Compressor for inflating PVC boats. Adapter for a car pump for inflating a boat. Device Specifications

Having a watercraft not only gives you freedom of movement, but also allows you to create comfortable conditions for quality fishing. Today, the fishing market represents huge selection swimming equipment, but the most popular are boats made of polyvinyl chloride (PVC).

Water vehicles made of PVC material have good performance characteristics: high strength, lightness, ease of use, and high stability on water.

To get the boat into working condition, you need to fill it with air and inflate it. As an aid, manufacturers provided special devices - pumps. Among the variety of devices, electric pumps for PVC boats have proven themselves well.

Contents

Advantages and disadvantages of electric pumps

TO positive qualities special devices operating from an electrical power source include:

Speed. Unlike mechanical pumps, electrical devices make it possible to get a two-seater watercraft ready in just 10 - 15 minutes.
Practicality. Using the device, you can not only fill boat cylinders with air, but also inflate car tires, air mattresses and other rubber products.
Does not require physical effort, just connect the valves and the device is ready for use.
Availability of pressure gauge and reverse, which allows you to control the air density and not release it back.
The ability of reverse to produce a reverse cycle.
Availability of built-in adapter. The electric motor can be powered from the mains, saving battery energy.

Negative points include:

Electrical power supply requirements. As a rule, the requirements are for a car or stationary battery with sufficient energy charge.
The cost of an electrical appliance.

Given the large range of models, purchase a quality device at optimal price is quite real.

Types of pumps

Electrical units for inflatable boats made of PVC material are classified as follows, according to the pressure provided:

Low type, where in a relatively short period of time the PVC boat is inflated with air, but in most cases such pressure is not enough to bring the vessel into working condition. Additionally, foot pumps are used.
Medium and high type. Electrical devices that provide medium and high pressure are capable of inflating the boat as quickly and efficiently as possible without the use of aids. Another advantage of this solution is the fully automated process of filling the watercraft’s cylinders; there is no need for a person to be constantly present and control the device. The main thing is to set up the unit to pump the required pressure and connect it to a power source.

Electric pumps for water products made of PVC material can be of two types, depending on the type of power source:

Mains powered, which frees the owner from maintaining control over the battery charge level. However, using the pump requires a power source;
Battery operated. There are external (removable) and internal batteries. Removable models include a spare battery. There are devices on the market for inflating inflatable watercraft that run on a car battery, which is very convenient.

Pump selection

When choosing a product with electric drives, you should pay attention to the following parameters:

Case material. Pumps are produced in a plastic casing, but the internal metal filling has priority.
The presence of two cameras. Electrical devices high pressure are equipped with two chambers, since their design contains a diaphragm and piston mechanism.
Pressure regulator (PR). The presence of a taxiway makes it possible to prevent pumping of cylinders and maintain the integrity of the walls of the craft. Depending on the settings of the pressure regulator, the compress stops its operation after reaching a certain point, without the participation of the owner.
Electrical appliance performance. The best option reliable device - model up to 450 mbar and performance up to 500 l/min.
The presence of reverse and check valve , which will significantly simplify the pumping of air when inflating the boat, and releasing it from the compartments when assembling the vessel.
Power supply. It is effective to purchase models with the ability to be powered from a network or mobile source.

Conclusion: use aggregates low pressure it is not advisable to pump up water efficiently vehicle from PVC material will not work. A poorly inflated water supply poses a danger to everyone on board the vessel.

Pump rating

To choose a high-quality electric pump for PVC boats, it is recommended to familiarize yourself with the most popular models today:

This is a standard small-sized device with a removable 12 V battery, with a capacity of 150 l/min. The inflation time for an inflatable boat 3.5 m long is 20 minutes. The advantage of the pump is the built-in pressure sensor. Cons: high noise level, high the cost of the device is 4,000 rubles.

The high-pressure model is distinguished by sufficient productivity of 1000 l/min and silent operation. The compressor is capable of filling the compartments of a 4-meter watercraft in 4 minutes. The unit can receive power both from the electrical network and from an external battery. The device has reverse and RD. The price is justified by the quality - 10,000 rubles.

This is a standard two-section model, equipped with a pressure regulator, removable battery, and reverse. Advantages of the electric pump: low weight (1.5 kg), special storage case. The fairly good performance of the device allows you to pump up a watercraft with a length of 3.8 m in 4 minutes, and 7.5 m in 15 minutes. The power of 800 mbar is more suitable for large watercraft with an inflatable bottom. The price of the product is 12,000 rubles.

The electric device is ideal for amateur fishing. Its performance characteristics: capacity of 450 l/minute, pressure regulator up to 300 mbar, autonomous operation removable battery is 15 minutes. Price 7500 rub.

The pump from a Chinese manufacturer adequately copes with the tasks of pumping and releasing air, has a power of 195 W, and a capacity of 750 l/min. Excellent value for money and quality. Model price 4000 rub.

Pump operation

You can extend the operational life of your boat device by observing the following rules:

The device must be turned on after connecting to the boat valve and while the car engine is running. This setting will prevent uneven distribution air inside the compartments.
A special device for inflating the boat must be installed exclusively on a flat surface, and be protected from exposure to ultraviolet radiation.
During transportation and at the time of use You should treat the device body with care.
The compressor must be stored in pure form, avoiding kinks in the hose. You should know that the pump body is afraid low temperatures, there is a high probability of damage to the plastic.
To protect the unit from mechanical damage During transportation and storage, it is recommended to use a special case or bag.
Periodically it is necessary to inspect the device and clean it of various contaminants. Considering the specific nature of fishing, there is a high probability of moisture getting on the device, it is recommended to thoroughly dry the compressor.

It is recommended to purchase an electric air blower from trusted manufacturers and specialized retail outlets, where you can get a warranty for the device.
It is necessary to select a boat pump according to the size of the boat.
It is recommended to pay special attention to the technical characteristics of the device (power, performance, etc.).
Follow the rules for operating and storing the device.

Adapter for a car pump for inflating a boat and other things.

It’s a great idea to replace an expensive electric pump for boats with a car compressor, which most people always have in their cars. There is no longer a need to carry two pumps, you just need an adapter adapter for the pump. One side fits most PVC boat valves, the other side is for the compressor.

Our online store site will help you choose everything you need from accessories for your PVC inflatable boat

0 reviews for the product Adapter for a car pump for inflating a boat

Delivery

Dear buyer!
Our online store Tocamp's delivery service operates seven days a week. And we are glad that you chose our store. We will deliver the goods within 1-3 business days from the moment the order is placed. More detailed information, our managers will be happy to provide you with information about the delivery time.

The minimum order amount is 500 rubles.

Delivery in Moscow

The cost of delivery in Moscow within the Moscow Ring Road is 350 rubles.

When ordering an amount over 10,000 rubles and weighing less than 10 kilograms, delivery will be free, within the Moscow Ring Road

If the order value is less than 1000 rubles, the delivery cost is 500 rubles.

Delivery across Russia

If you need to deliver goods to other cities in Russia, then there are several options.

1. You place an order, We confirm the availability of the product you have chosen, you make an advance payment from 20% to 100% of the order value, using a Sberbank BLITZ transfer, transfer to our Sberbank card or another agreed method and we send the product you have chosen after receipt Money Russian Post or EMS by mail Russia. Upon receipt of your order, you will only have to pay the cost of postage, which you can calculate on the Russian Post website.
Our company guarantees that after receiving money for postage and the ordered product, we will send it to you within 1-3 days.
Our company guarantees that all ordered goods will be properly packaged to ensure their integrity and safety. If we are unable to send you the ordered product, we undertake to send you the money back as soon as possible.

Oversized parcels are sent only after prepayment!

You can track your parcel on the Russian Post website.

2. Delivery of goods by the transport company is subject to 100% prepayment.

Delivery to the Russian Post and to the transport company costs 200 rubles.

Delivery to the Moscow region

Delivery costs are calculated according to the scheme 350 rub.+30 rub. per kilometer.

Remember that the time spent coming to us can be much more expensive than the cost of delivery.

Pickup available.For pickup you must be sure to place an order through the website, where you indicate the required product, after which our manager will contact you and specify the pickup time. The pickup point is located at: Moscow, Pyatnitskoe highway 24 from 1

Purchasing an inflatable boat requires purchasing a high-performance pump. This is due to the fact that it takes a lot of time to inflate it with the “frog” pump that is included with the boat. As a rule, preference is given to an electric pump that operates from battery car. Despite this, not every PVC boat owner is ready to buy an expensive item.

The choice of pump depends on various factors that can influence the selection process. First you need to decide on the purpose of the pump and its price. Before purchasing, it would be a good idea to pay attention to the following characteristics of the model:

Acceptability of operation from a battery or car cigarette lighter. Usually, centrifugal pumps operate from the car's on-board 12V network. Designs with higher performance are connected to both the battery and the cigarette lighter. At the same time, there are models that operate from a 220V network.
Boats with a length of up to 4 m require an electric pump with a capacity of 300-400 liters per minute. Boats with a length of more than 4 meters require a pump with a capacity of up to 1000 liters per minute. The pump should provide a force of 300-400 mBar, so that you do not have to pump up the watercraft with a manual pump, such as a “frog”.
The presence of a check valve for pumping air out of the cylinders. This function makes it possible to perfectly pump out air from the boat, which makes it possible to fold the boat more tightly for transportation.
The presence of a built-in pressure sensor, which allows the pump to operate in autonomous mode. At the same time, there is no need to control air pressure.
Availability of built-in battery.

5 best electric pumps for pvc boats

It features a built-in power regulator, which expands its functionality. Using a pump, it is possible to inflate not only boats, but also other structures. In eight minutes he can pump up a four-meter boat to optimal pressure.

The user can independently choose operating pressure. After inflating the structure, the device itself is able to turn off, which will protect, for example, a boat from overpressure. With its help, it is possible not only to pump up, but also to deflate air. The pump kit includes connectors for various designs valves, which allows you to inflate various designs.

Specifications devices:

Supply voltage – 12 V.
Current consumption - up to 9 A.
Capacity – 150 l/min.
Working pressure - 300 mbar.
The weight of the structure is 1100g.

It is designed to obtain optimal pressure in air cylinders.

The package includes:

Hose for connecting to the pump.
Electrical cable with alligator clips.
Set of adapters for various valve designs.
The fitting that connects air hose with compressor.
Built-in pressure control regulator.
Carrying bag included required quantity compartments

To pump up the structure you need:

Connect the air hose to the compressor and the object being inflated.
Connect the electric pump to the battery using alligator clips, observing the polarity.
Turn on the device by pressing the “ON” button.
Set the required pressure on the sensor.
After completing all preparatory operations, press the “START” button.

To pump air out of the boat, switch the air supply hose to another pipe labeled “IN”. All subsequent steps are the same as when inflating the boat. The body of the device is not protected from moisture, therefore, when near a body of water, you need to be careful not to let moisture get on the device.

Technical characteristics of the electric pump:

The maximum created pressure is 250 mbar.
Capacity – 1000 l.
Current consumption – 45-60 A.
Supply voltage – 12 V.
Weight – 3.5 kg.

The pump model is designed for inflating large inflatable PVC boats.

The package includes:

Air supply tube
Cable with alligator clips
Valve adapter kit
Pressure control indicator built into the housing
Keys to turn the pump on and off.
Carrying bag.

The design consists of two separate blocks. The operation of the device begins with the launch of the first module. When the first module reaches maximum operating pressure, the second, more powerful module comes into operation. When the second unit is turned on, the pump becomes noisier.

If the device does not switch, you should pay attention to whether the battery is fully charged and, if necessary, charge it. Although other reasons are possible.

The boat is inflated as a result of the following steps:

Connect the air connection accordingly.
Connect the pump to a power source.
Connect the pipe to the boat using the appropriate adapter.
The pressure regulator is set to the desired position, after which the “ON” button is pressed.

To pump air out of a boat:

It is necessary to switch the air hose to the air pumping pipe.
Pumping is not carried out autonomously, so you will have to control this process.

Main technical characteristics:

Maximum operating pressure – 800 mbar.
Supply voltage – 12 V.
Current consumption – 15-20 A.
The device weighs 1.9 kg.

This pump is suitable for inflating watercraft with a working pressure of cylinders of no more than 300 mbar. This is always noted in the boat's passport. The electric pump BRAVO BST 12 is designed on the basis of a two-stage compressor, which allows you to inflate other inflatable structures.

The device kit includes:

An electrical cable up to 3 meters long, which can be connected to both the battery and the cigarette lighter, as well as a set of connectors for various valve designs.
Built-in pressure regulator.
Air hose.

Device characteristics:

Supply voltage – 12 V.
Current consumption – 15 A.
Maximum pressure – 300 mbar.
Capacity – 500 l/min.
Device weight – 1.5 kg.

Using this model, you can quickly both inflate the boat and pump out air from the cylinders. Capable of operating both from a 220 V network and from the vehicle’s on-board network with a voltage of 12 V.

The kit includes:

Pump.
Tube for pumping air with adapters.
Converter 220/12 V, as well as a connector for connecting to the cigarette lighter.
Warranty sheet.

Main characteristics of the model:

Manufacturer – Intex (China).
Power supply – 220/12 V.
Capacity – 600 l/min.
Maximum pressure – 800 mbar.
Weight – 3.5 kg.
Dimensions – 260/160/110.

In order for the pump to please its owner with reliable and confident operation, the following recommendations should be followed:

Turn on the pump only after thoroughly checking all connections for reliability.
Operate only with a fully charged battery.
The device must be installed on the same plane as the inflated object.
Do not leave the device under direct sun rays or in the cold.
Do not allow water to enter and avoid mechanical damage to the housing.
Avoid kinking the hose during operation.
It is not recommended to work without a break for 20 minutes or more.
Transport only in the case that comes with the device.

Depending on the output pressure, electric pumps are divided into 3 categories:

Low pressure pumps (40 mbar). Suitable for pumping up small-sized boats. After preliminary pumping, the boat is inflated with a mechanical pump (frog).
Medium pressure pumps (500 mbar). With their help, you can pump air into boats up to 4 meters long inclusive, without additional pumping.
High pressure pumps (800 mbar). Used for inflating large inflatable watercraft, as well as for inflating boats with an Air deck bottom.

Why do you need a high pressure pump (up to 800-1000 mbar)?

As mentioned above, such a pump is used to pump larger devices. At the same time, it has an impressive price. It is better to choose a pump depending on the type of boat and its characteristics.

The advantage of pumps is that a medium-sized boat can be pumped up in 10-15 minutes without much effort.

In addition to everything said above:

The presence of a pressure indicator allows you to keep control over the process of its operation.
The presence of a reverse function makes it possible not only to quickly and efficiently inflate the device, but also to quickly and efficiently pump out air from it.
Models with a 220/12 V power supply allow you to save the battery and use it when it is not possible to connect to a 220 V network.

Along with the advantages, the disadvantages should also be noted, which include:

The need for a power source.
The device is expensive.

For those who have not yet purchased an electric pump, it will be interesting to know:

It is recommended to purchase such devices only from well-known and trusted manufacturers.
The pump is selected based on the volume of your watercraft.
It’s not bad if the design is equipped with a turbine-piston supercharger.

In other words, pump selection is preceded by various factors, which, one way or another, influence this process. The main factor that can become decisive is the financial factor. The more opportunities an angler has in terms of availability of funds, the better quality model can be purchased.

Moreover, the dependence on capabilities can be traced by the presence of a PVC boat, and most importantly, its size. Accordingly, a pump will be purchased. Although many fishermen still use a “frog” and only dream of an electric pump.

The boat pump is very useful device, greatly facilitating the process of inflating the product. In some cases, people give preference to models general purpose or pumps for cars. But there are a number of advantages to using a device assembled specifically for a boat.

Specialized equipment always has a number of advantages over conventional equipment, be it an electric pump for a boat or something else. The main criterion is device performance. The compressor power is calculated taking into account the parameters of the rubber product, so there should be no problems during operation.

Many people wonder why buy a specialized device if you can inflate a PVC boat with a car compressor with your own hands? Of course, it is possible to pump up the boat, but a number of difficulties will arise. A car pump is not designed to pump such volumes of air, so it will take a very long time to completely fill a PVC product with air. Not everyone is ready to spend so much time waiting, sitting on the river bank. In addition, in most cases, an adapter may be required to inflate the boat with a car compressor.

Types of pumps

PVC boat pumps are divided into two categories. Models capable of creating low pressure, as well as medium and high pressure.

Low pressure type provides relatively fast air pumping, but this pressure is maintained for a relatively short time, and it is not enough to bring the boat into operational condition. Most often, for pumping it is necessary to use a foot pump.
Medium and high pressure. Models that pump medium and high pressure are capable of inflating the boat as quickly as possible. They do not require additional devices for paging. Another significant advantage is the complete autonomy of the process without human intervention. Just connect the device to a power outlet and turn on the button.

Pumps are also divided into hand, foot and electric. The latter are capable of providing high pressure for maximum short term. Basically, pumps are selected depending on the size of the boat. Every PVC manufacturer products equips its model with the most simple pump"frog" type. But to pump up a boat with such a device, you will have to put in a lot of effort. This is why many fishermen prefer to initially purchase a more productive model.

Foot and hand pumps

Everything is relatively simple here. If the leg pumping method is the most preferable, then all that remains is to choose the model suitable for the characteristics of the existing boat.

For a PVC boat no more than three meters, having a chamber volume of 5 liters and a pressure of 300 mbar.
For a boat with a length of three to four meters, chamber volume up to 6.5 liters and pressure up to 400 mbar.
For any PVC boat whose length is four meters or more, the permissible volume is 6.5 liters and the pressure is 500 mBar.

Manual pumps for inflatable boats are usually distinguished only according to two main parameters.

For short-length boats (up to 4 meters), double-acting, with a cylinder volume of 1.5 liters. The pressure is 500 mbar and the cylinder length is 410 mm.
For all other boats with a length of more than 4 meters, having a double action and a volume of 2.5 liters. Pressure in in this case is 600 mbar, the cylinder has a length of 510 mm.

Hand pump

The convenience of using hand and foot pumps for inflating a boat is rather questionable, but they do not require power supply, and they can be used in any, even the most remote places. In addition, they are lightweight and compact.

Electric pumps

Electric boat pump is the most convenient and functional solution. To use it, you only need a power source. There may be two options here.

Also, electric pumps are divided according to the principle of operation into centrifugal and piston. The first of them provide pressure levels up to 200 mbar, and models with piston principle work – up to 800 mbar.

There are a few simple rules, following which, it will be possible to purchase a model that will suit your existing PVC boat.

It is necessary to select models with highest degree of housing protection. This is very important if the device will be used in extreme conditions.
When choosing a model, you must be guided by reasonable principles; you should not choose something that is obviously cheaper or more expensive. Often, the question depends not on the price, but on the parameters of the existing PVC product. In the case of an electric pump, it is necessary to take into account that its performance strictly corresponds to the parameters of the boat.
You should not purchase “no-name” models that do not even have the manufacturer’s name on them, but only an index. The best thing give preference famous brands , well proven in the market.
It is important that you diaphragm pump dominated metal elements - this will significantly extend its service life.
A significant advantage will be that the pump has pressure sensor, as well as regulator.

Review of the best boat pump models

Here are 5 models that deserve positive reviews from many fishing enthusiasts. The mini-rating has both manual and electric models(mains and battery) - everyone can choose a product to their liking.

The fifth place is occupied hand pump from the famous manufacturer "Intex". This model is intended primarily for those who prefer to travel light. Using such a pump is simple and convenient, and most importantly, after prolonged pumping, your palms do not hurt at all. The case is made in black, without a choice. Material of manufacture strong and durable plastic. For hand pumps The last point is not a minus, because they lack an automated supercharger. On the contrary, the plastic case is much lighter and, therefore, more convenient to transport.

The device does an excellent job of inflating any PVC products. Comes with set of various nipples and nozzles for connection to various objects. The cost of the device is 528 rubles. In addition to a set of nozzles, the pump is supplied with a durable corrugated hose.

inexpensive;
easy to use;
reliable;
takes up little space;
trusted manufacturer;
various attachments included;
stylish appearance.

low productivity;
You won’t be able to pump up a large boat without a low-pressure supercharger;
short corrugated hose included.

4.Bestway

When looking for which pump to buy, you should pay attention to the model from Bestway. This is a wonderful device from a Chinese brand. The company has been present on the market for quite some time and has positive reviews about its products. The device is offered in large retail chains at a price of 1,299 rubles. A very competitive price for an electric pump, considering competing models. Distinctive feature of this device is work from 220 V network. You just need to plug it into a power outlet and wait for the result. The pump can handle any PVC product: boat, swimming pool, mattress. The device is small in size and easy to transport.

Electric pump Bestway 62097

Important! The delivery set includes only the unit itself and the hose. A set of adapters can be purchased separately.

A great solution for those who have big boat, requiring a powerful compressor at hand. The weight of the model is only 441 grams. A pump proven by time and users.

high performance;
long warranty period;
famous brand;
reliability;
strong body;
small size;
convenient to transport;
easy.

works only from the network;
no adapters included;
noisy.

3. STERMAY

The top three opens famous manufacturer"Stermay." This PVC boat pump is widely popular among fishermen. First of all, the model is purchased for good combination cost and performance characteristics. You can buy the model for only 4940 rubles. The main advantage of this unit is battery operation. In the kit you can find special tweezers (crocodiles) with which the device is connected to the battery. This is very convenient in conditions where there is nowhere to connect to an outlet.

STERMAY high pressure electric pump with crocodiles, 12 V

The device is capable of pumping up to 230 liters per minute. The maximum operating pressure is 1.37 Bar. Continuous operation time is no more than 15 minutes.

Advice! During the specified period, the device can drain the battery, so you should take care of a replacement one.

Device made of plastic and operates on a voltage of 12 V. The number of injection intensity levels is two. Very good device, which can be used far from civilization. Indispensable for everyone who is interested in fishing on the water.

high performance;
battery operation;
optimal pressure in the system;
two stages of injection;
famous manufacturer;
15 minutes of continuous operation;
voltage is 12 V.

no pressure sensor;
plastic case;
strong vibration and hum.

2.GP-80

One of the most popular boat pumps today. The GP-80 is rarely seen for sale simply because it is purchased so frequently. The average cost is 6362 rubles. This is a battery supercharger, which comes with special “crocodiles” for connecting to the “plus” and “minus” of the battery. Also comes with pump durable corrugated hose and as many as eight attachments for different types boat nipples. The weight of the device is 3 kg. The model is made of impact-resistant plastic in bright yellow color. A feature of the device, like the model above, is battery operation. This makes it possible to use outdoors.

reliability;
high performance;
strong body;
small dimensions;
battery operation;
operating voltage 12 V;
light weight.

drains the battery quickly;
loud noise during operation;
there is no sensor.

The best pump of today's top 5, model Bravo bp12, optimal choice in the middle price category. The cost of the device is only 4195 rubles. This is a durable and reliable unit capable of create pressure up to 1000 mbar. This indicator is a decisive criterion, because for most modern boats this pressure is sufficient in abundance. What is important, the device is equipped air pumping function. The device weighs only 1.7 kg, making it very convenient to take with you on a boat. Thanks to the “crocodiles” included in the kit, the pump can be powered from almost any 12 V battery. The maximum current consumption is 20A, which is quite standard for most electric pumps.

pumps up the boat in 12-15 minutes;
The kit includes an air hose;
detailed operating instructions;
light weight;
convenient dimensions;
very productive;
Italian production.

The battery runs out quickly;
hum when working;
cost of the device.

Conclusion

Choosing a pump for a PVC boat can be simple, but for this you need to take into account the parameters and criteria described above. To purchase the required model, you should be well aware of the characteristics of the boat itself, as well as familiarize yourself with the nuances of operating the selected type of pump.

Summer... I really want to rush somewhere into nature and enjoy open air by the pond, barbecue, sunbathe, play volleyball or just go fishing with friends. If there were cars, there would be a desire, and there would always be a place to relax. But, one way or another, today it is difficult to imagine outdoor recreation without air mattress(a very popular product for beach holiday), an inflatable boat, an inflatable pool for children, etc. All this should be in the arsenal of a modern summer resident or tourist.

An inflatable boat, for example, today is perhaps the best watercraft for those who love fishing. However, such a boat needs to be: a) assembled and b) inflated. Alas, if an inflatable boat has low pressure, then it naturally loses its qualities. Therefore, you should always have a booster pump at hand. As a rule, pumps are included with inflatable products, but they are very simple; inflating a boat or mattress with them will not be easy and will take a lot of time. There are, of course, a large number of various pumps: manual, foot, electric. However, choosing a pump that is durable, convenient, and also able to quickly inflate a boat of any size is a non-trivial task. Or maybe there is a way to inflate a boat without buying a pump for it at all? It turns out there is - you can use a car compressor!

Agree, it is difficult to imagine the owner of an inflatable boat without a car. So why not use this already powerful enough pump? Of course, this device is designed for swapping car tires- it won’t be possible to simply adapt it to a boat (at least for purely geometric reasons). You need some kind of adapter, adapter. You can, of course, try to make it yourself (there are such craftsmen), but it is still more correct when you have (and successfully use) a special nozzle for pumping up inflatable products. Not only boats, but also, of course, any other inflatable products.

The BERKUT brand, known for its legendary automotive compressors, has introduced a unique adapter under the article number VT-300. This device is based on Venturi tube technology, named after the Italian scientist. The principle of operation is simple - the pressure of the air flow from the compressor decreases due to the passage of a narrowed section of the pipe. And productivity (volume of supplied air) is increased due to a special associated air duct. The BERKUT VT-300 adapter is connected to the compressor hose using threaded connection and can be used together with nozzles designed for inflating and, of course, deflating air from inflatable boats, mattresses, swimming pools and all other products that require a fairly large volume of air.

BERKUT brand adapter easy to use. First you need to select a nozzle (one of three included) for pumping air, then connect it to the desired input, insert it into the desired product (for example, air valve inflatable boat) and start pumping.

If the inflatable product, using the VT-300 nozzle, is not inflated to the required pressure level, then you can close the air duct (inflation outlet) with your finger in order to increase the air pressure. But keep in mind that holding (clogging) the outlet for a long time with your finger can cause pumping. So you need to take precautions!