Electronic musical instruments, along with a computer, occupy permanent place in the apartments of Russians. Many people know how to play themselves and enjoy playing music in free time. In addition, children are growing up, and the prestige of music education has not yet been canceled. Even if a child does not become a talented musician or composer, the ability to play a keyboard instrument will significantly increase his status. The choice of electric musical synthesizers is large, and you can choose an instrument of any level.

Electronic pianos allow you to position your hands and fingers correctly and at the same time do not disturb your neighbors at all, since you can play with headphones. The big disadvantage of this technique is the separate purchase of a tool stand. These designs are expensive and not very reliable, so many are interested in the question of how make a stand for a synthesizer with your own hands.

There are many options simple designs, which can be made from scrap materials or use those already available in household things. Very simple stand can be made into a home synthesizer from an ordinary ironing board. In fact, this is an almost ready-made folding stand. The material with which it is covered can be cut off and replaced with another covering.

The board itself is attached to the supports with screws, so it can be removed and a new one cut. If the electric musical instrument is not too heavy, then this design will be quite reliable. The good thing about the design is that no tools are required for its manufacture. DIY synthesizer stand can be made from available materials such as metal pipes or profile. Despite its simplicity, this design is not intended for heavy models; in addition, a lively child can knock it over, so You can make your own digital piano stand from wooden parts . The prefabricated stand will be quite stable. The entire structure is assembled from four parts. These are two sidewalls, a tabletop and an additional horizontal strip between the sidewalls, which provides additional rigidity.

DIY Casio digital piano stand

Typically, a stand for an electric musical instrument costs about 5-6 thousand rubles. This amount does not suit everyone, so DIY Casio digital piano stand can be done without much difficulty. The basis for production is furniture laminated particle board 16 mm thick. Only four parts need to be cut out of it. Their dimensions are determined by the model of the musical instrument and the required height above the floor level. You can cut the boards yourself, but it is better to have them cut to companies that do this. It will cost less, and the quality will be much higher.

To assemble a structure for an electronic piano, you will need a furniture corner, screws, PVC edging and plastic inserts on the lower part of the sides so that the structure does not scratch the floor. The laminated board can be chosen in the desired color.

If you have a tool and experience working with it, then the stand can be made more complex. The design can be made in the form of a table, where the tabletop is raised on brackets. Can be used piston system, or some other. The table stand is made of furniture board thickness 20-22 mm. On the top shelf you can place Acustic systems. Metal legs and mechanics can be purchased at construction market. How to make a stand for a synthesizer with your own hands. The main thing here is to cut the parts correctly. For fastening, furniture fittings and screws are used.

When you have two electric musical instruments, you will have to do two-story structure. To make simple and two-tier stands for electric musical synthesizers, an excellent construction system called “Joker” is used. It is designed for quick assembly of various commercial equipment.

These are stands, showcases, racks and much more. The basis of the system is chrome-plated steel pipes with a diameter of 10, 25 and 32 mm. They can be connected to each other by various couplings, racks and tees. In order to do DIY digital piano stand It is enough to cut the pipes to the required length and use locks to assemble any structure from them. In addition to a hacksaw or grinder, you only need an internal hex key. Placed on the ends of the pipes plastic plugs, and shelves for synthesizers are cut from any material. DIY music stand for synthesizer can be done in a very short time.



🎄🎄🎄 Happy New Year! The work schedule can be found in the "News" section🎄🎄🎄

HOW TO CHOOSE A KEYBOARD STAND

Ergonomic stands provide comfortable support for keyboards. With their help, you can optimally position controllers, synthesizers and other equipment. This practical accessory allows you to select and fix the height that suits a particular performer. Compactness and manufacturability of most modern products eliminates problems with storage and transportation.

Choosing the right support increases the musician's comfort while playing. From our article you will learn about the features of various racks and will be able to better navigate the assortment.

Main types

X-shaped type

One of the popular varieties. Consumers note the following advantages:

Stability, wide rubber pads prevent slipping;

Comparative lightness of products made of steel or aluminum;

Easy to transform and move;

Height adjustment with screw adjuster for playing in a standing or sitting position;

Affordable price, versatility, ability to use in any conditions.

The only limitation with cross-shaped stands is that they are suitable for music equipment weighing up to 55 kg. Roxtone KS016 - best option for light synthesizer and other keyboards.

XX-shaped models

Their distinctive feature- double frame. It provides greater stability, strength, and readiness for high loads. Reinforced metal structures are heavier and more expensive than conventional ones. Thanks to its double legs, the Roxtone KS020 can easily support the weight of a digital piano up to 80 kg. Height is adjustable in the range of 30-100 cm.

Z-shaped version

Original accessories look modern and attractive even in home environment. They will serve as a reliable support for your synthesizer. Some products can be adjusted in width and height; this group includes the OnStage KS7350.

Using the stand, the synthesizer is placed at the desired level. The ergonomic design is equipped with latches with clamps, which allows you to set one of 6 positions (60─96 cm). The width is adjusted by a special screw mechanism. When using a full-size keyboard, the length of the crossbar can be increased to 84 cm.

The OnStage KS7350 is ideal for the stage. Lasting metal carcass Can support keyboards or mixing consoles weighing up to 170 kg. When folded, the accessory is made of aluminum alloy takes up little space. It is convenient to store, move and transport.

Stand-table

Products of this type are usually made of metal. They are characterized by high strength and versatility of use. The table stand does not deform even after prolonged use. frequent use. It is used as a stand for keyboards, controllers, DJ equipment, mixers and more.

A significant advantage is the practical option of adjusting the width and height in a sufficient range. Four supports guarantee maximum reliability and stability. The sliding OnStage KS7150 easily supports large and heavy tools weighing up to 104 kg. The table stand can be installed at a maximum height of 109 cm, and the width can be increased to a meter.

Column or tripod

A two-tier keyboard stand consists of 2 tiers located at different heights. Such design feature allows you to place more than one tool, use necessary equipment. The heavy metal tripod provides reliable support and can withstand high load up to 100 kg and above. The strong elements of the inclined column and the stability of the base inspire confidence; you don’t have to worry about the safety of the equipment.

The two-tier design of the OnStage KS9102 provides the ability to attach a microphone stand, and there is a channel for cable placement. This tripod can support keyboards with a total weight of 110 kg. Accordingly, the load on each level should not exceed 55 kg. The height of their location is independently adjustable, up to 109 cm.

Racks with multiple tiers

Ergonomic multi-tier accessories are indispensable for saving space and compact arrangement of tools and equipment. The two-story professional model Proel SPL152 from the famous Italian brand is popular with many performers. The reinforced design allows you to place additional keys along with the main ones.

For this purpose, second-level racks with a depth of 33 cm are used, with maximum height 97 cm. You can place a music stand, microphone and laptop nearby. Load limit 50 kg.

Wooden racks

Unlike other varieties, models of this type do not fold and are not adjustable. Their parameters remain unchanged. The significant weight of products made from solid wood or chipboard requires stationary placement. At the same time, they have many advantages: strength, reliability and stability.

The CASIO CS-44 stand deserves the trust of musicians. It is perfect for digital pianos and synthesizers CDP-230, 220, 200 and others in this series. The combination of a massive structure with modern equipment looks contrasting and stylish. This option can transform the design of the room into better side. Special design elements are designed for stable fixation of musical equipment.

What to look for when choosing

The main criterion is the conformity of the type, technical characteristics, rack designs for your tools and equipment. Please pay attention to the maximum permissible weight specified in the product passport. If it is exceeded, there is a high risk of the support falling. The consequences can be tragic: breakdown of an expensive musical instrument or equipment.

Height and width adjustment are important options that increase the operator's comfort. Correct location the instrument reduces stress and fatigue, which has a positive effect on the quality of music. If we're talking about about the younger generation, then an adjustable model will definitely be needed. For an adult musician and home use you can limit yourself wooden variety with unchanged parameters.

Are you expected to travel frequently, transport tools and related accessories? Then choose a folding model that takes up little space. Check the tightness of latches, adjusters and fasteners to avoid unpleasant surprises.

The design and appearance of the stand is essential for professional performances in concert halls. It should be as comfortable as possible and look quite presentable. At home, it all depends on personal preference. Some give priority to strength and reliability; design does not of great importance. Others will choose an expensive copy that will become stylish addition interior

Choosing a keyboard stand should not be underestimated. Imagine your feelings when a poorly chosen accessory starts to sway during the game. It's worth taking a closer look different options, carefully study the characteristics and decide what is more suitable in your case: a stable three-tier tripod, a durable XX-shaped model or a lightweight “clamshell” made of aluminum.

Almost any modern keyboard instrument needs a reliable support. allows you to place the tool so that it is on optimal height and was securely fixed. Modern racks are compact structures that are convenient to transport without wasting space and, if necessary, can be installed in a couple of minutes in the desired position.

If you are using a synthesizer, MIDI keyboard, controller or drum machine, it is recommended that you select the appropriate stand. But how to choose it correctly? This article is devoted to this issue.

Types of racks

1. X-shaped. This is the most common and optimal option for all occasions. This stand is quite light, stable, easy to fold, and adjustable in height, which allows you to play the instrument both sitting and standing. The disadvantage is the small weight of the tool, which the stand can support. Such racks, using a screw regulator, can stepwise or continuously change their height, and are made of metal (usually steel or aluminum). The cross-shaped stands at the top and bottom are equipped with wide and dense rubber pads to prevent the tool and the stand itself from slipping.

2. XX-shaped . These racks are a reinforced version of X-shaped racks. They are much more stable due to the double frame, but, accordingly, they are heavier and somewhat more expensive. But they can withstand more weight of the tool. Metal stands are the most budget-friendly and popular type of synthesizer stands.

3. Z-shaped posts - a reliable accessory for a synthesizer, can be used both at home and at a concert. Z-shaped metal structure It looks very stylish and at the same time is quite stable.

The ROLAND KS-18Z stand is a Z-shaped design that can fit practically and elegantly into any interior, has a fairly light, transportable weight and very durable structural parts, can reliably hold even the heaviest types of keyboard instruments and synthesizers, with a full-size keyboard in 88 keys (up to 90 kg). The stand is made of a special heavy-duty aluminum alloy, which gives it maximum a light weight and strength. The design of the stand is a special folding mechanism with strong connection elements with position locks in the form of a screw clamping mechanism. The stand is equipped with convenient height clamps; these are clamps with a screw clamp; there are only two clamps for the left and right side. It is possible to adjust the height of the stand, there are six levels in total (from 607 to 932 mm). To adjust the width, there is a mechanism for adjusting the width of the rack (from 615 to 938 mm), this is a specially adjustable crossbar, with width locks on convenient mechanisms with a screw clamp.

4. Stand-table . This stand is considered the most reliable and versatile, as it can be used not only as a stand for keyboard instruments, but also for other types of equipment - mixers, controllers, etc. It is also made of metal, adjustable in height and width and, thanks to four support points, ensures a secure position for the tool.

5. Column-shaped stand (tripod) , which is needed for especially heavy tools and can withstand a total weight of more than 100 kg, usually has two tiers. On the optional second tier, you can place a tool that is not too heavy (usually no more than 25 kg), whereas with a column stand the weight adds up and usually exceeds a hundredweight.

6. Double and multi-tiered racks allow you to save space and securely place your equipment.

7. Wooden stands . Such racks are usually made of chipboard ( a budget option), or from solid wood, which is significantly more expensive. Although wooden stands look very stylish when combined with a digital piano, they represent stationary option and have a number of disadvantages: heavy weight, impossibility of folding, and therefore compact placement, non-adjustable height, high cost. This stand does not fold and its height cannot be adjusted. But wooden racks are stable and durable, capable of decorating the interior.

8. Stand for mixer and laptop They are very helpful for many musicians when they need to connect the instrument to a computer or use various DJ equipment.

Fully adjustable laptop stand that can be used for a variety of DJ equipment such as CDs, keyboards, MIDI devices, projectors, etc. Two holders are adjustable in width and depth and securely hold laptops of any size without interfering with ports or slots. The laptop holder is height and tilt adjustable and rotates 360 degrees, allowing you to position your laptop perfectly. The stand is also equipped with a mouse holder, which can be placed on either side of the left/right side of the laptop or simply pushed in, which is convenient for storage and transportation.

How to make the right choice?

The choice of tool rack depends on its purpose and conditions of use. What to look for when choosing?

First, you need to consider the weight of the tool itself. Each model has in its characteristics the maximum weight of the placed tool. It is not recommended to exceed this weight, otherwise the stand may simply not support it and damage the instrument if it falls.

Secondly, focus on the ability to adjust the height of the stand. If a child plays the instrument, then you will definitely have to select the height of the instrument for him. In general, this is a very convenient option. Except wooden racks, almost all models have this characteristic.

Third, pay attention to how the stand folds and whether it folds at all. For transportation this is a very important function. Also, look at the mounting points, latches and adjusters; play can cause a lot of inconvenience.

Don't forget about appearance. If it suits you perfectly for performances and rehearsals metal stand, then for your home you can take a closer look at wooden stand and use it comfortably.

Although a keyboard stand is an accessory, it plays an important role because it allows you to make playing a musical instrument comfortable and reliable. Therefore, its choice should be approached responsibly. When choosing a stand, take into account the model of the musical instrument, as there are designs designed exclusively for certain synthesizers.

On YouTube channel POP-MUSIC you can see useful review ten popular models of keyboard stands.

For those who are learning how to play a synthesizer or who can fully play this instrument, it is very difficult to do without a special stand. And this is not surprising. After all, the instrument itself is quite heavy and has considerable dimensions. This is the reason why a synthesizer stand is required. However, the choice of such products is quite wide. If you are a beginner, then it will be difficult for you to decide on the type of rack. What are they and how to choose the right one?

Metal synthesizer stand

Today you can purchase XX, X and Z-shaped racks in specialized stores. They fit almost all types. A synthesizer stand made of metal has a number of advantages. First of all, this design differs from other varieties in its strength and lightness. There is no feeling of discomfort when playing a musical instrument.

Another advantage of such models is the ability to adjust the height. This synthesizer stand will ideal option for children. After all, they grow quickly. The height of the stand is easily adjustable. It can be gradually increased and, if necessary, decreased. This feature will allow an adult to play the instrument while sitting. And this is important for long and frequent lessons.

Which is better?

Lately there has been some debate about which synthesizer stand is better: X- or XX-shaped. According to many, the latter type of design is much more stable. However, its cost is significantly higher than the cost of the X-shaped one. It is worth noting that racks made of metal are more convenient and budget-friendly. This explains their popularity. In addition, if necessary, they can be folded and hidden in a place inaccessible to prying eyes. These stands take up little space.

Wooden structure

The keyboard stand can be made of wood. Such structures are usually made of chipboard. This is the most budget option. However, some manufacturers produce stands for musical instruments made of solid wood. Of course, the cost of a solid wood product is much higher and not everyone can afford it.

The main disadvantage of such a stand is that it is simply impossible to fold it and put it in a secluded corner. In addition, the height of the structure cannot be adjusted. This means that such stands are not suitable for children. Of course, wood construction also has advantages. Among them, it is worth highlighting the strength of parts and stability. In addition, the synthesizer will allow you to slightly enliven almost any interior.

Keyboard stand Axelvox KST-11

If you often rehearse performances or often practice, then you will need a reliable and high-quality stand for a musical instrument. The Axelvox KST-11 design has precisely these qualities. In addition, it is possible to adjust the height of the stand. In this case, the musical instrument will always be securely fastened.

The Axelvox KST-11 cross folding stand is made of fairly durable metal. The design is reliable and can last for many years. The design is equipped with a spring lock. This allows you to secure the musical instrument at a certain height. As a rule, the design is sold together with a cover. This allows you to transport the rack if necessary without the risk of damage.

Axelvox KST-21 stand

The Axelvox KST-21 keyboard stand is reliable and high-quality construction. Products of this model are made of powerful metal. The design is perfect for many modern electronic musical instruments. The Axelvox KST-21 stand is cross-shaped and equipped with a double frame. This provides additional reliability and stability of the product. If necessary, the structure can be transported. After all, it folds up easily.

Stand for Yamaha L85 synthesizer

The Yamaha L85 stand is ideal for mounting the P95 and P85. The structure is beautifully designed. The musical instrument is securely fastened, which ensures its safety during playing. The stand is attached to the bottom of the synthesizer. It is worth noting that the Yamaha L85 stand is ideal not only for home, but also for studio and stage.

Among the advantages of the product, it is worth highlighting its low weight and excellent stability. The stand is made in black. It is easy to install and attach to the keyboard. The Yamaha L85 stand is suitable for musicians of any level. Moreover, it is easy to use.

Stand CASIO CS-44

The structure is made of multilayer plywood and plastic. The stand provides an additional non-slip wide surface for a musical instrument and wide foot-stands. This product will fit perfectly into almost any interior. The casual design will make your musical instrument look more elegant.

In conclusion

A synthesizer stand makes it easier to play a musical instrument. However, its choice should be approached with all responsibility. First of all, you should determine who will use it, what qualities it should have and whether it will stand in one place. If a mobile design is required, then you should pay attention not to those made of metal. If you need to create original design room and make the conditions for playing the synthesizer more comfortable, it is better to purchase a wooden stand. When choosing a stand, you should also take into account the model of the musical instrument. After all, there are designs designed exclusively for certain synthesizers.

As a child, I had a piano, a real one, Soviet, about 300 kilograms. I liked to strum on it, and after graduating from music school, I even played something. The piano is cool, authentic, but not at all practical. And in order to be absolutely right for the soul, you also need drum kit, heels of gadgets for electric guitar, clarinet, sitar and sample loops...

Of course, now you no longer need to turn your apartment into a garage studio with a nest egg of six salaries; all you need to do is install a free music editor on your PC. But this is all inconvenient.

A PC keyboard is not at all like a keyboard instrument, everything is different here. Moreover, this is not at all suitable for teaching a child. It seems there is no choice but to purchase a synthesizer. But I still have doubts.

What is a synthesizer? A large device, with a musical keyboard, which should take up a lot of space somewhere. Which has built-in acoustics, but I already have a receiver with speakers. Which has a bad PC built into it, but I have a good PC.

It turns out that for 40 thousand I buy what I already have in best quality, with the exception of only the keyboard. This is just some maximum of irrational expenses.

While looking for a separate keyboard, I came across such a class of devices as USB MIDI Keyboard.
It always seemed to me that MIDI belongs to the field of professional musical activity.
But now all music is made on a PC, in any convenient place, which means that musicians need mobile music keyboards that can easily fit into a backpack.

A plan immediately formed in my head. We connect a MIDI keyboard to a home media center based on Raspberry Pi 3, where a software synthesizer is running, allowing anyone to perform their next masterpiece at any time. These MIDI keyboards usually have a set of controls and additional buttons that are programmed for various effects or additional musical instruments. It looks and sounds very cool!

There are larger and smaller devices, some more expensive and some cheaper. I chose the option for about 5 grand. It has two octaves, normal-sized keys, buttons for drummers, tuning knobs, that is, everything that a beginning electronic musician could dream of.

I'm not an expert in creating music on a PC, so it was difficult to look for ways to realize my idea. Information had to be collected bit by bit. The puzzle gradually began to take shape and I managed to put together a working solution, which I am sharing with you. Oddly enough, the standard Raspbian/Debian distribution contained everything you needed, you didn’t even have to connect external repositories.

Fluidsynth is used as a sequencer (an application that plays MIDI files).
The MIDI keyboard is immediately detected via ALSA and is available for connection to the sequencer.
To reproduce the sounds of various instruments, open sample databases in the SoundFont2 format are used. First, let's install all this.

Sudo -s apt-get update apt-get -y install alsa-utils fluid-soundfont-gm fluidsynth
We connect a MIDI keyboard to the Raspberry and launch the sequencer in server mode:

Fluidsynth -i -s -a alsa -g 3 /usr/share/sounds/sf2/FluidR3_GM.sf2
We execute the command:

Aconnect -o
As a result, we will see a list of available MIDI clients:

Client 14: "Midi Through" 0 "Midi Through Port-0" client 20: "VMini" 0 "VMini MIDI 1" 1 "VMini MIDI 2" client 128: "FLUID Synth (1628)" 0 "Synth input port (1628) :0)"
Here it is important for us to remember the client numbers of the keyboard and sequencer, so that we can then connect them with the command:

Aconnect 20:0 128:0
Now we are all ready to play on the Yamaha Piano (this is the default instrument). Read the fluidsynth manual, there's a lot there interesting teams, for example, to change the instrument to drums or winds, to set the amount of reverb or chorus.

Let's make our software synthesizer convenient. In order not to manually connect the keyboard to the sequencer every time, we will write a simple demon that will do this automatically at startup.

Cat > /etc/init.d/fluidsynth<< EOF #!/bin/bash ### BEGIN INIT INFO # Provides: fluidsynth # Required-Start: $all # Required-Stop: # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Fluidsynth deamon to play via MIDI-keyboard ### END INIT INFO startDaemon() { sleep 30s && fluidsynth -i -s -a alsa -g 3 --load-config=/home/osmc/midi-router >/var/log/fluidsynth & sleep 60s && aconnect 20:0 128:0 & ) stopDaemon() ( pkill -9 fluidsynth &> /dev/null ) restartDaemon() ( stopDaemon startDaemon ) case "$1" in start) startDaemon ; ; stop) stopDaemon ;; restart) restartDaemon ;; status) ;; *) startDaemon esac exit 0 EOF
Register the daemon for autorun:

Chmod 755 /etc/init.d/fluidsynth update-rc.d fluidsynth defaults
Please note that now at startup the sequencer is sent a configuration file (/home/osmc/midi-router) containing commands that turn our keyboard into a real synthesizer.

Here's the thing. Each key and knob on the keyboard sends certain events with its own number. As I understand it, there are no special standards here, so each manufacturer does what he wants. For example, I want the square keys to sound like drums, the rest of the keys to sound like piano, and the knobs to control volume, reverb and chorus.

So, I need to map the event codes from the keyboard to different instruments, and codes from knobs to codes that the sequencer understands. In fluidsynth this is done using router. It is these commands that are contained in the configuration file.

Here's an example of my config file, with comments about what it does.

Cat > /home/osmc/midi-router<< EOF # загружаем стандартные инструменты и ударники, найденные где-то на просторах Сети load /usr/share/sounds/sf2/FluidR3_GM.sf2 load /home/osmc/241-Drums.SF2 # связываем инструмент каждый со своим каналом select 1 2 128 0 select 2 1 0 0 # по умолчанию звук идет на канал 0 # перенаправляем события с квадратных клавиш на канал с ударными router_begin note router_chan 0 0 0 1 router_par1 36 48 1 0 router_end # события с остальных клавиш перенаправляем на канал с пианино router_begin note router_chan 0 0 0 2 router_par1 0 35 1 0 router_end router_begin note router_chan 0 0 0 2 router_par1 49 255 1 0 router_end # события с ручек мэпим на события, которые понимает секвенсер, # полный их список есть в документации на сайте fluidsynth router_begin cc router_chan 0 0 0 2 router_par1 14 14 0 98 router_end router_begin cc router_chan 0 0 0 2 router_par1 15 15 0 11 router_end router_begin cc router_chan 0 0 0 2 router_par1 16 16 0 91 router_end router_begin cc router_chan 0 0 0 2 router_par1 17 17 0 93 router_end # выключаем громкость на канале 0, # иначе при нажатии на клавишу # разные инструменты будут звучать одновременнно cc 0 7 0 EOF
To find out what codes your device generates, you need to use this utility:

Aseqdump -p 20:0
It listens and outputs events from the MIDI keyboard to the console. Press the button or turn the knob and you will see the event type, channel and code. You can program your keyboard the way you want, not the way the engineers who designed a particular synthesizer came up with it. For which many thanks to the developers fluidsynth, alsa, SoundFont2, Raspberry and V-Mini.

By the way, this topic with DIY synthesizers is reflected in several inventions, I recommend you study it.