Attention! Access codes are only suitable if the installers are too lazy and did not change the default password. This happens quite often :)
Intercoms Eltis
Initially, the default code is "1234", but any company, when installing an intercom, naturally changes it to its own, and it is almost impossible to recognize it. To enter the password entry mode, you must hold:
1) any number key for 7 seconds ("code" menu - menu for working on apartments, key programming)
2) The "v" button - hold the same amount (the "sys" menu - general parameters, prohibition / permission of codes - 1234 is quite often suitable for this menu, I used it 50 times.)
Explanation of menu operations:
1. Calling the system menu "sys".
1) Press the "in" button and hold for 7 seconds.
2) After the inscription "SYS" on the display, enter the system password (stupid lazy system people often do not bother to change the password, which is the default - 1234)
2.1) If the input is correct, the intercom will show the firmware of the form "6_7x", where x is the firmware number, then the "_FUNC" menu will be loaded.
Press from it:
"1" - "PAS" will appear, after the input field to change the old password to enter this menu (dial 4 digits and the intercom will return to "_FUNC"
"2" - menu "_ LOS" to enable / disable the general password for the entrance (buttons 1/0, respectively)
"3" - menu "_ dig" to change the general login password. Press 3, 4 or 5, "____C" will appear.
Depending on the pressed button, you can set a new password, respectively, 3, 4 or 5 digits. (type new password)
"4" - menu "_beep". This option enables/disables the signal to open an individual apartment code in this apartment (the handset rings when opened with a default code, buttons 1/0)
"5" - does not exist
"6" - menu "_FLOS" to enable / disable individual entry codes for apartments (to check, press "in" in normal mode, if "F" lights up, it means it is on)
"7" - does not exist
"8" - menu "_OREN" - to change the duration of the door opening (the number of signals will change, decrease / increase with the buttons from 1 to 9)
"9" - does not exist
"0" - exit
2. Serial number of the intercom.
Press "in" and hold for 20 seconds. 5 digits will appear and then reset.
3. Entering the engineering code (system menu "CODE" for work on apartments)
1) Dial any NUMBER and hold until the inscription "CODE", after which a field for entering a password will appear.
2) Enter the system password (default 1234 as in the first case)
3) If the input is correct, then the firmware will appear, then the "_FUNC" menu.
4) From this menu:
"1" - Set a new password to enter this menu (similar to the first case, see above)
"2" - Set a new common login password (4 digits).
"3" - work on apartment passwords:
"_FUNC"--> press "3"--> "F"--> enter the apartment number and press "to"-->"____C"--> enter a new code (but not 0000, because entering it , you will prohibit the use of the code for this apartment) --> dialing to the apartment will go --> ask to press the "open door" button TWO times --> the code is accepted, "_FUNC".
"4", "5" - menu "__ LF", but different options are hidden under different numbers.
"4" - disable / enable individual tubes in apartments. Dial the apartment number, then press "to". "*** #" will appear, where *** is the apartment number and # is the number 1 or 0 (on or off). Click the value you want.
"5" - key coding. Dial the apartment number and press the "in" button (see above). "***LF" will appear, where *** is the apartment number. Attach the key to the reader. If you have not coded the key before, the inscription "ADD" will appear, if you have coded it, the number of the apartment to which the key is recorded will appear. After encoding, you can open the door with this key after logging out.
"6" - menu "__ dF". Option to delete keys. Dial the apartment and press the "in" button. "_ dEL" will appear, press 1 - the number of keys that have been deleted will appear. (*del). Press 0 to exit to "_FUNC".
"7", "8", "9" - does not exist
Raimann intercoms
To enter the menu, do the following, press the "key" and drive 9 8 7 6 5 4, we hear
sound signal, then we drive 1 2 3 4 5 6, the letter P will appear, which means that we
intercom system.
So what can we do with the intercom? there are not many options here:
2 - standard intercom settings.
3 - Signaling.
4 - Door lock.
6 - intercom freeze
8 - Opens the door.
Intercom Cyfral
General code 1234.
Number of the first subscriber 1.
Signal duration Z 1.
Subscribers ON/OFF.
Intercom CYFRAL CCD-20
1. To change the number of the first subscriber, press the button "1", the indicator will display
"REG", then enter the number of the first subscriber and press the "K" button.
2. To enter the subscriber blocking mode, press the button "2", on the indicator
"bLC" will be displayed.
To block the subscriber, enter "O", "K", "Subscriber number". To unlock the subscriber, enter "1", "K", "Subscriber number".
In order to unblock all subscribers, you must enter "2", "K" in sequence. The indicator will display a confirmation request "POd", confirmation with the "K" button.
3. To change the code table, press the button "3", the indicator will display "tAb",
then enter the number of the new code table and press the "K" button.
CYFRAL CCD-20
4. To enter the lock programming mode, press the button "4", on the indicator
"L0C" will be displayed.
If key notification is not required, then you should simply attach the key to the receiving key device. This will turn on the beep and the key will be recorded. If the key is already stored in the call block memory, the display will show "ESt".
If notification by key is required, then you should dial the subscriber's number and then attach the key to the receiving key device. This will turn on the beep and the key will be recorded. If the key is already stored in the call block memory, the display will show "ESt".
If the call block memory is full, the display will show "REG".
Intercom CYFRAL CCD-2094
4.3 Programming mode
To enter the mode of changing settings and parameters, it is necessary to perform the following sequence of actions in the standby mode:
- press the "K" button, the indicator displays the message " ";
- press sequentially "0", "K";
- enter 4 digits of the access code into the programming mode.
After entering the 4th digit, the code is checked for a match. If the code matches, then the call block will switch to the settings change mode. In this case, the indicator will briefly display the version of the current software, followed by the message "Pr_".
In this mode, the functions shown in the table are available:
1 Changing the number of the first subscriber1
2 Caller blocking mode
3 Changing the current code table
4 Lock programming mode
5 Change access code to programming mode
6 Change of common code
7 Key notification on/off
8 Common code mode on/off
9 Apartment key erasing mode
5. To change the general access code, press the "5" button, the indicator will display
"CdO" and then " ". Next, enter a new code, the indicator will display " ". Click
any button except "C" and repeat the code entry. If all operations are performed correctly, then the indicator displays "ON" and a melodic sound signal sounds, the code has been changed.
6. To change the access code to the programming mode, press the button "6", on
indicator will show "CdP" and then " ". Next, enter a new code, on the indicator
" " will be displayed. Press any button except "C" and repeat the code entry. If all operations
made correctly, then the indicator displays "ON" and a melodic sound signal sounds, the code has been changed.
7. To enable / disable the sound signal in the TAP when opening the lock with a key
press the "7" button, the indicator will display "0t2",
In order to disable the sound signal, press the "0" button. In order to enable the sound signal, press the "1" button.
8. To enable / disable the opening of the lock with a common code, press the button "8", on
indicator will show "ECd,",
To enable the use of the shared code, press the "0" button. In order to disable the use of the shared code, press the "1" button.
9. To enter the apartment key erasing mode, press the "9" button, on the indicator
"ErS" will be displayed.
In order to erase the keys that are not recorded for a specific subscriber number, you must enter "0" and then press the "B" button.
In order to erase the keys recorded by a certain subscriber number, you must enter the apartment number, and then press the "B" button.
The above listed by me is not the author's material, and can only slip as a manual for those. maintenance, BUT NOT INSTRUCTIONS for hacking
P.S.
factory code 1234
Intercoms VIZIT
You can try dialing *#423 to open the door. (does not always fit)
Entering the service mode is quite simple:
# 999-beep 2 times- enter the master code, by default 1234, if approached-beep 1 time
if the code is incorrect, it will beep with a two-tone signal and the red LED will light up.
Decoding of operations (since there are few of them in the service mode, the decoding of the buttons is given here:
2-setting individual codes for apartments
3-key programming for entry
4-erasing keys from memory
*-exit mode
#-confirmation of installation (saving changes).
1,5,6,7,8,9,0 - does not exist.
Try to encode the key for yourself (an example is given if the master code came up):
#999 (2 spades) 1234 (1 spades) 3 (1 spades) (apartment number) put the key (beeped) # and then * .
VIZIT intercoms also have a special mode in which you can change everything - even the master code. The transition to this mode is carried out from the normal state as follows (taken from the instructions):
1) power off the intercom
2) disconnect the two "programming" wires in the central unit
3) turn on the power.
As can be seen from the above, the block with the buttons must be removed.
Intercoms Metakom
Door opening:
B-1-B-5702
B-5-B-4253
B-6-B-4568
B-1234567
65535-B-1234-B-8
Changing system passwords:
65535-B-1234-B-9-3-new code-B = Change master password (default 1234)
65535-B-1234-B-0-new code-B = Change shared password (default 1234567)
65535-B-1234-B-B-flat number-B-0-new code-B = Changing the apartment password (for each one, by default 4 characters)
Working with keys:
65535-B-1234-B-B-flat number-B-7 = Record key to apartment No.
65535-B-1234-B-B-flat number-B-7-0-111 = Remove all keys from apartment #
65535-B-1234-B-9-7-111 = Delete all master keys
65535-B-1234-B-9-9 = Writing a new master key
65535-B-1234-B-9-9-0-111 = Deleting a new master key
Entry codes to the intercom menus:
65535-B-1234-B = Service menu
65535-B-1234-B-B = User Menu
65535-B-1234-B-9 = System menu
Well, that's all, the material was created with the help of Leonid Vladimirovich Sedunov
(worker in intercom support), methods have been tried
Thank you for attention.
A detailed FAQ about opening some models of intercoms, how to register your key, how to change the password. The most common models of intercoms.
Q: How can I call from one handset to another?
A: None.
Q: Can I call from the handset to the intercom?
A: Yes, but first you need to get into the engineering menu of the intercom.
Q: How can I eavesdrop on the conversation?
A: You can eavesdrop simply by getting close to the line.
Q: How to clone a tube?
A: Open the body of the pipe, there are several jumpers that set the number of the apartment, there is a pipe installed in the bark (relevant for Rainkman).
Q: How to enter the Cifral intercom service menu?
A: Press any number and hold until the inscription appears, then enter the engineering code.
Q: How to enter the Cifral intercom system menu?
A: Press the bell and hold until the inscription appears, then enter the engineering code.
Q: How to enter the service menu of the Rainmann intercom (Rainmann 2000 etc. and others)?
A: You press the "key" button and enter 9 8 7 6 5 4, you should hear a double beep. Then enter 1 2 3 4 5 6 , the letter P will appear. You have entered the intercom control system. Now remember:
1 - Advanced intercom settings, I advise you not to dig there yourself, but simply enter this menu and go drink pYvo nearby. Perplexed tenants will do everything for you.
2 - Normal intercom settings.
3 - Signaling.
4 - Door lock.
5 — ????
6 - ???? (intercom hangs)
7 — ????
8 - Open the door.
9 — ????
This only works if the settings are not touched, instead of 987654 there may be another code.
Plows on intercoms where on the screen the dot is on the left.
Q: How to enter the service menu of the VIZIT intercom?
A: #999 - beep 2 times - (master code, default 1234) - beep 1 time
if the code is not correct, then it will beep with a two-tone signal
button values:
1 — ???
2 - Setting individual codes for apartments.
3 - Programming keys for entry.
4 - Erasing keys from memory.
5 — ???
6 — ???
7 — ???
8 — ???
9 — ???
* - Exit the mode.
# - Installation confirmation.
Q: How to enter the Eltis intercom service menu?
A: Same as Cifral.
Q: How to enter the service menu of the METAKOM intercom?
A: Dial 65535 V (or #) on the keyboard, then 1234 V (or #) if everything is fine, the display will show .
Q: How to temporarily disable the intercom with a tablet key?
A: We take a piece from an electric lighter, and give a discharge to the key receiver, it rarely helps, it is better to use a shocker.
Q: How to reset the intercom memory?
A: To do this, you need to find where the intercom is powered from, usually in a shield on the first floor, there is a small block there, it is usually very well hidden, just give it to zero at 1, 6, 8 and 12m +1.5 volts and -2 leg and intercom memory will be as clear as a baby.
But the specialist will restore it in 5 minutes.
There is also a COM port, but it is not known how to use it.
Q: How to open the Cifral intercom door?
A: If there are apartments with numbers 100, 200, 300, 400, etc. in the entrance, then you can try to enter:
call 100 call 7272
call 200 call 7272
call 300 call 7272
call 400 call 7272
call 500 call 7272
call 600 call 7272
call 700 call 7272
call 800 call 7272
call 900 call 7272
call 100 call 7273
call 200 call 7273
call 300 call 7273
call 400 call 7273
call 500 call 7273
call 600 call 7273
call 700 call 7273
call 800 call 7273
call 900 call 7273
Q: How else can I open Cifral?
A: CALL 41 CALL 1410
Or just enter 07054. Sometimes it helps.
Q: How can I open the Eltis intercom?
A: B 100 B 7273
V 100 V 2323
You can also try options from Cifral.
Q: How to open the VIZIT intercom door?
A: If the default settings were not changed then *#4230 and the door will open.
Sometimes 12#345 also helps.
Q: How to enter the system mode of the VIZIT intercom?
A: To enter the system mode, you need to connect the terminals of the PROGRAMMING cable, most often for this you need to remove the entire unit from the door, because these inputs are not output to the shield.
Q: What is the difference between service and system mode?
A: Service and system modes are different. If you remove the block from the door and turn on the system mode, you can change everything. Even the master code to enter system mode.
Q: How can I save my key to the memory of the VIZIT intercom?
A: In programming mode, press 3, then the house number, apply the key, press # and then *
Q: What are the default codes for intercoms?
A: 1234, 6767, 3535, 9999, 12345, 0000, 11639 (VIZIT).
Q: How to open METAKOM?
Q: How many master keys can a METAKOM intercom have?
A: Only 1.
Q: Can the keys to the intercom be killed with a magnet, or at least cripple?
A: No, you can't.
Q: How to change the system code in the Cifral intercom?
A: In programming mode 1 (p----) and enter a new pass.
Q: Are there special intercom codes for opening doors by special services?
A: No, there are no such codes.
Q: How can I store my key in the memory of the Cifral intercom?
A: In the service mode, press 5, then enter the apartment number, the intercom will write TOUCH, apply the key - it is in memory.
Q: How to erase the tablet key from the memory of the Cifral intercom?
A: In the service mode, press 5, then enter the number of the apartment to which the key is connected, then press 9.
Q: How can I store an optical (flat with holes) key in the memory of the Cifral intercom?
A: In system mode, press 5, then enter the key cell number (1, 2, 3), insert the key, press the bell.
Q: How to change the common code of the Cifral intercom?
A: In the service menu, press 2, then enter a new code, if the code is shorter than 4 digits, then press the bell after entering.
Q: How to change the individual code of the Cifral intercom?
A: In the service menu, press 3, then the apartment number, call, enter a new code, call, then the call will go, the subscriber will have to press the call button twice.
Q: How to disconnect the Cifral intercom subscriber?
A: In the service menu, press 4, then 0, then the apartment number, then call.
Q: How to connect a subscriber who was disconnected from the Cifral intercom?
A: In the service menu, press 4, then 1, then the apartment number, then call.
Q: What are the default settings of the Cyfral CCD-2094M intercom?
A: The access code for changing parameters and settings is 123456.
General code 1234.
Individual code table number 000.
Number of the first subscriber 1.
Number of subscribers to be served 100.
Signal duration Z 1.
Common code usage mode ON.
The mode of using individual codes is ON.
Subscribers ON/OFF.
to the service list Horn #3.
Notification of the subscriber about opening the door with an individual key ON.
Q: There are no * and # keys on the VIZIT intercom, what should I do?
A: There are C and K. C - * K - #.
Q: Is there a system menu for old intercoms (with a “stick” key)?
A: No.
Q: How else can I open the intercom doors?
A: Try shorting out a light bulb in your driveway, it helps sometimes.
A: We put one foot where the door opens and strongly pull the handle when jerking the door opens.
A: You press any key from another intercom and enter 8082 key 5454
A: One dot is lit on the working intercom. Then press the button with the image of the key, "---" will appear on the monitor, enter 987654 (a double beep is heard), then enter 123456. If the letter "P" appears on the monitor, then you have safely taken control of the intercom. Now you must determine the purpose of your work. If you just need to open this door, press the number "8" and the door will open.
Q: How to open intercoms with touch keypad
A: While it's winter, intercoms with a touch keyboard are affected by a super trick. We take a normal lump of snow, and lean it against the keyboard. We wait until the inscription "Err" appears on the display, go
Q: How to open VIZIT BVD-342
A: I entered the menu (I dialed #999), 1-2 appears on the screen, press 1, it seems to enter.
Q: How to open METAKOM?
A: In the service menu, press 8. Also helps B (or #) 1234567.
A: 65535-B-1234-B-8 or B-1-B-5702 or B-6-B-4568.
A: Press the call, then the number of the first apartment in the entrance, call again ("COD" will be displayed), then 5702 ... The door is open!
For Faktarial intercoms, the code (for everything): Press 5 (1,2,3,4,5,6,7,8,9), the numbers go out, quickly enter: 254525, press K (B), then by 4 (1,2,3,4,5,6,7,8,9) and again by K (B)
Manufacturers paid special attention to this particular part of the system. However, the implementation of security management is not always reliable, which allows how to open intercom without key , so do intercom hacking any brand.
And most importantly, that each of the readers clearly remember: intercom opening if such a need arises, this is an acceptable matter, and intercom hacking with mercenary purposes is punished already according to the criminal code. And when the main purpose of searching for material on how to hack an intercom was just such plans, then look at the same time for the latest edition of the Criminal Code of the Russian Federation.
In this article, we will review information on opening intercoms the following types: Barrier II, IIM and 4; VISITS ( various models); Cyfral (various models); Eltis; METAKOM; Rainmann; DomoGuard; blink; T Guard.
Hacking intercoms Barrier II and IIM
An old Russian intercom similar to the "Barrier" with a mechanical lock and a flat magnetic key can currently be found no more often than a mammoth. Although - anything can happen, and such an intercom may well be in one or another no less old house. For models 2 and 2M, there is an unchanging opening code - 1013. Although, roughly speaking, the intercom is opened without problems by a pair of small magnets, which are enough to move around the area to apply the key.
Barrier - 4
The fourth intercom model of this type is single-user, it was installed in entrances with concierges. As a result, it will not be possible to dial a non-replaceable code, but you will have to chemise with magnets to the bitter end. The key of this intercom has 3 magnets.
How to open an intercom without a key vizit
Slightly more difficult in terms of opening are considered intercoms visit. The codes on them differ in a solid variety. Often there are no * and # keys on the keyboard, instead of them the C and K keys are used, respectively.
If the usual settings of such intercom have not been changed by the installer, then the door should open when entering * # 4230 or 12 # 345. Opens newly installed intercoms visit code *#423 or 67#890
How to hack vizit intercom through the service menu: dial #999 - this is the entrance to the service menu, wait for 2 short beeps, then enter the master code (default 1234). The intercom visit, which is being hacked, should react with one short squeak. If you used the wrong code, the signal will become two-tone. In such a situation, it is possible to try the usual varieties of master codes - 6767, 3535, 9999, 0000, 12345, 11639.
After entering the warranty menu, it is possible both to open the intercom visit and to perform a number of slightly more difficult operations.
So, composition 2 - pause - # - pause - 3535 - a command to open the intercom door without a key.
Key "3" is configured to program keys for the intercom. After pressing key 3 in the service menu, you need to attach the key to the reader, press # and wait for a squeak. Everything, the key is entered into the memory of the intercom.
Button 4 erases the keys from memory.
* - exits the current mode.
# - used to confirm configurations.
A little harder to open intercom "Visit" BVD-3xx - without display and indication LEDs. To open the door, you need to press 1 in the service menu. True, sometimes breaking into the intercom The Visit will be successful in the case of the BVD-34x model (with a left-hand receiver).
How to open a Cyfral intercom
To open the intercom Cyfral you need:
a) in the event that there is living space in the entrance with a numbering multiple of Hundred (Hundred, 200, 300, and so on), then the code is tedious to enter like this: call button (code 1) call button (code 2). On the spot (code 1) it is necessary to enter the number of living space multiple of 100, and on the spot of code 2 - 2323, 7272 or 7273.
b) for intercom models with the letter “M”, it is possible to try the code “call button 41” or “call button 1410”. Sometimes the door opens if you just enter 07054.
Intercom CCD-2094.1M open differently. It is possible to distinguish it by a burning or flashing line on the screen. If you dial the code “call 0000”, either it will immediately open up, or you will enter the warranty menu (the inscription ON on the screen), after that you must press 2, after which the door will open. If OFF appears, the fast entry mode is disabled. This means that the installer was operating, which has long been mounting Tsifral intercoms. Access codes, in accordance with this, were changed by him.
Intercom Codes Cyfral CCD-2094M
In order to open the intercom of this type, you must dial the code "0000 call key". The monitor should show the inscription "cod". It is necessary to use the code 123456 "Call" or 456999 "Call", sometimes the composition 123400 "Call" is used. We wait two to five seconds. If the inscription “f0” appears on the monitor, then access to the system menu is open. In order to open the door, you must use the code 601.
If there is a desire to visit this intercom (more precisely, its owners) often, then it is better to enter into the memory of the intercom a personal key suitable for intercom "Cifral". To achieve the desired result, it is necessary to press the call button and keep it pressed until an inscription appears on the monitor, announcing the entry into the service mode. After that, we press the "five" and enter the number of the living space available at the entrance. The inscription on the monitor should change to TOUCH. When this happened, we apply the key. If a model with an old optical key comes across on the way, then instead of the living space number, you need to dial 600, then insert the key and press the call key.
How to open the intercom Eltis
Intercoms Eltis, codes for which do not differ in variety, it is enough just to open. There are 2 options for service combinations that will provide “neat hacking” of the Eltis intercom: “call button 100 call button 7273” or “call button
One hundred call button 2323". If the hacking of the Eltis intercom did not succumb to such compositions, it is possible to try options from the Tsifral intercoms.
How to open the intercom METAKOM
Hacking the Metakom intercom is done according to the following scheme: you need to press the call button, then use the number of the first living space in the entrance and press the call again. “COD” should appear on the monitor. After that, you must use the code directly - 5702. If this technique does not work, then try the compositions 65535 call button 1234 call button 8 or 1234 call button 6 call button 4568.
And also - about how to hack an intercom Metakom MK-20 M/T without dancing around the keyboard. In this model, roughly speaking, there is no and will not be a system of protection against the use of master keys. As a result, if you bring a “pill” without firmware to the intercom reader, it will automatically enter the programming mode. If there is no pill, it is possible to persuade him to open using the numeric keypad. Intercom code Metacom brand MK-20 M / T codes can be “call key 27 call key 5702” or this “call key 1 call key 4526”.
How to open the Rainmann intercom
Models Reinmann 2000, also those intercoms of this brand that have a dot on the left on the monitor can be opened like this:
Press the "key" key on the numeric keypad and enter the code 987654. In response to this operation should be a double beep. After that, we enter the code 123456. The letter “P” should appear on the screen, which actually indicates the entrance to the service menu.
Entrances are trying to protect from outside penetration. This was done not only for the purpose of preserving the finish. staircases, but also that there was no free access to the apartments. Sometimes residents of the entrance cannot find their magnetic key, and familiar neighbors are not at home to contact them. In such situations, a certain set of buttons will come in handy as a “master key”.
Protection modern home
Firms producing intercoms provided in their creations the possibility of using a digital code that plays the role of a “magic key”.
Note! Use a "digital master key" if necessary, since the introduction of an electronic key for other purposes is punishable by law.
Different equipment has combinations, there is no common code. Let's analyze the popular brands of a protective public access lock:
- Vizit (Visit);
- Metacom (Metakom);
- Cyfral (Digital);
- Forward (Forward);
- Eltis (Eltis);
- Factorial (Factorial);
- Marshal (Marshal);
- Lascomex (Lascomex).
And do not forget that there is always the opportunity to call neighbors who know you, asking them to help in this situation, so as not to remember or write down the code. You can not use master keys, as they will disable the entire mechanism.
Important! After entering the "universal master key", for some time the electronic entrance lock will stop functioning correctly.
How to open a Vizit intercom (Visit) without a key
Vizit (Visit) produces a variety of modifications of equipment designed for many and few apartments. The former are used for 200 apartments, the latter for private ownership, for example, mansions or summer cottages.
All models come with regular firmware, so before changing the code, it opens with a common set of numbers. There are several opening methods:
- *#423;
- 12#345;
- 67#890;
- *#4230.
If there are no “*” and “#” buttons on the equipment, dial “C” and “K”.
In addition to dialing numbers, it makes sense to use the features of the equipment menu by dialing #999. When you hear two intermittent signals, enter 1234, if it does not pass, then try to dial: 0000, 9999, 3535, 12345 or 6767. The correct entry will confirm the opening of the "high-rise building".
And the last way:
- Cash in on "2" and expect a little.
- Then, on "#" and also wait a bit.
- Enter "3535" and the entrance will open.
To exit the equipment menu, press "*".
Please note that models where there is no screen or LEDs are more difficult to open. A special key is required. Or hold down "1", then try the code. Such a "miracle of getting" into the entrance does not always happen.
How to open a Vizit intercom (video)
How to open a Metacom intercom (Metakom) without a key
Metacom (Metakom) produces digital modifications, where there is a panel and a processor, with a built-in power supply. One device can store up to 508 IDs. In addition to opening with an individual key, there are also "universal digital master keys".
First opening option:
- press "B";
- enter the number of the first square. at the entrance (usually the numbering is above the door leaf);
- again "B", "code" will appear;
- dial the digital key 5702.
If these actions did not give the desired result, here are a few more options:
- 65535V 1234V 8.
- 1234V 6V 4568.
- V 27 V 5702 (for model MK-20 M/T).
- В 1 В 4526 enter an empty identifier for the reader into the equipment memory.
The video below shows the options on how to get to the entrance.
How to open the intercom Cyfral (Cifral) without a key
There is no single keyless opening system for Cyfral devices.
There are not so many ways:
- Where there are apartments with a number of 100 (200, 300, and so on), the code is applicable: B - square number ending in 00 - B - 2323, 7272 or 7273.
- If there is an “M” marking, then dial the following: B - 41 - B - 1410. There are models where it is enough to enter 07054.
- With the designation "CCD" - 2094.1M, try B - 0000. If after the combination the door did not open, but the inscription "ON" appeared, press "2". When the inscription “OFF” appears, it makes no sense to enter standard codes, since they were replaced by installers.
- With the designation CCD - 2094M, you need to dial 0000 - B. Then, the inscription "cod" will appear, where you need to click on the numbers 123456 - B or 456999 - B. You can apply another option: 123400 - B, after the appearance of "F0" add 601.
Here is a video of the opening of the 2094.
How to open the intercom Forward (Forward) without a key
Electronic locks from Forward (Forward) can often be found in our homes, so common codes may come in handy. Here are some sequences:
- K - 557798 - K (K is the key, it can be in the form of an image);
- 2427101;
- 123*2427101;
- K - 1234.
Use the menu and add a key. Press sequentially on 77395201 * 0 *, apply the key that is, and twice on "#".
Here is a video on the topic:
How to open the intercom Eltis (Eltis) without a key
For Eltis devices (Eltis) there are simple combinations of numbers and buttons:
- B - 100 - B - 7273;
- B - 100 - B - 2323.
For some modifications, the Cyfral intercom codes (Cifral) given above are applicable.
Here is a list of opening options in the video:
How to open the intercom Factorial (Factorial) without a key: codes for opening
There are few digit sequence options for Factorial equipment. Try typing 000000 or in ascending order from one to six. There are situations that the opening is not feasible, since it is required to change the cipher.
You can dial 5, you will see “180180” on the screen, click on the call - 4 - call.
Below is a video tutorial:
How to open the intercom Marshal (Marshal) without a key
Quite popular in Russia is the Marshal brand (Marshal), designed for a large number of premises.
There are simple combinations, but the "wonderful" penetration into the entrance does not happen every time. First enter the number of the last square. at the entrance + 1. For example, the last 60, then dial 61. Then two options: K - 5555 or K - 1958.
How to open the intercom Lascomex (Lascomex) without a key
The last company on the list is Lascomex (Lascomex). These devices are not uncommon in door leafs high-rise buildings in Russia. The equipment has a unique feature - a four-digit code is set during installation. Write it down and enter: B - No. kV. - figures for the entrance.
Second option:
- Alternately press the "0" and K buttons four times in a row.
- Click on 6 four times.
- "P" will appear, enter 8.
- After 60 seconds you will be able to enter.
In order not to constantly enter numbers, remember the codes, reissue the standard magnetic "opener" for the entrance door.
Finally
Intercoms are installed on almost all entrances, so everyone faced the situation of the absence of a magnetic key. Try to call familiar neighbors first so that they open the door.
If no one is at home, enter the special code corresponding to the model and manufacturer of the equipment. Sometimes it may not work, then you have to wait until someone else opens the front door.
You may also be interested in:
Video intercoms for a private house: nuances and pitfalls 
Video peephole for front door– security of property 
Video intercom for an apartment with connection to the entrance intercom - find out who came
This type of protection against strangers is installed in high-rise buildings. Sooner or later, apartment residents ask themselves the question: “How to open a Metacom intercom without a key?”. But since this view is well protected from breaking, it will be difficult to open the doors. But probably.
Metacom Features
To open any intercom, you need to understand the principle of its operation. Call panel includes:
- controller;
- key reading system;
- subscriber intercom;
- and a panel with numbers.
Metacom keys are distinguished by their reliability. It is simply impossible to open the lock of this company with another device. Each key includes a chip with a code that does not change.
The price of Metacom does not bite, and the intercom itself is easy to use.
The shockproof housing protects the device from hacking. Impact weather conditions, as well as temperature changes will not damage the Metacom intercom.
Combinations
Now many are looking for an answer to the question of how to open an intercom without a key. Fortunately, there is such a way. And there are several of them, because specific model suitable combinations. Although there are such algorithms that can fit all Metacom intercoms.
There are three types of menus:
- User: "65535" - HF - "1234" - HF - HF.
- Service: "65535" - KV - "1234" - KV.
- System: "65535" - KV - "1234" - KV - "9".
Method 1
What to do:
- Call button (KV).
- No. of the first apartment in the entrance.
- The word "code" will appear.
- "5702".
Method 2
What to do:
- "65535"
- "1234".
- "8".
Method 3
What to do:
- "1234".
- "6".
- "4568".
Method 4
(for Metakom MK-20 M/T)
What to do:
- "27".
- "5702".
Method 5
What to do:
- "1".
- "4526".
- Bring a new key and register it.
Programming
Signing in with a universal code is not always possible. So the only solution is programming and registering new code.
What to do:
- For memorization new apartment: "65536" - C - sq. no. - "7".
- To remove the old code from this apartment: "65535" - C - "1234" - C - C - sq. - KV - "70111".
- Deleting Master keys: "65535" - C - "1234" - C - "97111".
- Identifier entry: "65535" - C - "1234" - C - "99".
- Removing the old identifier: "65535" - C - "1234" - C - "990111".
Important! Now the most popular solution to situations with closed doors is the universal key. All possible firmwares that are used to open intercoms are immediately entered into it.
Video
The video below shows several ways at once how to open a Metacom intercom.
Opening the intercom Cyfral (Tsifral)
It was not by chance that I started with this particular brand: there is a model in my entrance Cyfral CCD-2094(according to some reports, this is one of the most common models in Russia, and also outdated). You can open such a door without a key using one of two methods:
1 - Press: 0000 , after which the inscription "COD" should appear. This is a code request to access the service menu. One of these should fit: 123456 , 123400 , 456999 . Press the call button and wait for a response. If the inscription “F0” lights up - Hooray, we managed to enter! Now enter the code 601 and the Digital is open!
2 - This option can only be used if there are apartments with numbers 100, 200, 300, 400, etc. in the entrance. For example, I will take the number 200. What are we doing? We press the button: "B" - then the apartment number: 200. Then again "B" and the code: 7272. That is, it turns out like this:
B-200-B-7272
If the door does not open, try these options:
B-200-B-7273 B-200-B-2323
Video instruction:
For model CCD-2094M, code may be triggered 07054
. There were also cases when it was possible to open the intercom by pressing the buttons "B" + 41 and "B" + 1410.
In the case when you need to open the “Digital CCD-2094.1M” (you can recognize it by the screen where the dot is flashing or lit), you must enter the following code: “Call” + 0000. So you will get into the service menu and the inscription "ON" will light up. Press button 2 to activate the "quick entry" mode.
If the word “OFF” lights up, then the mode does not work and the Cyfral hack will not succeed because the master was “explored”.
Note:
If necessary, on the CCD-2094M model, you can try to program your key for the Tsifral intercom. You need to press the call button and hold until the device enters the service mode. Then click on the five (5) and the number of your apartment. We look at the screen. The inscription "TOUCH" should appear - it indicates that you can apply the "tablet" of the key. After you do this, the key will be recognized and open the lock.
Audio intercoms Vizit (Visit)
As it turned out, the “Visit” intercoms are the most resistant in terms of access codes or hacking. The most common models are BVD-313 and BVD-311. Modern - BVD-343 and BVD-344 are rare. By the way, they already have additional protection from unauthorized management of especially zealous tenants.
During installation, in most cases, the standard settings are usually not left, and it will take a very long time to select the Visit intercom code after that. If you are lucky and the installers cheated, leaving the default settings, then in order to open Vizit without a key, try the codes:
Old models - *#4230 or 12#345 New models - *#423 or 67#890
An example of how the code works on the old model:
Also, sometimes these options are rolled:
#196 #999-1-1-5555-Star-#999-2-1-1-Star-#5555
You can try to hack the Visit intercom by entering the service menu through code # 999, after which two beeps should follow. Now you need to enter the master code of the device. We hope that the installer was lazy and enter 1234. Didn't fit? Then try: 12345, 0000, 9999, 11639, 3535, 6767. If you're lucky, one short beep will follow and you will be taken to the service menu. To open the door of the Vizit intercom without a key, you need to dial the numbers:
2-pause-#-pause-3535
Video opening example:
By the way, if your Vizit intercom does not have “#” and “*” buttons, then do not be alarmed, instead of them there are, respectively, “C” buttons - this is an “asterisk”, and “B” or “K” is a “lattice” .
Note:
To program your key, you need to press the "3" button in the service menu and attach it to the device. After that, the key fob will be added to the database. The main thing - do not press the number "4" - this will erase all the keys from memory. To exit the mode, press the "*" (asterisk) button, and then - "#".
How to open an intercom with a Metacom code
In order to open the Metakom intercom without a key fob, you can try to enter the following options:
65535 - "B" - 1234 - "B" - 8 1234 - "B" - 6 - "B" - 4568
Also, there is information that codes may come up:
"B" - 1 - "B" - 5702 "B" - 6 - "B" - 4568 "B" - 5 - "B" - 4253 "B" - 1234567 "B" - 1803
Video instruction:
It did not work, then we try to enter the service mode. To do this, you need to find out the number of the first apartment in the entrance. After that, press the "Call" button and hold until the inscription "COD" appears. Now we press the numbers - 5702 and ... the door will open.
Note:
I have repeatedly met information on the Metacom MK-20TM model on the network. According to the information provided, it does not have any protection against intercom hacking. Therefore, if you poke it with a clean, unprogrammed key, it will go into engineering mode and automatically unlock the door.
How to open the intercom Eltis
To date, there are only a few models of Eltis contactless audio intercoms in Russia. Their device is uncomplicated, like the firmware. Therefore, hacking Eltis among juvenile hooligans is a common thing. To open the door, try entering the code:
Call - 1234-2-1-3-3-123
In the case when the attempt ended unsuccessfully, then try these keys:
100 - Call - 7272 100 - Call - 7273 100 - Call - 2323
Just as an option, you can try the Cifral codes.
Opening Barrier II, 2M and 4
These are very old models of intercoms. And that is why they are often still found in the old nine-story buildings and five-story "Stalinka". In new buildings you will not find such a 100%. In the models "Barrier 2" and "Barrier 2M" to enter the entrance, you must press the buttons "1" and "3" or "1" and "0". Sometimes you can open the door simply by moving the magnet around the place where the keys are applied. For the model "Barrier 4" universal keys Or no codes at all.
Other brands of intercoms:
Rainmann and Raikmann intercom codes
Despite some similarity in names, Rainmann and Raikmann intercoms are completely different devices. Raikmann devices are resistant to burglary and opening without a key using the code on them is impossible. But the Rainmann CD-2000 and AO-3000 models are found.
In order to open the 2000th model, you must click on the "key", then enter the code "987654". After that, the intercom will beep and you must enter the numbers "123456". If the engineering menu is available, the “P” icon will appear on the screen. Now, to unlock and open the door, you need to press the number 8.
It’s better not to reap anything else - you can cut down everything and rake “by the hat” from the residents.
Another life hack that users have noticed is the reaction of the touch keyboard to hypothermia. If you roll a snowball, attach and hold for 15-20 minutes, then there is a chance to open the door.
Factorial
The setup of intercoms of this brand is very, very similar to the already familiar Cifral, with the only exception that when installing the device, it necessarily requires changing the master password and therefore it is considered that it will not work to open it. Although it may turn out to be a hacking option through the engineering menu. To do this, you need to dial the intercom code Factorial. In most cases, these are used:
000000 123456
Another option is to press the "5" button and hold it for 5-6 seconds, then type this:
180180 + "Call" + 4 + "Call" key.
Laskomex (Laskomex)
To open the door on Laskomex AO-3000 VTM, try entering the keys:
1 + "Key" + 8976
66 + "Key" + 1989
Didn't fit? it means the code was changed during installation.
To enter the service menu, press the key 5 times, after which a password entry field will appear. By default, this is used: 1234. Most often, it is changed when you can, but there is still a chance. The code P8 is responsible for opening the Laskomex AO-3000VTM door.
DomoGuard
A rare guest in our high-rise buildings. It is extremely rare.
To open the door of the Domogard intercom, make one long press on "C". After it makes a sound, quickly enter the code:
669900 + "Call" + number last apartment at the entrance plus 1
After that, the screen will display the inscription: "F-". We are inside the service menu! You can then use one of the following options:
080 - Open door 333 - Save new key 071 - Disable door lock
Blink
This is not access intercoms, but individual, used most often in private homes or where there is a concierge. There are no universal codes for it.
T-Guard
Another rare model. There is only one single hack option:
"Call" + 00000 + "Call"+"Call"
The last two calls must be pressed quickly and the access intercom will open.
Forward (Forward)
There is very little useful information on Forward intercoms on the network. There are only three well-known universal keys that have been unearthed:
123*2427101 K+1234 2427101
In order to program your key for the door under "Forward", you can try to enter "77395201"+"*"+0+"*". After that, we apply the key tablet and press the "#" twice. If the code "77395201" did not work, try this one: "5755660".
Condor
There is no information on master codes for the Condor intercom.
KS intercom
There is very little information on how to open the KS-intercom. The only code I could find:
"K" + "377" + pause + "698" + "K"
There is also information that sometimes the code works:
"K"+0000 "K"+9999
"K"+ 0000 + pause + 98 "K"+ 0903 + pause + 98 + pause + "K"
Unfortunately, they don't always work either.
Video: opening the intercom "KS":
Techcom
There is information on the network that it is not so easy to open the door of Techcom. In some cases, the following may work. Be sure to need a key to such an intercom. We hold down the three buttons "1", "6" and "0". After that, we release one by one. We start with "0", then "6" and "1". A signal will sound. Here we enter the default pass - "4321". If the password came up, click on "Challenge", then on "3" and again "Challenge". We bring the key and the door will open. I myself have not tested this method, I cannot vouch for it.
Impulse-DS
There is very little information on Impuls-DS intercom models. Possible options:
"1234"+"C" "B"+"99911"+"B"
The first option almost never works, because. the code will definitely be changed when the device is installed.
Golden eagle
Access intercom Berkut LS 2001 is the only model of this manufacturer on the market so far. From itself, it is a simple device based on an oscillatory circuit, which is assembled on a resistor and a capacitor. Universal codes
"key" + 123456 + "key" + 5150С "key" + 123456 + "key" + 206С "key" + 123456 + "key" + 6140С "key" + 123456 + "key" + 2589С
Also, you can try to make your own master code. To do this, we type the command: “key” + 23456 + “key” + “XXXX” the “F” icon will appear. Now click on "9" and "key". Then you can enter your 4 digits.
Leader-M
These devices have been out of production for a long time. Unfortunately, there is no information on how to open Leader-M at all.
Keyman (Keyman)
At the time of this writing, there is only one known master code for the Keyman intercom:
"K"+100+789+123456+8
In some cases, it rolls the input without the last eight. Video guide:
Marshal (Marshal)
To open the intercom Marshal, you need to enter a number equal to the number of the last apartment in the entrance +1, and after that - “K” + “5555”. That is:
"Number+1" + "K" + "5555"
Works once.
Coral Intercom Service
Devices are extremely rare. Only two master keys for Coral-Service are known:
123 + "beep" + "1234"
"00"+"beep"+"773952004"
Kamsan (Kamsan)
There is no universal master code for KamSan intercoms, namely the KS-2002 model. There is no information on their programming. It is only known that it will automatically switch to programming mode if an empty blank key is attached to it.
Commax (Komaks)
In the entrances you can find two models of this manufacturer - COMMAXCDV-50A and COMMAX CDV-50AM. Their device is very complex and almost no one managed to open its security. The only code I could find is this:
"K"+"C" + "K"+"C" + "K"+"C" + "K" + "K"
Kocom (Intercoms What or Kokom)
Information on models of this manufacturer is not available.
Belsplat (Belsplat)
At the time of this writing, there are no keys to open the Belsplat intercom.
Pirrs (Piers)
In the entrances there are models "Pirrs 1000 Micro", "Modern" and "Lux". Factory master code for all three types:
"12345678" "K"+"1234"
For the Pirs 1000 Micro model, the key may also work:
"8310649" + "entrance number"
There is evidence that these models of audio intercoms allow you to put your own code. It is done like this:
Enter the master code "12345678". If it has not been changed, an audible signal will sound. Press the door opening button, and without releasing it, press the number “5” on the keyboard. The confirmation tone for entering the settings should sound again. Release the door open button. Now you need to enter your code - 987, for example. The main thing is that there should be no more than 8 digits. Moreover, the sequence of the first two digits should not coincide with the master code or apartment number in the entrance. After finishing entering the code, first click on the "asterisk" and twice on the "grid". After that, the intercom can be opened with the code: "987"+"*".
Secret
In real life, you can find only one intercom model - "Secret-999". There are no codes for it. Not hackable.
Arcades
In fact, the intercom Arcades is a slightly modified model of the COP, which I have already considered above. Accordingly, codes from KC should also work for him.
SmartEL
There is no information on the codes for the SmartEL brand intercom.
Cron
By default, the key "951" is used, but there is almost no chance that it has not been changed. Hacking Cron audio intercoms is impossible, since nothing can be done without an individual master key.
Stroymaster
There are no universal codes for these devices. The only thing you can do is try to enter the system menu and put your code. But for this, you first need to study the procedure for programming a new key, which is very time consuming. Well, then you will need to press and hold the "B" button until the inscription "SYS" appears. After that, you need to enter a password. The default is: "1234". If it doesn't fit, then you're out of luck. Approached? Excellent! Program the key according to the instructions and use it!
Attention! If you tried to apply the code indicated in the article for your intercom and it did not work, you do not need to write angry comments. I make no guarantees. What works in one entrance is not at all a fact that it will work in another. In addition, installers have become smarter lately and, having eaten enough problems from juvenile hackers, they began to change passwords and master codes.
