Apartment renovation from scratch in a new building in Anikeevka. Where to start renovations in a new building. Latest finishing work

When the first euphoria from the appearance of a new home wears off, it’s time for serious reflection. It’s good if you already have experience in repairs or someone close to you is ready to advise you step by step. But, as a rule, every new resident, faced with this task, is left alone with it. Before you begin renovations in a new building, you must decide for yourself about the team.

You can do repairs in a new building with your own hands, hiring the right craftsman at the right time.
A more advanced option is to work with a designer and foreman.

It can be done well in both cases. True, the chances here are not equal. You can save money if you take on more of it yourself. True, here it is worth sensibly assessing all the pros and cons. It will take you a lot of time to figure out all the details, search the necessary specialists, the choice of building materials, and, of course, your nerves will also go to waste.

Advantages of renovating an apartment from scratch in a new building

Obvious advantages are the absence of the need to dismantle previous communications and remove wallpaper, ceilings, floors, doors, etc. In front of you, one might say, is a blank sheet of paper, and you have already saved on dismantling and garbage disposal. Moreover, in front of you fresh apartment, in which you can make literally any dream come true.

Where to start renovations in a new building?

First of all, you need to independently, or better yet, with a foreman, assess the condition of the apartment after commissioning: find out the material of the walls, determine exactly which of them are load-bearing, and which you can demolish if you wish. Request a utility plan to find out where the pipes are located hot water how electricity is organized. This is important, because during repairs you can damage the base already made by the developer. You can also save on warm floors, if the hot water pipes are located, for example, on the floor in the bathroom.

Before you begin renovating an apartment in a new building, you also need to evaluate the walls and floor, paying attention to obvious defects: uneven floor slabs, holes, cracks, voids in the blocks. Examine the windows carefully, check whether all modes of the opening mechanisms work. Also allow for the fact that new house gives "shrinkage". There is a risk that repairs made quickly will have to be repeated again.

The procedure for renovating an apartment in a new building

Renovating an apartment from scratch in a new building means, first of all, a clear idea of what zones you need. If you are satisfied with the layout, location and size of the rooms, the task becomes easier. If you decide to connect the kitchen with one of the rooms, add a balcony, change the layout of the hall, then you will need redevelopment. There are a number important rules, but you should not be guided solely by information from the Internet; be sure to clarify all questions on the spot with the relevant authorities. Of course you can't demolish load-bearing walls. This can damage the structure of the home and lead to serious problems. When connecting a balcony, you cannot move the battery, even to an insulated balcony wall - you need to find a new place for it in the apartment area. In a word, redevelopment, its coordination and the construction of new partitions is, perhaps, the first thing worth doing during renovation in a new building from scratch.

Attention, air conditioning!

Many would agree that today in summer time Air conditioning is no longer a luxury, but simply a necessity. Even if you are not ready to buy it during repairs, since expenses will be incurred on all fronts, it is still worth addressing this issue. There are two reasons. Legislation regarding this cooling technology changes frequently. Even if you notice external blocks near your neighbor or on opposite facades of houses, this does not mean that it is allowed to be hung in your home. Please clarify this issue first with the building association or the housing office, or better yet, immediately with the administration of your district with the chief architect.

Illegally hung air conditioners are subject to mandatory dismantling. You will simply lose money.
ATTENTION!

At the stage of rough work it is worth laying special copper pipes and other communications for him. You will definitely have to ditch the walls and then plaster them. If you paint or wallpaper first, you will have to deform in this place redecorating and it is ugly to run pipes. It is also worth paying attention to the fact that you, for example, assume that the air conditioner will be in one specific place on the wall, and its external unit right behind him on the street. But it doesn’t always work out that way, especially if you have top floor. Otherwise, climbers will be needed for installation.

Do-it-yourself renovation in a new building

As has already become clear, it is necessary to start with the preparation of the project and rough work: the construction of new walls, the work of a plumber, an electrician. If everything is more or less clear with the sewer system, you know where you have washing machine, bath, washbasin - then the electrics require more subtleties. Especially we're talking about about the kitchen. Don’t assume that, for example, where you plan to put a dishwasher, there will be an outlet right behind it. It is not recommended to do this. There is a high probability that you will have to make the width of the tabletop larger (non-standard) so that the plug of this technique does not bend, and indeed fits into the socket.

If you are doing renovations yourself, then it is better to go to any furniture company that produces custom kitchens at the very beginning, provide them with your measurements and prepare a design project together. Almost all establishments provide this service free of charge. This is necessary to get a kitchen estimate. You will immediately learn about all possible facade materials, countertops, baseboards and a host of other details. But the main thing is that you will understand what kind of kitchen awaits you, where what equipment will be located. In this regard, you will know exactly where you need to make sockets and where to bring out the wires for lighting, for example.

In general, the goal is to complete the electrical and plumbing connections before installing the ceilings and creating screeds. According to the technology, it is necessary to wait 28 days until the screed reaches its final strength. Next, you can start laying tiles and other floor coverings. At the same time, workers can make walls: prepare them for painting, decorative plaster or wallpapering. If you have chosen plasterboard ceilings or plaster them, then these dusty works must also be dealt with in this phase of repair. Stretch ceilings can be done at any time - best after dirty work.

After all of the above, we can say that the answer to the question: “Where to start repairing a new building with your own hands?” - has already. Pleasant moments of interior design and decor are ahead.

Each of us tries to arrange a new apartment to our own taste. Therefore, before moving into a newly purchased apartment, we have to endure the difficult test of renovation. As a rule, the matter is not limited to wallpapering, so this process often drags on for several months. After reading this article, you will learn how to make one from scratch in a new building.

A few words about shrinkage

The most important feature of any new house is that in the first few years of operation it will shrink slightly. Therefore, when using incorrectly selected building materials, cracks may appear on the ceiling and walls of the apartment.

To ensure that your efforts are not in vain, you need to follow the first and basic rule of renovation in a newly completed house. The initial renovation of an apartment from scratch in a new building should be the cheapest. Bring housing to perfect condition It is recommended not earlier than one and a half years after construction. During this time, you will have time not only to carefully consider all the details of the future interior, but also to save up a sufficient amount of money. In addition, it is possible that in a year and a half you will identify certain nuances that will force you to completely or partially abandon your original plans.

In what form do developers rent out housing?

Depending on how ready the apartments are to move in, they can be divided into three categories:

Without finishing (for an open plan). Such housing is an uncomfortable room with bare walls. By purchasing similar option, you should be prepared for the fact that you will have to bring it to mind yourself. Such apartments have an entrance door and windows, as well as electrical, gas and water communications.
Rough repairs. Apartments from scratch in a new building belonging to this category are prepared for decorative finishing. As a rule, they have heating appliances and inexpensive plumbing. Such housing is rented with already plastered walls and floor screed.
Finishing, which includes inexpensive decorative finishing. In such apartments, budget wallpaper has already been hung and linoleum has been laid. All that remains for the happy new residents is to install plumbing, lighting and bring in furniture.

Before buying a home, you need to inquire in advance about the condition in which it will be rented. Consider all the proposed options and choose the one that best suits your requirements. This is the only way you can make renovating an apartment from scratch in a new building less expensive.

Who will do the repair work?

Ideally, to speed up the process, it should be entrusted to professionals. They will do everything at the proper level and in the shortest possible time. In this case, the happy owners can only move into a new, fully finished home.

However, in practice, people often spend all their savings on purchasing an apartment. Therefore, they have no money left to pay for the services of professional craftsmen. This is especially true for those who took out a mortgage. IN in this case you will have to independently renovate the apartment from scratch in a new building. Moscow is very Big city, so its residents should not have problems finding and purchasing the necessary building materials.

When is the best time to start renovations?

To successfully complete this important and responsible activity, you need to carefully plan the timing of it. It should be understood that each season is characterized by its own advantages and disadvantages. Thus, in winter there is a decline in activity construction market, so at this time you can significantly save on materials. But before you start renovating an apartment from scratch in a new building, you need to carefully weigh the pros and cons. After all, it’s unlikely that your neighbors will be delighted when you start turning off the risers to replace batteries and plumbing.

In the spring, there is a gradual activation of the construction services market. Crews are starting to schedule work, but prices are still fairly low. It is at this time that it is best to begin renovation work in order to have time to celebrate housewarming by the summer.

In summer and autumn, prices for building materials remain quite high level. In addition, in the first case, in order to renovate apartments from scratch in a new building, the price of which during this period will reach sky-high heights, you will have to refuse summer holiday. Well, in the fall there is no time to do such work, because at this time it is necessary to supervise the studies of schoolchildren and clear away the accumulated office problems.

Main stages

Renovating an apartment from scratch in a new building is carried out in the same way as a major renovation. In most cases, the main work falls on the shoulders of the owners themselves. The approximate list of work required when purchasing a home with an open plan includes the following steps:

installation of walls or interior partitions;
cutting grooves and holes for electrical wiring and pipes;
wiring and installation of all engineering and technical communications;
and gender;
plastering walls;
installation of interior doors;
finishing of window slopes;
performing final decorative finishing;
final work, including switches, connecting lighting fixtures.

Benefits of working with a contractor

Renovating an apartment from scratch in a new building is quite a troublesome and time-consuming task. Therefore, it is better to entrust it to experienced workers. The contractor’s responsibilities include keeping records of the building materials used, drawing up a clear work schedule and forming a professional team. If necessary, he can also organize delivery of the necessary construction materials to the site.

Features of cooperation with hired organizations

Many unscrupulous contractors seek to deceive customers. To avoid such problems, you need to have a record sheet with you. finishing materials, used for work. This will help you completely control their consumption.

It is important to agree in advance on the transportation of building materials using an elevator. Massive renovations in new buildings often lead to the formation of entire queues of people wishing to take advantage of this benefit of civilization.

In addition, before signing a contract, it is recommended to clarify in advance the time for performing work that is associated with increased noise. Thanks to this, you will be able to adjust the timing of repair operations and minimize possible economic risks. If you are planning to install a system in your home fire safety, then it is advisable to discuss this point with the contractor in advance.

Apartment renovation from scratch in a new building: cost

Before starting work, you need to carry out comparative analysis market prices for building materials. In addition, due to the complexity of the repair, you need to figure out whether it would be easier to entrust it to professionals. Thus, the average cost of a comprehensive renovation in a new building located in a region with well-developed infrastructure varies from 2,400 to 6,000 rubles per square meter. Please understand that these are only approximate figures and depend on many factors.

The cheapest is economy class repairs. It includes meters with automatic machines, switches, sockets and ceiling lamps. The floor is covered with linoleum, and the putty walls are covered with wallpaper.

The so-called basic repairs will cost a little more. In this case, the list of works will be supplemented by leveling the floor, covering walls, laying tiles, and insulating the front door and windows.

When signing a contract to perform an expensive complete renovation, you can expect to receive a home that is ready to move out of a bare box.

For those who do not have huge sums of money, but still plan to renovate an apartment from scratch in a new building, we can recommend doing a budget one. In this case, the linoleum you have chosen can be laid not on the screed itself, but on a layer cork backing. This way you will get a warmer floor without spending huge sums on it. The walls can be painted or covered with inexpensive paper wallpaper. The bathroom can be laid out on a budget ceramic tiles domestic production.

Buying a fresh apartment in a newly built multi-storey building, you get literally bare walls and communications in a budget design. It is clear that you will have to bring it into a habitable state yourself or with the help of hired personnel. Regardless of whether you do major renovation in a new building with your own hands or contact specialists, you need to have a good idea of the sequence of work so as not to spend extra money on alterations. Hence our goal - to tell you how to renovate a new home step by step from scratch to finishing.

Where to start repair work

Not at all from plaster, as a person ignorant of construction will immediately say. High-quality repair turnkey apartments – the procedure is not easy, requiring integrated approach and planning. Otherwise, its final cost will be exorbitant. You need to start with an audit: find out what has already been done in the apartment and does not require improvement, and determine what elements need to be changed (for example, cheap windows or unnecessary interior partitions). Then create a plan that reflects all stages of the process.

The original condition of the home in a new building

We present universal step-by-step instructions that you should follow for successful renovations in a new building:

Project development, selection of materials and budgeting.
Preparing the facility for repair work. Calling measurers for doors and windows, laying utility networks by floor.
Leveling ceilings, priming and painting. Construction of new partitions (if necessary).
Waterproofing the ceiling in the bathroom, applying plaster to the walls and preparing the floors for the installation of a rough screed.
Installation of doors and windows, glazing of balconies and loggias. Replacement heating devices, pouring screed along the beacons.
Laying utility networks - pipes, electrical wiring and freon routes for the air conditioner in the furrows of the plaster. Installation of toilet installation.
Priming and sanding walls, finishing balconies. Installation of a bathtub and various plumbing elements hidden behind the casing. Tiling the bathroom.
Cleaning the surface of the screed and adjusting it using self-leveling mixtures.
Applying primer to walls and wallpapering. Final finishing of the ceiling.
Laying flooring, installation internal doors, built-in furniture and baseboards.
Installation of sockets, switches and finishing plumbing – sinks, toilets and so on.

Advice. Decide how many items from the list you are ready to implement on your own, and what work is best entrusted to builders or communications installers. Then find out the price of these services and include them in the estimate.

Why it is important to follow exactly this procedure when arranging a new apartment, a famous master will tell you in his video:

Preparatory stage

This includes the first 2 points of the presented list. The project and estimate are where you should start renovating a new building in order to clearly understand your costs and deadlines for completing finishing work. Design in your case is drawing sketches and thinking through cladding options in order to optimal choice materials.

Advice. In the first years after construction, the building shrinks, so for the initial arrangement of housing it is better to get by inexpensive materials. After a few years, it won’t be a shame to replace them with better ones.

It all starts with garbage collection

The project should include the type of cladding, its quantity and even dimensions tiles and wallpaper, so that less waste is left when applying the sticker. Visit several stores and select suitable finishes along with shaped and mounting elements. If necessary, redesign the rooms and make the doorways wider. Then start preparatory work in this sequence:

1. Provide lighting in all rooms, power supply for tools and water supply.
2. Bring cleaning tools and bags for construction waste, buy protective equipment (respirators, gloves) and protective clothing.
3. Remove unnecessary partitions, cheap radiators and windows, widen doorways.
4. Remove dust and construction debris. In a one-room or two-room apartment you can handle this task yourself, and for homes large area It is worth engaging a specialized team for the removal of waste construction materials.

Expanding the opening is not an easy task, it is necessary to install reinforcement

Note. If the developer has laid heating lines made of polypropylene, they should also be dismantled. In data polymer pipes there is a bad feature of leaking at joints 1-3 years after poor-quality installation (and you cannot check it). Therefore, it is not recommended to lay them in a monolithic screed.

Not the best option wiring for embedding

Measurers from companies that sell windows and doors should be invited at the beginning of the renovation, because they require 1-2 weeks for production. If you want to order furniture for the kitchen, then the craftsmen should also be called at the preparation stage so that they have time to communicate their requirements for plumbing and electrical connections to certain points.

After dismantling the economical heating option in the form of PPR pipes in the floor, you need to lay new lines. To carry out this work, it would be correct to buy high-quality pipes made of metal-plastic or polyethylene and invite specialists who know all the nuances of such installation. You will get more information on this topic from the following video:

Ceiling finishing

This procedure should begin with sealing the joints between floor slabs, which are traditionally not laid very evenly. The technology for aligning seams is described in detail in our resource. The next step is applying primer deep penetration for the purpose of surface preparation and dust removal.

Important point. If you are rebuilding room partitions, for example, making a studio apartment, then their construction should precede the cladding of the ceilings.

It is convenient to do priming with a roller on a long handle

There are several ways to quickly finish a floor by carrying minimum costs:

coloring water-based compositions;
plastic covering;
wallpapering or decorative panels made of polystyrene foam.

The first two options are good for corridors, balconies and kitchens, but in the living room and bedroom they look too ordinary. A common method is finishing ceilings in a new building. foam panels, easily done with your own hands. Eat simple technology: tiles are glued to the prepared surface along diagonal lines drawn between opposite corners. The result is quite decent, as shown in the photo.

Advice. The final covering of the ceilings is carried out after plastering the walls, so these processes will have to be alternated.

At the same stage, waterproofing of the ceiling in the bathroom is done. The procedure is simple: fill in the uneven areas. cement mortar, carefully prime and apply the waterproofing polymer mixture with a wide brush. It is necessary to apply 2 layers with a break for drying, and protective covering should go onto the walls, as shown in the photo.

How to repair walls with plaster

We are considering this method interior decoration for two reasons:

High-rise buildings take several years to shrink, causing cracks to form in different places. There is a high probability that expensive repairs will be ruined.
Due to cheap plumbing materials and poor-quality installation from the developer, breakthroughs and flooding of apartments are possible at first. The result is similar.

To plaster the walls you will need a ready-made mortar based on cement or gypsum, reinforcing mesh - serpyanka and deep-penetrating primer. IN panel house You must first seal the rusts between the slabs (especially in the corners) with cement mortar. Then the sequence of work is as follows:

1. Remove as much dust as possible from the surfaces and apply primer in 2 steps. On smooth concrete walls make notches with a chisel for better adhesion to the solution.
2. Using a building level, install beacons from metal profiles in increments of 1.5 m, fixing them with gypsum mortar.
3. Prepare plaster mixture and apply the first layer with a trowel, leveling it with a grater. Then press the mesh into the solution and, after setting, apply a second layer, stretching the mixture as a rule to the level of the beacons.

When the surface hardens a little, you should remove the beacons and seal the remaining grooves. Last operation– grouting performed to final level the wall, as shown in the video:

While the plaster in the rooms is hardening, they must be installed entrance doors and all windows are glazed. The next stage according to the plan is the preparation of floors and...

Filling the screed

The technology for installing a concrete floor is similar to plastering, only it is performed with a cement-sand mortar (it is better to purchase ready mixture). The set of tools is similar: a level bar, beacons, a mixer for a drill and a trowel. The correct screed in a new building is done like this:

Carefully coat the cleaned and leveled surface with primer.
Take a little dry mixture, add gypsum powder there for quick hardening and make a small batch of the solution. Use it to place beacons made of galvanized profiles at intervals of 1-1.5 m.
Prepare the worker cement-sand mortar and lay it on the floor, stretching it with the rule. Special attention pay attention to the corners of the room.
After 12-14 hours, when the screed has set, use the same rule to clean off the excess mixture, then remove the beacons and seal the marks on the surface.

Metal beacons for pouring

Note. The height of the screed in the bathroom should be 3-5 cm lower than in the rest of the apartment. It is recommended to reinforce a thick layer of mortar (over 80 mm) with masonry mesh.

Subsequently, when the concrete floors have completely hardened, they can be further leveled with a special mixture and prepared for laying laminate or other material. This operation is performed after finishing the ceilings. The screed device is clearly demonstrated in the video:

Installation of utility networks

Work on laying communications is divided into 2 stages - rough and finishing. The first is done after plastering and pouring the screed, the second - after finishing. Rough installation includes the following operations:

Advice. When extending cables, do not forget about low-current networks - twisted pair for the Internet and cable television, alarms and video surveillance. These types of wiring should also be hidden in the walls and then the corresponding connectors should be brought out at the right points.

If the apartment is planned to be installed household split system, then there is no better time to lay freon pipes. Together with your air conditioner technician, determine the mounting points for the external and indoor unit, and then lay highways between them required diameter, hiding them in the grooves of the walls, as done in the photo.

The final installation of utility networks is the installation of plumbing fixtures and room sockets with switches. His turn is one of the last on the list: work is carried out after finishing (pasting wallpaper and tiles, covering ceilings).

Conclusion

If you look at the repair plan for a new building, it becomes clear that each type of work - plastering, screeding, panel finishing - is not carried out entirely, but in parts. For example, it is not advisable to lay laminate on floors until the cladding of ceilings and walls is completed, otherwise the material may be damaged. That is why it is important to follow the sequence of work, then you won’t have to redo anything.

Have you finally received the keys to your dream apartment in a new building? You open the treasured door, and there - empty walls, gray screed on the floor, lack of doors and lighting. On the one hand, this is a huge space for us to maneuver and the opportunity to organize our own space from scratch, on the other hand, there is fear of costs, worries, loss of time, and the question - where to start? Such thoughts arise in many owners of new buildings; the dream has come true - you are the owner of your brand new own apartment. Now we need to decide where to start repairs in a new building step by step in order to do everything correctly and avoid mistakes. We will talk about this in this article.

Renovation of a new building in stages - how to plan

Work on interior decoration and interior design should begin with careful consideration of each step. In this case, we recommend using common sense, patience, and detailed plan actions that will help you manage your work well, save time and money.

Detailed interior design should be developed at the raw room stage. It's not always as simple as it may seem. On the one hand, we know what we expect from our apartment, but we have no idea where to start arranging it. Experts offer the following work plan on how to renovate an apartment step by step in a new building.

Step-by-step repairs in a new building without finishing

Planning the layout of the walls. At this stage, you can remove unnecessary walls or build new walls or partitions. Not all partitions can interfere; you cannot demolish the load-bearing walls of the building, all types of pipes or ventilation.
Electrics– you need to determine whether there is a sufficient number of electrical outlets and are they all in in the right places:
- are planning additional lighting or change its current location;
- adding light switches on the stairs - very convenient solution in houses where there is a large hallway;
- additional sockets;
- we are planning various sockets in the kitchen, including a socket for dishwasher, hoods, under-cabinet lighting, socket for induction cooker and ovens;
- in the living room, we plan connection points to the cables and places for laying the antenna cable, wired Internet, cable from the TV, while some of the cables can be hidden in the wall, and some in the baseboards.
- All this work must be completed before the final painting of the walls in the bathroom and kitchen before laying the tiles.
Plumbing– check the hydraulic connections, whether the radiators are located in the places where you planned – if not, there is still time to rearrange them. Plumbing work can be done before, after or simultaneously with electrical work.
- installation of pipes for a dishwasher and sink in the kitchen (disguising pipes, moving connections to the right, left);
- installation of pipes in the bathroom, depending on whether we want to install a bathtub or a shower, for a shower a fairly popular solution is a shower drain or a drain line;
- installation of installation for toilet and bidet (connection of water supply and sewerage).
Laying floor tiles . It should be remembered that the tiles must be laid before we begin laying parquet or laminate flooring. We place the tiles at the desired height, adjust the height of the tiles to the height of the wooden floor or laminate (if batten has a height of 14 mm, the tile is placed at a height of 15 mm, under parquet board, having a thickness of 14 mm, an adhesive layer having a thickness of 1 mm is applied).
Preparation for painting and painting of walls and ceilings. As a rule, developer walls and ceilings leave much to be desired and require repairs (they have visible scratches, air bubbles, holes, etc.). Depending on the condition of the walls, following works:
- plaster;
- sanding walls and ceilings;
- primer (reinforcement of the substrate);
- one-time painting of walls.
Preparing the floor surface(grinding concrete, and if it is boards or parquet, laying film, insulation, cork, etc.).
Parquet work / flooring installation– the wooden floor should rest for 2 weeks after installation; if we chose laminate, we can use it immediately after installation.
If necessary, final painting of walls, wallpapering, etc. Installation of sockets, switches.
When it comes to interior design, at this stage it is better to start with the kitchen and bathroom. In the bedroom, you can sleep on a mattress located on the floor, in the living room, you can sit on poufs, but in order to quickly move into your apartment you will need a kitchen and a bathroom.
Installation of sanitary equipment and sanitary ware, taps and mixers in the bathroom.
Carpentry - planning kitchen furniture, bathroom installation, cabinet planning, measuring and ordering interior doors.
Kitchen design - installation of furniture, connection of a refrigerator, dishwasher, oven, hob, sink and faucet.
Installation of internal doors, skirting boards and electrical equipment.
Selection of curtains, blinds for windows.

Contract with the contractor

It is advisable to conclude an agreement with the contractor in writing. Such a document in the event of a dispute will become the basis for compensation. It is worth discussing:

The parties, the subject of the contract - the scope of work and the dates for their commencement and completion.
Remuneration for performers, terms and methods of payment. You can pay according to the estimate of the planned work, or at a fixed rate - based on the agreed amount of the work estimate. The second option is more profitable for you - the contractor cannot demand an increase wages.
Statement from the contractor who undertakes to perform the work in accordance with the rules and construction standards.
Penalties if the contract is not fulfilled or is not performed improperly by one of the parties, as well as a condition on the possibility of demanding compensation for losses.
Signatures of the parties.

The contract should indicate the amount of payment and deposit for the contractor. Enter a caveat that if he fails to comply with the terms of the contract, you may require him to pay double the deposit.

In the case of turnkey interior finishing from the developer, much depends on the contract. Some developers provide flooring (laminate), interior doors, wall coverings (tiles) and plumbing, some even offer interior design.

Advantages of turnkey finishing from the developer:

you save time while shopping;
there is no need to search for and control performers.

Disadvantages of turnkey finishing:

rarely does the customer agree with the quality of finishing materials and work performed;
limited choice of performers;
disagreements in design solutions and choice of materials.

When purchasing an apartment in a new building, many people tend to choose housing without finishing. This desire is due to the lower cost of real estate and the excellent opportunity to carry out the necessary repairs, taking into account taste preferences and the available budget.

Finishing and renovating an apartment in a new building from scratch has a number of nuances that must be taken into account in order for the result to satisfy the owners.

What types of work can be done in a new building?

The main aspect that the owner of a living space in a new building should know is that the structure will undergo a shrinkage process over time, so cracks may form on the surfaces. Walls, ceilings and even floors will begin to crack in the early years. Experts recommend not using expensive materials or using high-quality types that are not susceptible to cracks.

IN new apartment originally It is necessary to perform the most noisy and dirty work:

installation of plumbing pipes;
electric installation work;
floor screed;
leveling wall surfaces;
installation suspended ceilings and installation of heated floors.

These works are carried out immediately after receiving the keys. Almost no one lives in the new building, so repairs can be carried out around the clock without disturbing neighbors and without fear of administrative liability.

Apartment layout

Proper organization of space in an apartment makes it possible to use the area more efficiently. Installation of all kinds of partitions and other elements, as well as demolition of walls or creation of additional ones in them doorways is mandatory with regulatory and specialized authorities.

Today, functional studio apartments are very popular; many owners also combine a room with a loggia. Such rooms look stylish and spacious. When combining a living space with a balcony, a set of insulation measures should be carried out.

Only after receiving official permission can you begin to build or destroy walls and other elements.

Preliminary work

At the initial stage, you should clearly formulate the basic requirements for the premises, decide on the layout, the number of rooms and the functions assigned to them, as well as the design and color scheme.

Should be considered:

financial opportunities;
repair period;
building shrinkage process;
indicator of suitability for occupancy and residence.

Scroll additional work depends on the degree of suitability of the apartment for occupancy. In monolithic buildings, apartments are sold with an open plan: there are no partitions or wiring of communication networks.

The preliminary stage includes rough work:, leveling surfaces, making partitions and other types, and creating an apartment if the owners do not want to hear noisy neighbors.

Renovating an apartment from scratch in a new building: step-by-step instructions

For proper implementation repair work in the apartment it is recommended to adhere to a certain step by step instructions. If any stage is not planned or there is no need to carry it out, then you can simply skip this list item and move on to the next one.

Step-by-step instruction:

Repairs must begin with the installation of a temporary toilet. After a while, it is replaced with a new product during the period when the sink, shower cabin and bathtub will be installed.
Carrying out work related to the installation or dismantling of partitions. To create, it is recommended to use foam blocks or ordinary bricks, which must subsequently be finished using.
Competent creation of grooves. Using a hammer drill equipped with a drill, the diameter of which must correspond to the width of the groove, grooves are made in the surfaces for the cable. After this stage, the drill must be replaced with a peak, with the help of which the recesses are connected.
Electrical wiring work. They are laid in all areas of the apartment where electricity will be needed, and then the wires are connected to the panel.
Organization and installation of communication systems: installation of high-quality plastic pipes in the bathroom and kitchen. To prevent the presence in the apartment of an unpleasant and unwanted odor from sewer systems, you must use special plugs. They are needed provided that the connection to the communication will be made subsequently.
Work on the water supply system: initially carried out cold water, and then hot into the bathroom and kitchen area.
The ventilation openings are equipped with special grilles.
Carrying out wall surfaces and subfloor grouting.
Repair of door and window slopes.
Priming of pipes, radiators and connection to the heating system.
Assembly frame structures for built-in niches, cabinets and priming work.
Door installation.
Creation in the bath and then screeds.
Finishing the walls, ceiling and flooring in the bathroom and installing the sink, shower, toilet and bathtub.
In the remaining rooms, work is being carried out and screeding is being carried out.
Installation and...
Puttying walls and slopes.
Painting batteries and pipes.
Installation of interior doors.
Installation of switches and sockets.
Decorative repair and Finishing work: wall surfaces, fastening skirting boards, etc.

Renovating an apartment in a new building from scratch requires certain knowledge, experience and skill, so it is recommended to turn to professionals. You should not trust the work to non-professionals in an attempt to save money. This can lead to even greater costs that may arise in the event of unsuccessful and poor-quality repairs.

You should pay attention to the services of time-tested companies, consult with friends and colleagues who have used a similar service.