Hand trimmers mow vegetation either with a fishing line or with knives. At the beginning, the functionality of the trimmer is limited to mowing soft grass with normal and low height, since plant debris is wound onto a flexible shaft, or in other words, sticks to the spool. By installing a trimmer blade, it becomes possible to cut off tougher trunks and trim young bushes.
Types and uses of trimmer knives
The systematization you will like is carried out according to the following characteristics:
- Based on the material of the knife: iron and plastic knives are known. The choice is often limited not so much by the user’s desire as by the power of the drive - iron blades are heavier, and the trimmer shaft equipped with them develops more slowly, which adversely affects the durability of the motor. But the cutting ability and durability of iron knives is much higher than that of plastic ones.
- Upon completion cutting edges. They are distinguished by significant diversity, and as a rule they come with 4 or more teeth, single or different heights, and also solid or with technological holes.
- According to the shape of the knife itself, which has a solid disk blade, or is made in the form of several blades with a similar distance between them.
The choice of the size and design of the trimmer blade depends on the intended purposes, the type of rod and the power of the motor. If the trimmer rod is bent in the shape of a letter J, then there is no need to use a metal knife, since if it comes into contact with a powerful obstacle, nettle, stone, trimmer will be sharply thrown back, towards the mower. Then even the highest restrictive casing will not save the worker from a leg injury. On trimmers with a straight shaft, the rebound distance will increase.
Plastic trimmer blades, although less durable, are quite capable of cutting most types of grass. In addition, their increased elasticity does not create additional loads on the flexible shafts of electric trimmers.
The configuration of the cutting edges determines the quality of the cut. For tough grasses, dead wood, and woody shoots, disc blades with the largest number teeth: then, regardless of the speed flexible shaft, the cut will be clean and even. The inertia of perforated knives is significantly less than solid ones, and this does not particularly affect the durability of the tool, taking into account the fact that the tool is made of high-quality tool steel. The exception is cheap Chinese-made products: knives there are made from any steel.
Where and which knife is better?
When the fishing line’s capabilities are not enough, you should think about replacing it with a metal or plastic knife. If a replacement knife is included with the trimmer, there are no problems: replacing the cutting equipment is done in accordance with the instruction manual for the trimmer. However, this does not happen every time.
Read also
Find out the suitability of installing a knife on an existing electronic trimmer(there will be no similar problems with gasoline) there is an option for the actual speed flexible shaft. If, when replacing the spool with fishing line on the knife, the engine reaches the set number of revolutions per second or less, then a replacement is likely, otherwise the engine will overheat very much, and the trimmer gearbox will quickly fail.
It is interesting to compare three more common variants of knives with each other - a multi-toothed disk knife, also with 2 and 3 blades.
Motokosa. How to replace a damaged shield.
Motokosa. How to replace a damaged shield. The shield was damaged for several days. Maybe I was unlucky. B high
Metal disc knives
Usually, several of these knives are included in the trimmer kit, but you can also purchase them separately by measuring the outer diameter of the knife and the configuration of the mounting hole. Nettle, circular cutters from Stihl and Husquarna are interchangeable with each other. Circular knives differ in the number of teeth, height (some have different heights), and also the continuity of the blade. In most cases, such knives are installed on trimmers from Stihl, Huter, AL-KO, equipped with a straight bar, and are more rigid. They cope well with old growth and long trunks, however, when working with young grass, sticking of the mowed mass is often observed on inner surface protective casing.
A trimmer with a perforated blade, compared to a solid one, picks up speed faster. Flaw circular knives- increased moment of inertia, so the starting power of the drive increases. On cheap designs and with frequent stoppages in work, this leads to overheating of the motor and negatively affects its durability.
Two-blade and three-blade knives
These are the knives that he uses to complete his electronic trimmers. trademark Bosch. Their moment of inertia is small and does not actually affect the performance of the drive. The ease of use of this design lies in the fact that separate replacement of all blades is possible. For trimmers of this type, the rod is bent in the shape of a J-shaped blade. Two-bladed knives work stably on a homogeneous mowed mass. They perfectly throw the cut shoots to the side and do not allow residues to stick or wrap around the rod shaft.
Three-blade and two-blade knives are quite competitive with disk knives in their capabilities, but the thickness of the blade should not be less than 2 mm. At the same time, forged knives are more durable than stamped ones (found on Chinese-made trimmers). It is easy to distinguish them - on stamped blades, traces from the cutting punch are clearly visible with the presence of corresponding chipping and shear zones, which is not present on forged ones.
Read also
Shark knives
“Shark” is essentially an attachment of three bladed knives, with each blade fixed relative to the other at an angle of 120°. The advantage of this design is that each blade can be customized individually. And therefore, when mowing an area with various types vegetation (grass, weeds, dead wood), the quality of mowing will be approximately the same. Today, since the interval between mowing the grass with each blade is reduced, the discarding of the grass occurs more actively. The “Shark” head is compatible with many standard sizes of electric trimmers, has a low dead weight, but requires periodic adjustment of the blades, which are attached to the base with conventional screws.
There is an option to reduce the moment of inertia of the circular knife by independently perforating its surface, nettle, on a punching press. The perforation holes are made to be placed strictly symmetrically relative to the center of mass of the knife. The tool becomes lighter, but its cutting capabilities do not change. Proper sharpening of the blades of the interchangeable knife also has a beneficial effect. It is produced at low speed grinding wheel with normal grain size. The teeth are sharpened at an angle of 30°. You should not use a trimmer knife tipped with carbide - the quality of the cut remains virtually the same, but the weight of the tool will increase.
DIY trimmer knife
Much easier homemade knife do it in a paddle design. For this purpose you will need:
- A piece of pipe (copper is better than metal) of a suitable diameter for the production of an adapter sleeve for the outlet part flexible shaft.
- A sheet of steel less than 1 mm wide for the washer.
- An ordinary cotter pin in accordance with GOST 397-66, for attaching the base to the trimmer shaft.
- Steel strips 1...1.2.4 mm wide for the production of knife blades.
- Fasteners (it is better to use rivets rather than screws or a nut for a knife, even if it is included in the original kit).
A view of a homemade trimmer knife is shown in the figure.
Manufacturing equipment is created in this order. First, the general dimensions of the device are marked so as not to go beyond the boundaries of the protective casing. Then a sleeve is made from a piece of pipe. To improve the fit, the bushing is made split and seated along the outer surface of the output part of the trimmer shaft. Since the diameter of the washer is determined only by the dimensions of the available space, it can also be selected from the nearest standard sizes. The washer is welded to the bushing in such a way that the formed seam leg is the smallest.
How make a trimmer with your own hands
How to make a trimmer with your own hands
How to get rid of ticks in a summer cottage was discussed earlier, but now the question of how to make a trimmer will be discussed with your own hands from the most available means for this.
Now on sale you can find different variants trimmers powered by both electricity and gasoline. But it is not always possible to purchase a trimmer, and in most cases, it is not really needed.
The advantages homemade trimmer from a drill or grinder, the trimmer can be easily assembled when it is necessary to mow the lawn near the house. Trimmer line, trimmer head, trimmer knife - how not to get confused in their characteristics and make right choice. When not needed, the drill or grinder is removed from the trimmer and used for its intended purpose.
How to make a trimmer from a drill and grinder
In order to make a trimmer You won't need a lot of materials and tools from a drill. There will also be no need to disassemble the drill in order to do from her manual trimmer with your own hands.
Related Posts
In addition, a drill can be replaced by cordless screwdriver, which can be connected to a car battery to increase the operating time of the trimmer.
Making a trimmer from a drill with your own hands
The main requirements for a homemade trimmer first concern its safety. The knife of a homemade trimmer is very sharp, so the presence of a protective cover on the trimmer is an indispensable condition.
The same applies to the trimmer handle on which the drill will be fixed. How to do homemade defense for a trimmer with your own hands In the summer, for a country house. The handle must be made of strong materials, of course it can be made of wood, but it is better to use an aluminum pipe for these purposes.
Protective casing for trimmer
Manufacturing of protective trimmer housing.
Motokosa. How to replace a damaged shield.
Motokosa. How to replace a damaged shield. How to make homemade trimmer protection with your own hands. How to do fuel mixture for a trimmer or lawn mower. The shield got damaged within a few days. Maybe I'm unlucky. B high
In addition, working with the trimmer after its assembly should not only be as safe as possible, but also convenient. Therefore, you should definitely adjust the trimmer holder to your height, maybe install an additional handle on the side, etc.
First, prepare the trimmer handle on which the drill should be secured. To secure the drill, you will need long bolts and metal clamps. The power cord of the drill must be attached to the trimmer handle. The wire must not dangle and pose a danger if it gets under the cutting element of the trimmer.
How to make a trimmer knife: materials
Related Posts
Homemade knife trimmer attached to the drill with a nut and bolt, which is clamped in the chuck. Be sure to remember to install a protective cover on the trimmer before doing this. casing to ensure your own safety while mowing the grass.
The trimmer blade can be made from tool steel or another very durable material. Reel for a trimmer How to make a reel for a trimmer Therefore, it is extremely important to choose. You should know that the thinner the trimmer blade, the better it will cope with cutting grass. The length of the trimmer blade depends primarily on the protective cover and the cutting width of the grass being cut. Most often, the length of the trimmer knife does not exceed 30 centimeters.
Do-it-yourself trimmer from an angle grinder
The question of how to make a trimmer from an angle grinder with your own hands is solved in approximately the same way as the production described above trimmer from a drill. How to make a housing out of a trimmer for the hole for the trimmer rod and. If you are interested in the following questions, for example: How to make a fuel mixture for a trimmer (gasoline mower). Here there is only a slight difference in attaching the grinder to the holder. Can be selected as a trimmer handle metal pipe, to which at the end you need to weld a plate with a hole for fixing the grinder with a bolt.
Small changes have also been made to the knife. homemade trimmer. In the case of using a grinder, the knife is not in the form of a long rectangle. The knife of a homemade trimmer from a grinder is made of a disc for concrete, with pre-cut sharp edges, which are specifically designed for mowing grass.
The question is how do a trimmer made from a drill or grinder can be easily solved on your own. The main thing is not to forget about safety precautions and carefully study this issue.
Only after this can you safely begin making a trimmer with your own hands.
Related Posts
Proper technical service is the key to long-term and reliable operation tool. Primitive maintenance operations include timely lubrication of the gearbox and cleaning the trimmer filter. The user should know how to lubricate the trimmer gearbox. Cleaning is done in stages: After removing the casing, the element is removed. Then it is washed with gasoline and dried...
Which useful homemade products can it be made from a chainsaw? The chainsaw is very popular among home craftsmen, as it is universal drive for unique homemade designs. Low weight and impressive power coupled with compact dimensions allows this “lumberjack’s dream” to be combined with an ice auger and...
In summer, to country cottage area looked neat, the grass has to be mowed regularly. A trimmer, a lightweight manual lawn mower in the form of a cane, helps you quickly cope with this.
A kind of electric scythe, but instead of a blade it has a fishing line.
A well-known disadvantage of trimmers is that you cannot work with them without special protection (mask and glasses): the grass scatters at high speed different sides, getting into the face and eyes.
The reason for this is the small shield above the rotating line.
To solve this problem, I trimmed the “original” plastic shield, leaving only the third part attached to the rod.
Then from aluminum sheet I made a new one with a thickness of 0.2 mm and a size of 250×250 mm, and attached it with two screws from above to the remaining part of the former shield.
Instead of aluminum, you can use a plate made of rubber or linoleum, but then the shields made of these materials will have to be secured with steel wire so that the edges do not accidentally get caught under the rotating fishing line.
Upgrading the trimmer guard
During the operation of any electric trimmer, one major drawback appears: the resulting grass juice and haylage scatter far to the sides and upwards, covering the mower from head to toe with greenery. You have to use special clothing and a mask to protect your face and eyes, but dust gets into your boots and settles on your headgear. After just an hour of work, the mower turns out to be “all covered with greenery, absolutely all”! You have to spend a lot of time on subsequent “sanitation”.
The reason is that trimmers have an excessively small guard over the rotating line. In mine, for example, the shield occupies only a sector, which on the watch dial corresponds to the numbers from 4 to 8, which is clearly not enough.
To eliminate this drawback, I cut off the plastic shield in my trimmer and left only the third (central) part attached to the rod. Then I made an enlarged shield from an aluminum sheet 0.2 mm thick and 250x250 mm in size, which I attached with two screws from above to the remaining part of the former shield (see figure).
As a result, the resulting new shield began to cover the entire semicircle of rotation of the line facing the mower, protecting him from flying greenery. The effect of this modernization was remarkable! Now even boots don’t get dirty above half the tops.
If there is no aluminum sheet, you can use a rubber or linoleum plate. To prevent the edges of such material from drooping, they will have to be reinforced on top along the perimeter with steel wire. In this case, the peripheral parts of the material must be held in a raised state by the wire. The shield material must be attached to the wire precisely in these places, inaccessible to the rotating fishing line.
Anatoly Yarusov, Minsk
TOOLS FOR CRAFTSMAN AND CRAFTSMAN, AND HOUSEHOLD GOODS VERY CHEAP. FREE SHIPPING. WE RECOMMEND - 100% CHECKED, THERE ARE REVIEWS.
Below are other entries on the topic “How to do it yourself - for a homeowner!”
How to put a knife on a trimmer
With the arrival of summer, many homeowners are worried about the question of how to put a knife on a trimmer. More pressing questions are why and when to purposefully replace the fishing line on a lawn mower with a stronger cutting element. In our article we will try to sort it all out and give useful tips summer residents
Why you need to put a knife on a trimmer
A trimmer with a knife installed on it is more convenient total use for more comfortable mowing of tall and coarse grass in the countryside. In such cases, the line on the brush cutter does not control. Installing a knife on a Chinese trimmer: how to remove and install old chain. The narrow one breaks very quickly. Discussion of the stihl fs 55 trimmer on the casing below, I don’t understand how to install the bobbin. The introduction of a thick 2.3 mm cord or homemade rods with cables forces the vegetation to wind onto the spool. This increases the load on the engine. As a result, the piston group and other moving parts of the unit wear out very quickly.
If you mow weeds with an electronic trimmer without a knife, using fishing line alone, even a thick one with a shaped cross-section, the problem will not be solved. There is always a risk of overheating the electric motor and damaging the flexible shaft. And it's all about the high torque of the electronic motor. The grass wound around the spindle creates strong resistance to the shaft, reminiscent of a speedometer cable, which cannot withstand it and gets twisted.
In order to protect equipment from early wear and tear, manufacturers have provided the possibility of installing special knives on trimmers. The design and shape of the existing cutting parts allows you to easily handle not only coarsened and overgrown grass, but also successfully fight with young bushes.
What knives to put on electric and lawn mowers
Before you take a knife and put it on a lawn mower, let’s find out what they are and in what cases they are used. Now manufacturers offer consumers a huge number of types of these Supplies. In general all cutting tool, intended for mowing grass, can be systematized:
- By the type of material from which it is made;
- According to the shape of its cutting blades.
The main material for the production of trimmer knives can be plastic or metal. The implementation of such consumable parts almost entirely depends on two characteristics:
Read also
For safety reasons, manufacturers do not recommend using iron blades on electronic trimmers. In fact, all lawn mowers powered by an electronic network and battery equipped with plastic blades. How to properly place knives on a trimmer (motor mower). Depending on the manufacturer, they may be one-piece design disk-shaped, with several blades, or in the form of a special mowing head that provides for the installation of removable plastic blades.
Assembling the protective cover of the Huter trimmer
Manufacturing of protective casing For trimmer.
Trimmer protective cover
Motokosa. How to replace a damaged shield. The shield got damaged within a few days. Maybe I'm unlucky. In high
A straight shaft for a gasoline trimmer and a curved one for an electric trimmer
Place a metal knife on electric trimmer its design features do not allow it.
- The curved rod of the unit reduces the distance from its working part to the mower’s feet. If the blades collide with a stone or other hard object, the scythe is thrown towards the feet.
- The high torque that we mentioned above, in the event of a collision between a metal blade and a hard object, transfers a large load to the flexible shaft of the trimmer and its motor. What causes their premature failure.
- The handle of an electric scythe most often does not have a limiting bar that acts as a stop. But you should not rely only on them, since this is not what the casing of the cutting trimmer is designed for. This does not exclude leg injury.
It is these features that allow it to be used on trimmers with electric motors exclusively plastic knives. When colliding with an obstacle, the blades are destroyed, thereby protecting the mower’s legs from possible injury.
Plastic knives work well with overgrown and dry grass. They can mow down nettles and burdock stems.
The use of metal knives only on gasoline trimmers is also due to design features.
- The straight design of the boom increases the distance to the legs, which ensures complete safety for the mower.
- Comfortable U-shaped and J-shaped handles allow you to hold the tool firmly. The D-shaped handles of the lawn mowers are equipped with a limiter that rests against the leg of the mower, which does not allow the head to be allowed to approach the legs when the cutting disc encounters a solid obstacle.
- Clutch gasoline engine allows you to smoothly gain speed up to optimal level. And when the blade collides with a hard surface, it is able to absorb part of the impact.
Read also
Thus, petrol trimmers With a metal blade installed, it is best used on large areas. They will successfully cope not only with tall, coarse grass, weeds, burdocks and nettles, but also shrubs, as well as young trees.
The shape of the blades of the disc placed on trimmer does not in any way affect the quality of the work performed. Speed does not depend on them either. Triangular, trapezoidal, rectangular shapes This is all a marketing ploy by the manufacturers.
If you plan to make hay, it is best to put knives with big amount blades. Look for discs with eight teeth or discs with four large blades and four additional ones. Two and three bladed knives will chop up the grass greatly.
How to properly place a knife on a trimmer
Put cutting a knife onto a trimmer is not that difficult. The manufacturer equips its tools with a special pin that allows you to lock the gearbox and a key with which you can unscrew the spool with fishing line. The most important thing to observe when changing cutting elements safety precautions and sequence of assembly and disassembly.
The algorithm for installing the knife on the trimmer is as follows:
- We remove the protective casing;
- We block the drive. To do this, you need to align two holes - in the shaft hub and in the gearbox cup. After aligning them, insert a pin into the holes;
- Unscrew the spool with fishing line clockwise from the hub or fastening nut holding the boot (if the trimmer has not yet been used);
- Next we install cutting knife, so that the slots on the hub washer coincide with the recesses in the hole of the cutting disc;
- Install the boot;
- Tighten the fastening nut (counterclockwise) while holding the locking pin;
- Tighten it using a tubular wrench;
- We return the protective casing to its place.
All owners of personal plots are faced with the problem of mowing grass, which grows literally before our eyes, and during the season it is necessary to improve their plot several times. The usual hand scythe has long been replaced by gas trimmers and electric trimmers. But the price for them does not decrease and is quite significant for many owners of dachas and private houses. Craftsmen nevertheless found a way out of this situation and learned to make trimmers with their own hands literally from improvised means, using gas and electric tools not intended for these purposes.
Most often, a homemade electric trimmer is made on the basis an ordinary grinder which is available to everyone home handyman. This tool is almost ideal for converting into a trimmer. It has more power than store-bought machines and larger number revolutions per minute. In addition, the standard nut used in the grinder to secure the discs already has holes through which it is easy to insert a fishing line (cord).
So, there are many options for what to make a barbell (holder) from. The simplest one is longer than for a shovel, wooden holder. By the end of it under the right angle The grinder is attached using regular tape. The fishing line is inserted into the 2 holes of the nut, after which it is tightened. Thus, in a few minutes you get a trimmer with which you can mow the grass without any problems.
For operational safety homemade apparatus, you can improve it by making a protective casing (how to do this will be discussed later).
For advanced masters with welding machine, we can recommend a more advanced design for securing the angle grinder and the protective casing. It is made made of aluminum tube(serves as a holder) and metal square profile. Looking at the figure below, you can understand the principle of making the holder.
The grinder is secured to the holder with bolts inserted into the holes that are intended for attaching the handle to the device.
The following photo shows what this design looks like from below.
By the way, you can also screw the holder (bar) to the holes for attaching the handle when you want to make a simple trimmer that is easy to assemble and just as easy to disassemble if you need to use the grinder for its intended purpose.
To make it more convenient to hold the trimmer in your hands while working, and it does not rotate around the axis of the rod, you can attach it to side handle made from bent pipe.
From a vacuum cleaner
A trimmer from a vacuum cleaner engine is made according to the same principle as from an angle grinder. The motor must be mounted on a rod, and either knives or a plastic or metal disk must be attached to the motor shaft, into which the fishing line must be inserted. The top of the cutting tool is covered with a protective casing.
To prevent dust and small particles of mowed grass from getting into the motor removed from the vacuum cleaner, it can also be hidden in a plastic casing made from sewer pipe , as shown in the following photo.
Since the motor in the vacuum cleaner is high-speed, it needs provide cooling. Therefore, under the washer into which the fishing line is inserted, it is recommended to insert homemade disk with slotted and curved blades so that it acts as a fan that creates a vacuum. It is required so that air is sucked through the hose from above and cools the engine.
In order to lighten the load on the hands of the mower operator, the unit can be install on a platform with wheels. In this case, you will get something similar to a lawn mower.
To secure the fishing line, you can also use either a pulley with a suitable mounting hole or a plastic wheel from a cart.
From a drill
The simplest mower is made in a matter of minutes from a drill or screwdriver. But first you must make a knife from sharpened metal plate with a hole drilled in the center. A bolt is inserted into this hole and tightened with a nut.
Since a drill with this attachment does not have a protective casing, such a tool is quite dangerous for the user. To protect yourself, you can place the drill, like a grinder (discussed above), on a shovel handle or on an aluminum pipe.
Also, to protect the user of the mower from knives, a casing can be attached to the drill (attached to a plastic pipe and placed on the body of the device).
The drill is attached to the rod using clamps.
From a chainsaw
Many different attachments have already been invented for chainsaws that expand the capabilities of this unit, for example, a cultivator, a drill, a boat motor, and also a scythe attachment. You can see what it looks like in this video. If you want to make a trimmer out of a chainsaw, the maximum you can do is lawn mower on wheels, since the engine of the unit is quite heavy, and it will not be possible to apply the above-described options for manufacturing trimmers (with a lower drive location) to it.
Therefore, the trolley is made first. It can be welded from a 25x25 mm corner. The frame dimensions should be 500x600 mm. The wheels are attached to the corners of the frame.
When installing the trolley handle, make sure that it does not block the winder (starter).
The gasoline engine is installed (screwed through the holes to secure the tire) onto the frame so that the gearbox is rotated 90 degrees and the shaft is at the bottom.
Now all that remains is to attach it to the unit shaft cutting tool. This is done as follows.
- It is necessary to weld a small piece of pipe, 80 mm long and 50 mm in diameter, to the “star” of the device. It is better to cut the pipe into lathe so that the ends are perfectly even.
- Next, find a pipe with a slightly larger diameter - equal to 58 mm. It also needs to be cut to a length of 80 mm. Thus, you will receive a telescopic shaft, which is connected using 2 bolts (m6) located opposite each other. The bolts must have locknuts. Below is a diagram of how the trimmer head is made, which is used to secure the cutting tool.
Several holes need to be made in the telescopic pipes so that the height of the knives above the ground can be adjusted.
It is better to make a knife of such a design as in the following figure.
Due to the fact that movable knives are attached to the disk with rivets, they will simply bounce off when they encounter a stone or a dry branch. This will protect the shaft and gearbox from damage that may occur when the tool jams.
The rivets that hold the knives to the disk must be metal.
The diameter of the disk (made from 4 mm sheet steel) should be 180 mm. The knives are made from strips 30 mm wide and 120 mm long, cut with a grinder from a hacksaw blade for wood.
DIY trimmer knife
If you need to mow plants with thick or tough stems, then ordinary fishing line will not cope with this task. Therefore, you cannot do without a special metal knife. Trimmer knives can be bought at a specialized store, or you can make your own, for example, from an old circular saw blade(no soldering). The knife is made as follows.
Homemade protective casing
If you are making a homemade mower, then you will definitely need a protective cover. It will protect your eyes, body and legs from injury from small pebbles and knife fragments if they break.
A casing for the trimmer can be made made of aluminum sheet or thin sheet metal.
In this way, you can make and install a protective cover on a trimmer purchased in a store if the shield has cracked for some reason. The shields in factory devices are made of plastic and often break if you unsuccessfully hit the trimmer head on the ground to lengthen the fishing line.
Trimmer belt
For more comfortable work with the trimmer, if you intend to process large area overgrown with grass, it is advisable to use a special belt. This device relieves fatigue from the hands and back of the mower operator and greatly facilitates the process when compared with the same work, but without a belt.
There are belts shoulder and backpack. The shoulder strap is the most simple device and consists of a loop with two or one latch (carabiner), with which it is attached to the mowing unit. The second carabiner is usually attached plastic plate, protecting the operator’s side from pressure from the trimmer bar.
The shoulder strap is usually used with lightweight trimmers weighing 3-4 kg. For heavier units it is more convenient to use a backpack belt.
A trimmer belt can be easily ordered online or purchased at a specialized store that sells these devices and their accessories.
The price of backpack belts starts from 250 rubles and above.
If there is a desire to make it with your own hands, then any housewife, looking at this device, can easily sew it from improvised materials (old belts and belts). You may have to buy buckles and carabiners. But we still recommend buying a ready-made backpack suspension and not wasting time and money on making a device of worse quality than the ready-made one.
