe box in the bathroom, which is a simple but quite functional design.

Specifics of the pipe box

Bathrooms and toilets have a characteristic microclimate and contain various utility systems for common use. Meters are usually installed on these pipes to control the flow of all types of water and shut-off valves. All this requires periodic maintenance, which includes checking the integrity of the connections, cleaning the filters and repairing any faults.

There are various ways to aesthetically close communications. One of them is hidden wiring, in which special grooves are created for pipes in the walls, but this option cannot be considered as universal due to a number of disadvantages. Installing the box will provide access to technical systems, it can be completely collapsible or have special doors.

Design requirements

There are certain requirements for the box masking the pipes, the main ones are as follows:

1. 1. To avoid cluttering the room, the decorative box should occupy a minimum amount of space, since the sanitary room has a small area. However, during the manufacture of the structure, the required distance of its elements from the pipes must be strictly maintained, which must be at least three centimeters.
2. 2. Providing access to communications without any difficulties. The structure of the box should allow the specialist to freely carry out the necessary operations with the elements of the engineering system. For these purposes ideal solution there will be a removable structure, otherwise the installation of numerous doors will be required.
3. 3. Safety that prevents physical injury to a person during operation.
4. 4. Harmony with the decoration of the room, the ability to fit into the overall interior.

Taking into account the specific microclimate of the bathroom, the decorative box should be moisture resistant.

Advantages of a camouflage box

When decorating modern bathrooms, a box is often installed to cover the pipes. Its popularity is due to a number of advantages:

1. 1. Aesthetic appearance thanks to the quality of the materials used for production.
2. 2. Ease of assembly, allowing the construction of the system not only during overhaul, but also cosmetic, since it is possible to install the structure on top of the completed finishing.
3. 3. Providing unhindered access to the engineering system, allowing to monitor its condition, carry out repair work when necessary and record meter readings.
4. 4. The possibility of productive use of bathroom space by combining the structure with a toilet installation, various shelves and other elements.

A carefully made box can be both functional and aesthetic, becoming a decoration for the room.

Options for obstructing communications

You can hide pipes in the bathroom different ways, the most popular of which are the following:

1. 1. Boxes in the form of cabinets, a similar solution is usually used for systems with a vertical arrangement, such as risers. The design provides full access to the pipeline, meters and other elements. Its advantage lies in the ability to place shelves and various devices for storing household items inside it. This allows you to effectively use the space in the bathroom and toilet.
2. 2. Boxes like partitions, installed along the entire length of the room and to its entire height, thereby making a certain space separate. The disadvantage of this option is that it reduces the area of ​​the room, but at the same time its appearance becomes ideal due to the complete hiding of all engineering systems. Such partitions are especially suitable for spacious rooms and toilets with wall hung toilet, since along with communications the installation is also masked.
3. 3. Compact box located around the pipes. Such designs are used quite often due to the fact that they do not take up space and give the room an aesthetic appearance. These systems can be located both vertically and horizontally, adjacent to the ceiling or floor.

Types and characteristics of material

To make a decorative box that masks pipes, you need to select the appropriate material, which must meet certain requirements. The main ones are resistance to high levels of humidity, low weight and low thickness. Also, the structure must be made from components that are environmentally safe.

Of all the materials offered by the market, moisture-resistant plasterboard and plywood, MDF or plastic meet these criteria. PVC panels and gypsum boards are especially popular.

PVC panels

Working with this material is the simplest option for closing pipes. His positive sides are as follows:

1. 1. A box for masking PVC pipes does not require additional work related to finishing.
2. 2. If dismantling is necessary, all components are preserved, which is especially important for pipelines with fitting and threaded types of connections.
3. 3. Easy installation, completely doable on your own.
4. 4. Non-susceptibility to deformation and easy care during operation. The material is flexible and reliable, if damaged individual panels each of them can be easily replaced.
5. 5. Insignificant thickness, contributing to the compactness of the structure.
6. 6. A product made of polyvinyl chloride can withstand repeated assembly and disassembly and provides the opportunity to store various accessories inside, creating all the conditions for this.

U PVC material there are not only advantages, but also weak sides. One of them is low resistance to temperature changes. The material has a specific odor that cannot be eliminated. Plastic has the ability to disintegrate over time, releasing harmful components into the air during this process.

Moisture-resistant drywall

Compared to PVC panels Drywall has many more advantages. The main ones should be highlighted:

1. 1. Easy installation. The GKLV material can be easily fixed on a base made of galvanized profiles, which allows you to create a box for pipes of any configuration and size. Carrying out such work does not require special skills or the use of complex equipment.
2. 2. Plasterboard sheets are lightweight, which eliminates additional load on structural parts and requires the use of weightless galvanized elements to hold them.
3. 3. The flexibility of the material, which makes it possible to give the product the desired shape. To do this, one of the sides of the gypsum board is moistened and trimmed.
4. 4. Smooth surface, simplifying the process decorative finishing boxes In this case, additional leveling by plastering along beacons will not be required.
5. 5. The texture of drywall allows for decoration various types finishing materials. Typically, tiles are used for this purpose, but you can decorate the pipe box made of gypsum board with clapboard, cover it with wallpaper, or simply paint it.
6. 6. Fire safety of the material due to the fact that it consists of sheets of cardboard and hardened gypsum, which are not prone to easy ignition. In case of contact with open fire, drywall does not emit toxic substances that have Negative influence on human health.
7. 7. Environmental safety due to zero formaldehyde emissions from plasterboard. The material will not cause harm both during installation and during subsequent operation.
8. 8. Affordable price, making the material accessible to every consumer.

It is important to remember that the pipe box must be made only from moisture-resistant plasterboard, colored in green color. This option well tolerated increased level humidity and is designed for use in such conditions.

Manufacturing and installation

Before proceeding with the construction of the system, it is necessary to carry out preparatory work. When laying new pipes, it is recommended to design them with as few connections as possible. Before installation, it is necessary to carefully check the pipes for various damages leading to leaks.

The material for making the box should be ideal for sanitary facilities. After taking the measurements required for subsequent work, a preliminary drawing of the future structure is drawn up. It must provide free access to all devices and elements on the pipeline.

Preparation of tools and auxiliary materials

The design of a box for masking pipes in a bathroom includes a frame, lining and fasteners. In turn, the frame can be made either from metal profiles or from wooden beams. Due to the fact that wood is significantly inferior to metal in terms of durability, it is recommended to give preference to the second option when choosing.

As fastening material it is necessary to prepare:

• dowels for mounting the frame to the wall;
• self-tapping screws for wood or metal, with the help of which the frame is assembled;
• self-tapping screws used for working with cladding material.

Before making a system for masking pipes in sanitary rooms, you should ensure that you have the following tools:

• roulette;
• square;
• building level;
• screwdriver;
• perforator;
• plane;
• scissors for working with metal or a hacksaw;
• knife with a sharp blade;
• UD and CD profiles.

Measuring operations

Before construction begins, the location where the structure will be placed is specified and all necessary measurements are taken. This will prevent amendments during installation work, which are always accompanied by certain difficulties. It is almost impossible to change the size of an already prepared element without affecting other parts of the structure.

At this stage, the location of inspection doors or removable parts of the box is immediately thought out. It is recommended to include the thickness of the finishing material in the drawing where the dimensions of the system will be indicated. Marking for the construction of the frame begins immediately from the floor, while the dimensions between the walls of the structure and the pipes are strictly maintained, which should not be less than three centimeters.

After the contour of the box has been determined, it is applied using a plumb line to areas of the ceiling and walls that will come into contact with this structure in the future.

Assembling the frame for the box

The fittings around the pipes are usually made of galvanized profiles or wooden slats with excellent moisture-resistant characteristics. The latter option requires mandatory treatment with antiseptic agents. The frame parts are connected to each other using a cutter or self-tapping screws. Additionally, you will need dowels and special screws. The work consists of several stages:

• the profile is installed on the walls;
• racks are installed that will act as the front edge of the box;
• guides are installed on the ceiling and floor.

The length of the racks can exceed one and a half meters, in which case jumpers must be installed between them, which may still be required if the frame width exceeds twenty-five centimeters. The distance between these structural elements should be no more than one meter. Jumpers will add the necessary rigidity to the structure.

When making reinforcement from wood, the cut areas are treated with special construction mastics. This prevents the process of rotting and deformation due to temperature changes and fluctuations in humidity levels.

Sheathing process

After completing the cutting of all required elements, sheathing is performed. It is not recommended to cut from fragments of material; it is best to use whole pieces. This will minimize the possibility of distortions and discrepancies in sizes. When cutting, you need to look beyond the edges of the elements, which should not extend beyond the frame parts. Ideally, all elements should match each other. The cut out front face of the structure should cover the side parts.

Installation of the cut material to the reinforcement posts is carried out using self-tapping screws, the distance between which should not exceed two and a half centimeters. This will give the box rigidity and strength and eliminate the need for additional jumpers.

To control individual sections of the communication system, special holes and doors are provided in the casing material. They can be purchased ready-made in specialized stores or made with your own hands. To prevent inspection doors from spontaneously swinging open, magnets or various locking parts, such as latches, are installed on them.

During production, completely collapsible design sheets of finishing material are attached using self-tapping screws to the very edge, and are not covered with anything during the final finishing work. Only plastic corners or plinths are installed that can be easily disassembled if necessary.

A plumbing box (in other cases it is called a plumbing cabinet) is used in most panel and brick series modern houses(since the 70s).

He is also always present in monolithic houses, however, in fact, in most cases it is not there and the owner is asked to build it according to the “bricks” laid out on the floor of the room.

It is an enclosing structure (with access hatch) for hot and cold water supply risers, as well as a sewer riser.

The main information that the customer should have regarding the installation of a plumbing box is the understanding that the area inside the box refers to the common area of ​​the house and is not included in the area of ​​the apartment.

Based on this, the only thing that is possible during repairs is to remove the old plumbing box and build a new one along its border. modern materials with the obligatory installation of a hatch for access to utilities.

Materials used:

• Moisture-resistant plasterboard with ceramic tile lining;
• Thin tongue-and-groove blocks;

Measures for remodeling the plumbing duct:

• Dismantling the plumbing box (building a new one) with a subsequent increase in the original dimensions.

Application:

Besides direct use(fencing of water supply risers) plumbing box is often used as a structure for embedding a toilet installation.
Also, an enlarged sanitary cabinet can be used to accommodate an electric boiler. for the purpose of heating water during the summer shutdown of hot water supply.

What are access hatches and why are they needed:

Plumbing duct access hatches come in a variety of shapes.
The main thing is that the hatch must have sufficient dimensions to inspect the condition of risers, taps and water supply meters, as well as carry out current repairs utility risers. Above we provided a link to an article about access hatches.

Touching the plumbing box entails work on new waterproofing of the bathroom floor. Since on plumbing box, as on the walls in the bathroom, waterproofing must be installed, which is necessary as protection against possible leaks between floors. It is installed on the plumbing box, as well as on the walls in the bathroom to a height of 15-20 cm.

In new monolithic houses, the developer shifts the work of installing plumbing ducts to the owner (but does not forget to mark them with a dotted line on the BTI plan as completed). As a result, future owners will have to build a plumbing box in the dimensions marked on the floor plan with the installation of an access hatch. And if this box is not “physically” present when the apartment is rented out, this does not mean that it can not be built, or built in smaller dimensions, it just means that the developer saved on materials and gave this “honorable” responsibility to the owner himself

In the end, we will answer the main question that worries the owners:

Are there still cases in which a plumbing duct can be partially dismantled?
- Eat.

But it's quite difficult. As we have already mentioned, the plumbing duct belongs to the common area of ​​the house, which can be affected if technically possible, subject to the consent of 2/3 of the residents of the house.
This means that if you have a large plumbing box, and engineering Communication“huddled” somewhere in a corner, then theoretically it can be reduced in size. “Only” it is necessary to collect the signatures of 2/3 of the residents of the house that they are not against this event, to back it up with a seal management company and submit the protocol along with the design documentation for consideration to the housing inspectorate.

Under this condition, she will agree to dismantle and partially dismantle the plumbing duct. Of course, in words the path is clear and seemingly simple, but in practice, it’s not that it’s difficult to get the consent of 2/3 of the house owners, it’s difficult “in principle” to find them, which leads to the fact that very few people dare to start this path.

From practice: One of our cases involved dismantling a plumbing duct.

Initial data - new building, monolith, apartment on the middle floor. The customer’s BTI floor plan shows a plumbing box, in a strange place and what’s most strange it is shown then it is shown , but in it NO engineering communications.

It’s just that on the BTI plan there is a square that appeared for no apparent reason, in an illogical place, and it needs to be fenced off with a square simply so that this area does not become part of the area of ​​the apartment (after all, this is a common building area).

The customer, of course, really did not want to do this - after all, in his new monolith, the design solution was so well thought out, and this square did not fit into it at all, it was not taken into account, and we well understood that it really did not belong there.

An "investigation" has begun. It turned out that the new building consists of 8 identical sections. And in one of the sections (not this one), the developer provided another communications riser in this very place. When BTI measured the area at the end, it was lazy, measured only one of the sections (namely the section with the box) and “applied and projected” this plan onto the other sections, without even going in and measuring them (the house looks the same). (But this was said later and in a whisper).

Officially, they categorically refused to acknowledge this mistake. As a result, the remaining seven sections turned out to be potential “violators”, because none of the owners were eager to allocate, for some unknown reason, in an unknown place, a “deaf” square meter of an apartment.

Of course, it was possible to “fight” to bring up the developer’s archives, go around, prove it, but it would take a month or two or three, renovations could not be started without permission, and the owner’s thoughts were already living in the renovated apartment, and the mortgage was “dripping” and it seemed to us an easier way working with the management company. Moreover, she turned out to be surprisingly sane and understood the absurdity of the situation.

The management company engineer called the owners, they came and each owner allowed all other owners to dismantle the box. This paper remained with the management company to issue copies to others, and we submitted ours to the housing inspection along with the kit project documentation and received permission for redevelopment.

A typical example of how owners touch plumbing ducts:

Below we show an example of touching the plumbing duct of one of our recent customers:

At the beginning, we did not have clear initial data, that is, BTI documents, there was only a photo, but when looking at the apartment after the redevelopment (right photo in the top row), an initial assumption appeared that not everything was “smooth”.

A little later, the customer sent us a photo before the repair ( left photo- apartment “in concrete”) and BTI documents. And after analyzing these documents, everything immediately became clear.
In general, based on 95 percent of our experience, we already assumed that something similar would happen, but it was not superfluous to be confirmed.

If we look at the left photo, we will see that the boundaries of the plumbing box are “clearly” laid out in “bricks” along the floor. That is, they are clearly defined and the dimensions of the box cannot be changed.

And as we already know, a plumbing box is just a “cabinet with a door” and cannot be further “tuned.”

In this case, the customer:
not only reduced the size of the box, we reflected this in the bottom picture with the BTI plan,
so I built it into the top of the box open shelves , and also at the bottom safe between the pipes.

A combined photo, before and after renovation, in which something is placed in proportion.

Below on the BTI plans you can see how the box looked before the redevelopment, and how it looked after the redevelopment.

Pipes in the bathroom always interfere with the perception of its interior. In some cases, there is no other option but to make a pipe box in the bathroom to hide unsightly details of the furnishings. But this method of solving the problem has its own characteristics that it is advisable to keep in mind.

How to choose the right materials?

Making a box in the bathroom with your own hands is not technically difficult, but you should take into account the features of this room. High humidity and possible splashes on the walls dictate that the owner give preference to moisture-resistant materials. These include:

Having a low ability to absorb moisture, sheet materials are easy to cut and process. They can be decorated according to overall design bathroom, painting, tiling or plastering if necessary.

It is necessary to fasten the sheet material to the frame, so in addition to gypsum board or other sheets, you also need to select the material for the guides. It is most convenient to use ready-made profiles for installing drywall. This metal constructions, durable and light at the same time. They are easy to cut and attach to each other and walls. Installation of sheet material is carried out using self-tapping screws.

An alternative to profiles can be wooden block. The 3-5 cm thick planks do not weigh down the structure and are easily connected with self-tapping screws. Their the only drawback may be susceptible to rotting upon contact with moist air bathroom

How to prepare a workplace?

Before you make a box in the bathroom with your own hands, you need to determine whether it will directly cover the communications or cover the entire adjacent wall. In each individual case, any option may seem preferable. Each of them has its own characteristics:

To radically solve the problem, some place an entire storage system for necessary things in the space behind the panels. This bathroom box for pipes turns into a kind of shelving unit with doors.

How to make a box from plasterboard, panels, plywood or other material is a personal matter for each owner. In order to imagine the possibilities of each of the methods, you need to first draw a sketch and use it to draw a rough plan of the situation in the bathroom. Based on the drawings, the quantity is also calculated. necessary materials, taking into account the height of the room, the width of the box and the presence of additional parts in it.

After this, you can proceed to purchasing and preparing everything you need; you will need the following tools and materials:

• profiles (bar);
• self-tapping screws for connecting and fastening sheets or panels;
• dowels for attaching the profile to a concrete wall;
• hammer drill with attachments for drilling concrete and metal, with a screwdriver;
• a hacksaw for wood or metal, depending on the frame material;
• plumb line, level, tape measure.

Before installing the pipe box in the bathroom, you need to find out the state of the communications. IN closed space any minor leak may go unnoticed for some time until an emergency occurs. An undetected defect may result in the need for bathroom repairs in the future, so it is best to identify the problem early and fix it.

Marking the frame for the box

Most often, the sewerage and water supply risers are located side by side and run vertically in one of the corners. Therefore, you need to start marking the space for the box in the bathroom with your own hands from the ceiling. This will make it possible to subsequently lower the exact vertical to the floor and make the planes perfectly flat.

If you plan to cover the entire wall with panels, then near the pipes in the bathroom with your own hands you need to measure the depth of the space between the wall and the location of the profile for the gypsum board or bar. It is necessary to take into account that the guide must be at least 5 cm away from the communications. Remember the found distance in order to make a mark in the opposite corner. Connect the points with a straight line along the ceiling.

At two randomly selected points on this line, lower the plumb line to the floor. Place marks corresponding to the points selected on the ceiling. Draw a straight line through them on the floor.

It is advisable to perform the same algorithm of actions if the pipes run horizontally. Accurate markings will help make the frame for the bathroom box very neatly and without distortions. In this case, a line on the ceiling will not be needed, so it is better not to draw it, but to place marks near opposite walls. When lowering the plumb line, you will need to mark the points of the front edge of the box on the floor, and the junction of its edges with the walls - on them themselves. The height of the box is determined depending on the height of the pipes above the floor, taking into account a gap of 5-7 cm.

In order to mark the frame of a vertical corner box made of plasterboard in the bathroom, you will have to act a little differently:

• set aside the distance along the ceiling from one of the adjacent walls parallel to the adjacent one, taking into account gaps of 5-7 cm from the pipes to the guides;
• do the same from adjacent wall, at the intersection of the lines, place a point from which the plumb line will be lowered;
• Using this tool, mark the projections of 3 points (junctions to walls and intersections of lines) on the floor.

Drawing an angle using the marked marks is quite simple. You need to connect the junction point with the intersection point and repeat this from the adjacent wall. The resulting rectangle will be identical to the one drawn on the ceiling.

Frame installation

The marked lines indicate the location of the inner edge of the profile. Cut the material according to the measured lengths of the sides of the parallelepiped, which will serve as a box for pipes in a plasterboard bathroom. Attach the profiles on the ceiling, floor and walls with dowels into the pre-drilled holes. The frame slats need to be aligned according to the markings and additionally checked for their verticality and horizontality, eliminating defects.

The location of rigidly fixed parts will be different:

1. For a completely wired wall, install horizontal guides on the ceiling and floor. Then 2 verticals are attached between them on opposite walls. If it is necessary to build shelves inside this space, you will need to additionally install profiles on the wall being closed.
2. If you are making a horizontal box in the bathroom, you need to strengthen the planks with your own hands on the floor, on the wall above the pipe and on the walls adjacent to it (vertically and horizontally).
3. The vertical frame for the box in the bathroom is assembled with your own hands from racks on adjacent walls and squares on the ceiling and floor.

After the parts adjacent to the walls and ceilings have been secured, you can install connecting elements that form an angle or plane. In this case, for a vertical box, the same front post is installed, for a horizontal box, it is secured in the appropriate position. On a completely lined wall without internal space equipment, you will need to install several verticals with a step that will allow you to attach the panels used (gypsum plasterboard, plastic or plywood) along the edges and in the center.

To ensure structural rigidity, cross members are installed connecting long parallel profiles. Their location depends on the orientation of the box itself. In any case, the orientation of the crossbars should be perpendicular to the main guides.

Box lining

Depending on the location of the pipe box in the bathroom, the installation of the casing will differ in each case. This is dictated by the nuances of joining gypsum board or plywood panels. Assembly plastic parts It is produced using its own special technology.

For installation sheet materials on a frame made by yourself, you should cut them according to the measurements taken from it - this is the length and width of each flat part. To make a plasterboard box in the bathroom, it is advisable to use whole sheets so that there are as few joints as possible.

If the pipes have a fitting, tap or other place where a possible leak may occur, then a convenient hole should be provided in the wall plasterboard box. It will give access to a responsible place. In order to close it, a small secret door can be made. It is advisable to install additional crossbars along the edges of the hole.

GKL or plywood are attached to a completely sewn-up wall in the same way as during normal leveling: fasteners are screwed into the corners of the sheet, along the edges in increments of about 20 cm and in the center. In this case, the joint of adjacent sheets necessarily falls on the profile strip. The heads of the screws need to be recessed into the material so that they are not noticeable after finishing.

When covering a vertical frame that covers only the pipes, first install the side parts that make up the box in the bathroom made of plasterboard or plywood. Measuring and cutting must be done so that the outer edges perfectly match the profile angle. They can be cut off if necessary sharp knife flush with the corresponding plane.

The front panel must be cut so that it covers the edges of the side sheets. You can attach the gypsum board to the frame with special short self-tapping screws, using a screwdriver attachment for this purpose.

If the pipe is installed horizontally in the bathroom, you must first screw the vertical front panel onto the frame. After this, install the horizontal one so that it overlaps the edge of the previous one. This measure will make the plasterboard box for pipes less vulnerable to splashes when taking a shower and other hygiene procedures. You can tile gypsum board or plywood. The tile will reliably protect the material.

Plastic panels as cladding

Make plastic box for pipes in the bathroom it is much easier. Lightweight, moisture-resistant material will not require additional protection.

To make a box of panels, you can make it like this:

• install the starting profile on the guides, fastening with self-tapping screws;
• measure and cut the panel, insert into the profile, secure with screws;
• glue or screw the adjacent element to the corner profile and connect it to the installed PVC panel;
• attach the profile to the frame and assemble the other side.

You can purchase a hatch for PVC panels from construction companies. It will be required if it is necessary to make an inspection hole in the panel.

Currently, trade organizations also offer EPS panels that do not require the installation of a frame. They are fastened using an end strip installed on the ceiling and threaded legs that lift and fix the panel.

Video instruction

Communications are required in the bathroom. Open sewer and water pipes They don't look aesthetically pleasing. A box made of plastic panels. It looks great, can be easily dismantled if necessary, and provides access to all elements for maintenance.

Advantages of using a plastic box

Hiding unsightly details is very useful. This allows you to refine the interior of the room, depriving it of awkward details. If you hide everything that spoils the decoration of the bathroom, then it will be joyful and complete. She will become neater and more presentable. A box made of plastic panels will best solve this problem.

When constructing this finishing element, it is important to take into account many points and ensure that it does not interfere with the ability to take meter readings. Known situations require decisive action without delay; it is necessary to be able to quickly carry out repair work to eliminate the accident. Taking this into account, it is worth thinking about the versatility of the product being created.

There are various execution options. Especially often, eye protection is made of plasterboard; and are often used. These options are each good in their own way, but the last solution turns out to be more reasonable and effective. The question of how to cover the pipes in the bathroom with plastic panels is more relevant. This method is more justified and easier to implement.

His positive traits are as follows:

• A bathroom frame made of this material does not require further finishing.
• Easy to dismantle while preserving all components. This can be useful when using pipelines with fittings and threaded connections.
• Simple installation of the structure makes it a good decision. It is easy to build it yourself without using unavailable resources.
• High resistance to deformation and maintenance. The material has high flexibility and strength. The damage will not be fatal. Any panel can be easily replaced with a new one.
• The compactness of the design is achieved by the insignificant thickness of the material.
• A functional, convenient product that can withstand repeated assembly and disassembly, and can be stored inside various items and accessories, since there are all conditions for this.

Despite all the huge number of advantages, this solution demonstrates minor disadvantages, one of which is low resistance to temperature deformation. A persistent odor cannot be a virtue either. Plastic degrades over time, and the air contains some components of this decomposition that are undesirable.

Preparatory stage of installation

Be sure to check all pipes before installing the box!

Immediately before hiding the pipes in the bathroom, you will need to do some preparatory work. All pipes are carefully inspected. When found problem areas The defect must be eliminated while it is possible.

Advice! If new communications are carried out before installation, they should be carried out with maximum care with a minimum of complexity of connections. Any element can be at risk of breakdown, which may be accompanied by leaks.

1. The dimensions and shape of the product must be carefully analyzed. Masking can be done in several ways. In some of them everything is closed completely, in others you can limit yourself to only a part, which allows you to leave more free space and consume material in smaller quantities. When completely closed, it becomes possible to get extra bed for storing brushes, detergents and other substances.
2. After taking accurate measurements, you can create an accurate design drawing. In it, carefully work out all the details regarding the location of inspection hatches and their parameters. This will ensure unobstructed elements and counters.
3. When subsequently finishing the walls with tiles, the first step is to install a protective structure. Then the tiles will only need to be laid on open surfaces. This allows you to reduce ceramic consumption. According to the drawing, it is worth calculating the material consumption; its supply should be 8% higher than the calculated one.
4. For the case you will need to use sheet or rack panels. Installation will require metal profiles rack and guide types. Seam joints are supposed to be covered with skirting boards. Must have in stock silicone sealant, self-tapping screws, assembly knife, inspection hatches.

Features of frame installation

First, guides are placed on the walls adjacent to the corner. This must be done in compliance with the level. These profiles determine the size of the entire structure. For control, you can use a bubble or pipe level.

Important point! Fastening steel profile It will be more reliable if you attach it to the wall with dowels and European screws. For installation on tiles, you will need metal screws installed in the seams between the tiles. In this case, you can only install it on already dry tiles. It is important to twist the screws extremely carefully and carefully. If the self-tapping screw becomes jammed while rotating, the process should be stopped. The screw will not hold when twisted.

It makes sense to make the design more compact, since small space It is important to save money in the bathroom. For this reason, it is better to install guides closer to the pipes.

After installing the guides on the walls, you can begin to form the corner from the outside. A tight angle is required. Corner stand twisted from two guide-type profiles. In this case, the shelves are directed at right angles to each other. You can screw them together with self-tapping screws small size. Next, the resulting product is placed in place. For these purposes, the supporting profile type cd is cut into pieces corresponding to the length and width of the structure.

First, a corner stiffener is attached to one wall. The profile pieces are inserted into a guide mounted on the wall and the corner rib profile. Additional jumpers are needed in the middle; they will allow you to attach plastic panels. A building level must be used in the work; the box should not turn out crooked, it should look perfect.

How to sheathe the resulting frame with plastic panels

When the frame for the plastic box is completely ready, it can be immediately sheathed with plastic panels. You need to start by installing a starting profile. It is secured using self-tapping screws to one of the guides on the wall. You only need to attach it to one guide. If you attach the starting profile to two guides on both walls, then installing the last plastic strip will become a real challenge. When securing, great care will be required, since the starting strip must not be damaged.

Then a small strip of plastic is measured and cut from its sheet. It is possible that the strip will be measured in length and width. For cutting plastic, it is best to use a regular construction knife, he copes with this manipulation perfectly.

One side of the plastic strip is inserted into the starting profile. On the other side you need to put on a plastic corner profile and secure it to the frame with self-tapping screws. The other side of the plastic box is sheathed in exactly the same way, with one exception. The last strip of plastic must be installed with the starting profile on. It is better not to secure this strip with self-tapping screws. It is much more convenient to install using silicone. She will hold on tight. If dismantling is necessary, the silicone can simply be cut off with a knife.

After installing the plastic, it’s time for the inspection holes. They need to be cut in predetermined places. Hatches are installed in the holes to provide access to meters and taps. Inspection hatches You shouldn't screw it either. It is much more practical to glue hatches onto a plastic box using good sealant. At this point the work can be considered completed.

Video: Pipe box in 30 minutes!

If you want to get a beautiful bathroom as a result of renovation, then you will need to try not only with the choice of ceramic tiles and plumbing fixtures, but also with the preparation of the room itself. For example, it is worth hiding not very beautiful pipes that are unlikely to fit into the design of the room. You will learn how to make a pipe box in the bathroom and what it can be made from in this article.

Is it possible to build a box?

The design of the box is usually quite rigid and does not imply easy dismantling for pipe repair. Therefore, before erecting the structure, it is necessary to check their condition. If you have old communications, it is advisable to replace them with plastic. When replacing, try not to use soldering, mount whole pieces of pipes.

The fewer connections there are in the communications, the less likely it is that you will have to break the box to fix the leak. It may never be necessary.

How to make a box for pipes in the bathroom: 2 options

You can cover the pipes with a box built directly around them, or cover the entire wall with communications, including the pipes. The first option creates a small threshold if the pipes run parallel to the floor or a column if they are vertical. In addition, you can save on the material from which the box will be mounted. The second option reduces the space of the room, but this can be partially corrected by making a niche for storage and niche shelves closed with doors.

Materials for creating a box

Bathroom - special room your home, so the materials for installing the box should be:

• moisture resistant;
• environmentally friendly.

To install the box, you will need these materials to be not too thick or heavy. Considering the parameters, you can use the following materials:

• moisture-resistant plywood;
• plastic.

It is more convenient and reliable to use plasterboard or plastic to create the box.

Advantages of using plasterboard for a bathroom box

It is worth making a box from moisture-resistant plasterboard because:

• good resistance to moisture. It has been used in similar spaces for many years;
• it is easy to cut;
• All construction stores they sell moisture-resistant plasterboard - there will be no difficulties in purchasing it;
• On top of the drywall you can lay tiles, paint or apply any other decorative coating.

Advantages of using plastic for a bathroom box

Plastic panels are also a good option for mounting the box:

• quick installation that does not require a lot of tools;
• excellent moisture resistance if you coat the joints with sealant during installation;
• you immediately get an attractive surface that is easy to use;
• the material is not afraid of temperature changes;
• simple and quick repair or dismantling.

Drywall pipe box in the bathroom

First, let's look at all the nuances of creating a box for pipes in the bathroom, mounted from plasterboard. If you have ever twisted drywall with your own hands, then take a quick look at the most important tips in this section and its last part about the collapsible design. You already know everything else.

To install a plasterboard box, you will need the following tools:

• metal scissors;
• screwdriver or screwdriver;
• screws and possibly dowels;
• roulette;
• pencil;
• level.

You probably already have most, if not all, of what you need.

Instructions for building a plasterboard box

1. You should measure the walls near which the pipes are located. Compose detailed plan placement of connections (places of possible leaks) for the future. Doors should be located opposite the meters and valves. If you want the box to look uniform, then make removable parts of the structure instead of doors.
2. Make markings for the future structure on the walls, floor and ceiling (for vertical structures).

The distance between the pipes and the walls of the box is at least 2.5-3 cm!

1. Using a galvanized profile, make a frame for the box according to the markings. To do this, you will need self-tapping screws and a screwdriver if the walls are made of plasterboard. You can get by with a screwdriver, but the work will take more time. If the walls are brick or concrete, then use dowels and screws.

If you are installing a box for vertical pipes, then first make guides along the walls. Then the front edge is attached using hangers or a curved edge, and only after that the galvanized profile is mounted on the ceiling and along the floor.

In the case of installing a vertical box, non-standard designs with several edges (corners) are quite possible.

If the vertical box is more than 1.5 meters, then when installing the frame between the guides it is necessary to make jumpers from the profile. Maximum distance between jumpers - 1 meter.

1. Prepare the drywall sheets for installation so that there are as few joints as possible.
2. Use self-tapping screws to secure the sheets of drywall into place. Don't forget to make a hole for further access to communications.
3. Putty the corner or corners of the structure and the joints between the sheets.
4. Decorate the box in the same way as the rest of the walls in the room, including installing the baseboard.
5. Insert the door to access communications.

At the beginning of the article, we said that even a box the entire wall can be made useful design. Watch how you can make a niche in the video:

Collapsible plasterboard box design

It is possible to install a collapsible plasterboard structure when building a pipe box in the bathroom. To do this, secure the sheets along the very edge and do not putty them. Finishing work they are not made at the edges - they are closed using corners. This way, when you need to disassemble the structure, you simply remove the corners and unscrew all the screws. Assemble such a box after repair work the pipes will not be difficult - it will take 20 minutes at most.

Plastic pipe box in the bathroom

The easiest option for a bathroom box is to mount it from plastic panels. Even if you are everywhere ceramic tile, this material will fit perfectly into the interior. The main thing is to choose desired color and do not overdo it with the drawing. The best option will become monochromatic plastic panels.

Tools for installing plastic panels

For installation you will need:

• a drill or screwdriver with a tile drill, if you have finished finishing with ceramic tiles;
• self-tapping screws or dowels for the box;
• plastic cutter, grinder or jigsaw;
• roulette;
• level;
• silicone

As you can see, there are much fewer tools than in the case of installing drywall. And if you add the tools for finishing the tiles and the time it takes to lay them, it becomes clear that a box made of plastic panels is an ideal option!

Instructions for building a box from plastic panels

Let's take a step-by-step look at how to make a box from plastic panels:

1. Make markings for the box. How to do this, see above, in the instructions for plasterboard construction.
2. Install the profile box. It can be made the same as for drywall, or you can dispense with the front edge.
3. Prepare plastic panels according to the dimensions of the structure.
4. Using silicone, glue the panels to the profile.
5. Glue the corner between the panels using silicone.

Options for utility access doors

It is imperative to leave yourself the opportunity to access meters, pipe connections and taps. To do this, you will need a door or several opposite these elements. You can buy it (hatch, blinds, built-in door) or make it. If you make the door yourself, make it from the same material as the rest of the structure. It should be decorated in the same way as the box itself. To make it convenient to use, glue or screw a small furniture handle (these are usually installed on kitchen sets). To prevent the door from opening spontaneously, it must be equipped with magnets. You can make an invisible door. How it is mounted is shown in the video below.