Do you dream of becoming a famous tattoo artist, but don’t know where to start and where to get the necessary equipment, which, moreover, costs a lot of money? There is no need to be sad about this because there is enough affordable way How to make a tattoo machine with your own hands. This will be a rotary type device. To make it, you will need the following simple “spare parts”: a power supply with variable voltage, the thinnest guitar string, a motor from an old cassette recorder or player with a couple of wires, a gear from the same, a small bushing, an ordinary gel pen, a piece of plastic tube.
So, doing it yourself assumes, first of all, the presence of a body. Actually, this is what you will hold in your hand when getting a tattoo. Let's start by making it. To do this, take the handle, remove the rod from it (we don’t throw it away, it’s needed) and trim it from the back by about a third. You can use a knife to make a small hole (about 5mm) in the side of the pen nose to make it easier to pick up mascara. Use a small file to clean the edges of the hole so that small sawdust does not get into the wound.
The next step on how to make a tattoo machine is to make a guide needle. It is made from the shaft of the same pen. It also needs to be cut to body length and paint removed. Next, remove the spout from the rod, take a needle and use it to squeeze out the ball from the inside. This is necessary so that the string can move. If the nose is too narrow, it needs to be widened by grinding off the tip with a file: the string should not get stuck anywhere or cling to anything. After all the parts are ready, we insert the nose of the rod into its rightful place, and the rod itself into the handle. The body is ready.
Continuing the topic of how to make a tattoo machine, let’s make a needle from a guitar string. Its length should be calculated so that the tip with which the tattoo will be tattooed always sticks out of the pen in any position. When the string is pulled back, that is, inside the body, its “needle” should stick out 0.5-1 mm. In the “front position” 1.5-2 mm is enough. You will need to make a loop at the opposite end of the string. Therefore, in order not to make mistakes in the calculations, insert the string into the rod, which, in turn, place into the body of the handle. And so that the string is even, does not bend or curl, it can be pre-tensioned and well calcined over a fire.
At this stage, we leave everything as is and proceed to the next step. a typewriter? Next we need to attach the motor. To do this, take a piece of a pre-prepared plastic tube (it will serve as a motor holder) and cut it lengthwise into two parts. After this, we take each half in turn and cut off a longitudinal piece several centimeters long from it. Determine the length by eye, because this cut section, when bent, should cover the motor by about a third. Each trimmed part, carefully heated over the fire, is bent and rounded. We insert the motor into these rounded halves (its wiring should go out). A handle is inserted into the groove formed below the motor from the cut tube (the untouched part). All this beauty is tightly wrapped with electrical tape or tightened with clamps. Next, we put a gear on the motor pin, which will serve as a kind of crankshaft that moves the needle back and forth. It should fit very tightly and not scroll. Next, we take the bushing: a string loop will be put on it, which should also fit tightly enough. We fuse the bushing into the plastic gear, closer to the center, but so that when scrolling, the needle does not fully enter the handle in any case.
The final stage of getting the machine will be connecting the motor wiring to the power supply wiring. We try to connect it to an outlet. It should work.
This instruction will tell you how to make a tattoo machine at home. In order to get a tattoo, you don’t have to go to an expensive artist or buy special equipment.
With little effort, it is possible to make the necessary equipment yourself.
To work you will need to find the following parts at home:
- Electric motor.
A motor from a children's toy with a voltage of at least 12 volts is suitable. A motor with a lower voltage is not needed - it will be too weak for such a purpose. - Power unit.
Any unit with a voltage of at least 12 volts will do. - Gel pen or mechanical pencil (plastic or metal).
It will serve as the body of the device and also guide the needle inside the machine. - Brace.
With its help, the engine will be attached to the gel pen. The bracket can be made from metal, such as a regular tablespoon, by removing the part that is used for eating. Instead of a spoon, you can use a toothbrush, heat plastic handle lighter and bending it into the letter “G” (an example is shown in the figure). - Insulating tape.
- Needle.
An ordinary guitar string is used as a needle (it is better to buy a new string from a specialized store). Choose the thinnest string. - Button with 4 holes.
Assembling the device
Take the pen, disassemble it and remove the ink from the refill.
Rinse the pen thoroughly; no ink should remain there. Using a file, grind down the metal tip of the rod so that the string passes through it without effort. Cut the rod about halfway (this is necessary to reduce vibration of the string).
Preparing the engine: attach a button to the engine axle using superglue. Make sure that the glue has time to dry completely before assembling the device.
The connection between the motor axis and the button must be of high quality and not become loose over time. Do not fill the remaining holes of the button with glue - they will come in handy later.
If a plastic gear is attached to the axis of the motor, you can not glue the button, but use a hot needle to make a hole for the string in the gear.
This is done as follows: first of all, the L-shaped bracket and the handle are connected using electrical tape. Tape the bracket tightly to the handle with several layers of electrical tape so that the bend of the bracket and the top end of the handle are flush.
A motor from a toy with a button glued should be attached to the other part of the bracket in a similar manner.
Now you need to pull the string through the handle and cut it, leaving some margin. The end of the string is then bent a few millimeters and threaded through one of the button holes (or through a hole in a gear).
By rotating the motor axis, you will notice that the string moves up and down. The tip of the string protruding from the rod is cut so that when the motor rotates, the string protrudes from the tip by 3-4 mm. Sharpen the string with a knife sharpening stone.
Now the power supply is connected to the engine. For convenience, you can attach a switch to the machine. The device is ready to use!
Don't forget about safety and hygiene! Use a new string and a new tip every time! Before use, boil the string in water for at least 10 minutes.
These simple rules will help you avoid contracting diseases such as HIV or hepatitis.
HOW TO MAKE A TATTOO MACHINE
We make a tattoo machine with our own hands. The very concept of tattoos was formulated back in the 20s of the 20th century. Today, people ink anything on their body and pay a lot of money for it, but not many people know that the tattoo itself was born in the zones 100 years ago. And today we will look at a device that will allow you to make tattoos in a professional manner. To create such a device you only need a couple of little things - a gel pen, a guitar string, a motor from a DVD player drive or from a toy car and Charger from mobile phone.
We take the paste out of the gel pen and remove the tip of the paste, where the ball is. Next, take the needle and insert the needle from the back of the tip and press until the ball falls out. Then we take the paste and blow it into the washbasin until all the gel comes out of it. Now it's time to make the stake. To do this, take a guitar string and remove the spiral from it in advance. we need a piece of string with a length of 20 centimeters. Next you need to sharpen one end of the string and for this we prepare an electrolyte. Take a coffee glass and pour water into it, then you need to pour two teaspoons of table salt into the water and mix the solution.
We take any 9 volt 1 ampere power supply (you can use a transformer from a game console like SEGA or similar) and a nail. We connect the transformer to the socket and wind the plus from the transformer onto a string, and the minus onto a nail. Then we place the nail and the string in the water, but make sure that they do not touch each other. We do not immerse the string completely in water, but only 2 - 3 millimeters. Subsequently chemical reaction the metal strings will break down and become sharper. The reaction must be continued for 15 minutes, then the string must be washed and in the end we get the sharpest stake for a tattoo machine.
After all this, we take the head for the belt drive and insert it into the motor shaft (the head can be found in any cassette recorder, it is put on the motor shaft in the mechanism), you can also use a gear, like mine. We take an ordinary needle and go to gas stove. We heat the needle and make one hole on the head, which we previously inserted onto the motor axis.
The hole should be made 1-2 millimeters from the center. Take moment glue and attach the motor to the body of the gel pen. After the glue has dried, you need to seal the fastening area with silicone, and then wrap it with tape for durability. Then the sharpened end of the string needs to be passed through the hole where we used to have a ball, the string should be in the paste, and its second end should be bent in the form of a hook and stuck into the hole that we made with a needle on the head of the motor.
Now we assemble the handle, connect the mobile phone charger to the motor and everything is ready. Tattoos are made with black gel from the same gel pen. To prepare, take several gel pens, take out the paste and tip, take the vodka stopper and gently and slowly blow into the paste. Subsequently, the gel will end up in the plug. Then we turn on the machine and within 10 seconds immerse the sharpened tip into the plug with the gel. Then we take it out and make a tattoo, and so on until the end of the tattoo.
The device has been tried many times and with its help you can make tattoos no worse than on a factory tattoo machine created only for such purposes. Be careful, as tattooing is one of the ways of transmitting infection! Before each tattoo, you need to wash the tip of the device with alcohol.
In the army I learned how to assemble tattoo machines, as well as draw and make half-hearted tattoos. I’ll reveal the secrets of unprofessional cuisine: cattle love to stuff themselves with scorpions most of all. Now, not without my assistance, a huge number of demobilizers are wearing identical scorpions on their arms and backs. A soldier’s main friend is a tattoo “For the Air Force” or “For the Airborne Forces”, tattooed on the edge of the palm, so that when pouring vodka into the mouth, this inscription is shown to drinking buddies. Images of such living creatures as scorpions, tigers, and dragons are held in high esteem. You can also make a meaningless pattern (Celtic, tribal). Each drawing should, according to thieves’ “concepts,” mean something neutral, so they are interested in the meaning of the drawing in the first place. Even details such as the open/closed claws of a scorpion and the raised/lowered sting are important.
But the main thing in this matter is the device itself. Assembly homemade tattoo machine- it’s a simple matter.
To create the device we will need the following items:
Gel pen:
Motor (a motor from a tape recorder, cassette player, VCR, printer is suitable, and at worst a motor from a Soviet children's toy will do): 
Eraser: 
Guitar string (first or second): 
Electrical tape (or scotch tape): 
Phone charger or power supply for Dandy: 
Let's start by breaking off the eating part of the spoon and bending the other part at an angle of 90 degrees. 
Let's saw the handle together with the rod. Jagged edges adjust with sandpaper or a lighter. 
Let's cut out a similar shape from an eraser: 
Let's put it on the motor spit. 
Let's take the ball out of the pen, maybe even bite it out with pliers. 
Using the same nippers, we will bite off a string measuring four centimeters longer than the handle. The string now needs to be sharpened using sandpaper, a whetstone, or a matchstick. 
Let's imagine what could come of all this. 
Let's use electrical tape. The rod should rise above the upper plane of the eraser by a millimeter or two. When rotating, the eraser should not touch the handle. 
We bite off the charging connector and strip the two wires. 
We solder or simply twist the charging wires and motor contacts, and insulate them generously with electrical tape. 
The string, coming out of the back of the rod, bends at 90 degrees, passes through the eraser and bends at the bottom of it. The principle of operation is the reciprocating movement of the string produced by the rotational movement of the crankshaft. On the other hand, where the tip of the string is located, there are also its own rules: the tip should not protrude from the rod by more than 5 mm.
The unit is ready to cause serious bodily harm. 
Tattoos constantly give us confidence and bring us a lot of joy. But nothing stands still, and today we will look at... Yes, this is already possible.
How to make a tattoo at home: henna, machine
That is, it is imperative to prepare and approach this very responsibly. If you do this, you can definitely become a professional who will be very high level. So, it is quite possible to get a tattoo at home.
How to make a tattoo at home?
Let's look at where you can get a tattoo, and most importantly, how you can do it. Firstly, you can get the necessary services in the salon. There you will be provided with everything you need, what you want, and most importantly, how you want.
- There are masters there who are always ready to help and provide the necessary services. That is, the salon is the first option.
- The second option is at home, here it is already characterized by the fact that you can receive services at someone’s home. It's not always legal.
And there is an option when very often they start getting tattoos on themselves. That is, you can simply apply the necessary object to yourself. To do this, you just need a machine and the necessary ink. There is absolutely nothing complicated here. The only negative is the complexity. It is very difficult to get a tattoo on yourself. It's practically impossible.
Let's take a closer look at how to make a sketch, if there are rules or something else. First, you need to sketch the drawing. Naturally, first you need to select the drawing itself, then come up with its color, size and background.
How to prepare a sketch of a house and start building it This is how you can make sketches. It is best to draw the part of the body where the tattoo will be, then you need to draw a picture there. Next, we decorate it with the colors in which the tattoo will be used. It must be fully consistent in size and shape. Next, the sketch that you got needs to be done with the background you need and colors.
We take the sketch to the master, and he makes a tattoo. Often you can make a sketch in the salon itself. These services are provided there. You can also do how to make a tattoo at home with a needle sketches. The important thing is that you can turn to a friend for help, who will definitely help you and tell you what to do.
You can download a ready-made sketch from the Internet that you like. Finding a sketch will not be difficult. You can prepare it yourself and not rely on anyone in this matter. You can do, for example, . It is very comfortable. You will definitely be confident that you are doing everything correctly.
Where can you get tattoos at home??
Let's take a closer look at where it is fashionable to get a tattoo. There are actually a huge number of options. They need to be disassembled. It is very popular and fashionable to get a tattoo on the arm, wrist, neck, back and shoulders. Very often we get tattoos where it is very popular and do not think about how beautiful it is. Today, tattoos are often done in intimate places.
Where can you get tattoos at home? There are a lot, . This place has a huge pain point, so be prepared to endure it. Also this option they don’t really like it precisely because it is characterized by the fact that no one will see the tattoo. She will be only for you and yours young man. Signatures on the hand are mainly distinguished by tattoos. So few people can decide and go for it.
Thus, just choose a tattoo for yourself and decide on the location. Everything may also depend on what size the tattoo will be, what kind of pattern and design it will have. If you can choose a tattoo, it will look aesthetically pleasing and beautiful everywhere.
So just get ready to look really good. Be sure to prepare yourself so that you can choose a tattoo for yourself. Today, tattoos are becoming a very popular form of art, which constantly enters and changes our lives.
Making henna tattoos for a long time Today, the place where you can get a tattoo is becoming more and more interesting. We consider it necessary to consider how to make a henna tattoo at home. There are a huge number of them. Thus, you just need to consider all their options and choose the one you need.
Let's take a closer look at what options there are for applying tattoos in intimate places. Firstly, there are a lot how to make a tattoo at home video. They will help you choose the right tattoo, teach you how to draw a sketch, and most importantly, they won’t let you make a mistake. With the help of the video, you can even get a tattoo at home.
Video of tattoos made at home There will be a recipe on how to make a tattoo. You can find the video on the Internet. There are so many options for how to get a tattoo. Firstly, there is a theoretical part of how to get tattoos correctly. There are other videos about how to make a tattoo at home recipe and photographs. They show the result of what you will succeed and what it can lead to.
It is very important to choose the right tattoo and place for it, this way you will do everything correctly and you will not have any problems or disagreements. Videos and photographs will help you see what you will end up with. You will see what kind of drawing you have and what to do with it. The video will teach you how to make tattoos using henna, permanent tattoos using a machine, and so on.
Just watch the video and it will tell you everything you need to know about tattoos. Today tattoos are a constant part of our lives. They change and develop it. So you need to know all the options and types of tattoos. It is not difficult. We will consider them in our article. It is very important to know about all the tattoos and their styles. This way, you can simply choose the perfect option for yourself.
