In summer it is hot and stuffy, so the most valuable source that will help give you strength and restore vigor is water.You can equip an outdoor shower yourself, and there are several options for arranging an outdoor shower, which differ in design, operating principle and, of course, installation cost.
The advantages of a summer shower are that it does not require any expenses. Yes, in fact simple soul the water is heated by the sun. If you are on a wave of “unity with nature,” then the water in your summer shower must certainly be rain. Although, if there is a drought,you will need a device with which you will get water for your shower.
Making a summer shower
So, the most common way to equip an area with a summer shower is as follows.
A separate cabin is constructed from wood or plastic panels on a metal body, or maybe even brick. A water tank is installed on the roof of the cabin. Accordingly, as we said above, water can flow into the tank naturally and also heat up (rain and heat from the sun), and can also be pumped using a separate hose from the general water supply system of the house.A watering can is led from the tank into the shower stall. If you want the used water to leave the site, then during the construction stage of the cabin you will have to lay a drain through which the water will leave. To do this, you just need to build the floor at a slight slope or make a drain grate in the center. The outflow of water is simply necessary if the shower is used more than twice a day. If you rarely use a summer shower, then the outflow of water can be attributed to the natural process of absorption of moisture by the earth. The approximate cost of such a summer shower will be from two to six thousand rubles.
An even simpler option is a summer shower that operates on the pump principle. This option is the most economical and convenient. Such a summer showereasy to carry, which is especially beneficial for summer residents. So, a shower that works on the principle of a pump is also called a car shower. Its entire design is simple. It consists of a pump, two hoses and a watering can. One end of the hose is lowered into any container of water, be it a bucket, canister, etc. The pump in such designs is a foot pump, so you will have both hands free to wash yourself with all your heart. At the end of the other hose there is a watering can or a simple water distributor through which water is coming. Actually, this is the whole summer shower, which you can also build yourself. And if you have an automatic pump, thenperhaps such a shower will be even more profitable than summer shower cabin. The cost of a ready-made summer shower of this type with a foot pump costs about 500-700 rubles. A model with an automatic “drive” is equivalent toprice range from 40 to 120 dollars.
If we consider that a summer shower is not a full-fledged shower, but a means by which you can freshen up and wash away the main dirt, then from this point of view there are many more options for arranging a “pseudo shower”. But they are all built according to the same principle, in which a source of water is located above your head.
Summer shower - photo
Hot weather - very rare in most of our country. On cold days there is simply no way to heat the water in the container to the required temperature. There are not many people who want to take an ice-cold shower.
By country shower, most people mean simple design with a barrel on the roof. This shower has the following disadvantages:
- the water in the container blooms very quickly;
- there are constant problems with filling the barrel;
- it is impossible to maintain the desired water temperature.
To realize your idea, you need to familiarize yourself with the advice of craftsmen. Country shower will allow the family to comfortably take water treatments.
Mobile shower works according to to the following principle. Any container is installed next to the device. This could be a bucket or basin. Warm water is poured into it. After this, the end of the hose is lowered into the container.
The device that pumps water into the shower looks like a mat. A hose with a watering can is connected to one end of the pump. In this way, you can get a stream of water that will flow while stomping on the mat. This option is convenient because a mobile shower can be used not only in the country. The device will be useful for people who want to maintain hygiene while hiking. Even in such spartan conditions you can wash yourself. The advantage of such a shower is the ability to adjust the water temperature.
How to make a summer shower at the dacha with your own hands - for construction reliable design carefully select photos and sizes.
When building a stationary shower, the owner needs to decide where to divert the water. If there is already some kind of drainage hole on the site, then you can drain the water directly there. But this is not the best solution, since many people use bacteria to process wastewater. An increase in humidity will have Negative influence on the speed of purification of contaminated liquid.
During the construction of a shower room, it is best to make a separate drain hole. To strengthen the bottom of the hole, you can use broken bricks.
It is most difficult to strengthen a hole dug in sandy soil. Her walls will blur wastewater during operation. Therefore, it is necessary to line the walls of the sandy depression with boards.
The owner can save money when building a shower due to materials. To build a shower there is no need to build. During construction, foundations are most often used foundation blocks. They are leveled and the shower is raised 20 cm above ground level.
This height is enough to prevent the treated wood from rotting. When constructing a foundation, it is not necessary to use wood at all. You can weld a metal body and place it on paving slabs. If desired, you can strengthen the base by filling it with concrete.
There are no specific standards regarding the frame. A shower cabin, as a rule, consists of several parts. In one compartment you can arrange a locker room. There is a water heater in another room. It can use wood as fuel.
A room for storing equipment can be attached to the shower. If you are planning more lightweight design, then you can use the following option - instead of a door, hang a curtain. This will make the design easier and reduce construction costs. Be sure to take into account the height of people who will use the shower. Optimal height should be 2.2 meters. The width of the structure must be at least 0.9 meters. When making a frame, you can use not only metal, but also wood.
To make a metal frame, it is advisable to use corners with a thickness of at least 4 millimeters. The width of the shelf depends on the load. The frame will hold the water tank. What to do if you plan to supply a plastic container with a volume of 100 liters?
In this case, it is necessary to carry out the procedure of covering the shower stall on both sides with special clapboard. This material is considered the most practical. It has an attractive appearance and can withstand a humid environment for a long time. But for this it is necessary to treat the lining with a special solution.
To make a metal frame, you can use scraps metal pipes. The pipe wall thickness must be at least 3 mm. Otherwise, the shower structure may not withstand the load.
The frame can be strengthened using lathing. To do this, weld additional corners to the structure. With absence welding machine can be fixed with bolts.
To build a shower in the country with your own hands, you need to calculate the volume of the tank. For a family of 4 people you will have to supply a barrel with a volume of 100 liters. To make a wooden frame, you can buy timber. The beams are fastened using a tongue-and-groove system.
You can build a summer shower for your dacha with your own hands without using expensive materials.
Film is considered the cheapest material for covering shower walls. The disadvantage of this option is that the service life is too short. Within a year you will have to buy a new film. Therefore, summer residents prefer more reliable materials, which can last for several seasons.
It is better to give preference to impregnated fabrics. This material is used to make awnings and tents. When purchasing lumber, keep in mind that you cannot use fresh lining. The reason is that any lumber undergoes shrinkage.
During the drying process, the material loses its shape and previous dimensions. This affects the quality of lumber. Various defects may appear on its surface, reducing its strength. Warping and cracking are the most common defects that have a negative impact on wooden structures. In a structure built from fresh lumber, cracks may appear within a year. Do-it-yourself shower in the country, drawings, dimensions, photos are of interest to many users who want to warn themselves against these shortcomings.
For cladding, you can use the corrugated sheet left over after the construction of the fence.
Polycarbonate is a transparent material that will decorate any shower room. Do not allow any cracks to appear, as dust and moisture will enter them. This is a favorable environment for algae to grow. Gradually, the walls of the polycarbonate will be completely covered with greenish vegetation.
When constructing a shower, it is necessary to provide a ventilation system. Constant moisture can cause wood to rot. Fungus appears on the walls, destroying the structure.
Any container is suitable as a shower tank. It can be a metal or plastic barrel. However, plastic barrels heat water worse. For middle zone this can be critical, since the water requires heating.
The owner of a country house is unlikely to like ice water. Although plastic containers are cheaper than metal ones. But this is the only advantage of such barrels. It is best to install metal containers. Not only are they easier to install. The owners will not have to think about how to secure the metal barrel. In such a container, the water will heat up much faster. The process of heating water can be accelerated by painting the container black. The disadvantage of this option is the appearance of rust.
People wonder how to make a shower at the dacha with their own hands and how to choose the right water container; when studying photos of the building, you can decide the right choice structure and water tank.
Sometimes a septic tank is installed directly under the shower stall. In this case, the boards are laid with a gap of 3 mm. The water will flow down and fall directly into the drainage hole. In sandy soil, water will not stagnate.
But this septic tank option is not suitable for clay soil. To organize normal drainage, you need to dig a hole in another place. A pallet for building a septic tank can be bought in a store. The finished pallet must be selected based on the size of the future building. It is necessary to install bars around the entire perimeter, otherwise it will dangle.
The foundation can be laid out of bricks. At the bottom of the building you need to lay a layer of gravel 15 centimeters thick. After this, a drain pipe is installed. After the concrete has hardened, you can continue building the shower.
Most summer residents have a desire to take a shower after excavation work. The procedure has positive influence on human health. Of course, you can buy a ready-made shower. But this will increase construction costs.
It is cheaper to make a shower yourself, without the help of specialists. Water must flow at a certain slope. Don't forget to carry out waterproofing work on your shower. Using a waterproofing film, you can prevent the appearance of an unpleasant odor. To do this, you need to lay a special mesh. The recommended depth of the drainage pit is 2 m.
To retain heat, it is necessary to install a polycarbonate roof on top of the tank. It will create a greenhouse effect. Required element The tank is a sensor that informs the user about the water level. If there is no water, they may burn out. Therefore, it is necessary to constantly monitor this parameter. To install a shower floor, you need to install a drain pipe.
What to do if there is no running water in the house? To fill the tank you have to carry water in buckets. This is too time consuming. Before building a shower, think about the water supply. If you have running water, you can fill the tank fairly quickly. Just open the tap and wait until the container is filled to a certain level.
Advanced home owners have come up with a scheme that automates this process. This can be done using a float system. It is necessary to provide for the installation of a system that is designed to drain excess water. According to the laws of physics, the warmest water is at the top. Therefore, water is drawn from above. At the bottom of the tank you can install a hose to drain water into the sewer.
Of course, you can use the energy of the sun. At the same time, you do not have to spend money on electricity. However, this method has a significant drawback. It is difficult to warm up large amounts of liquid using the sun. In addition, this method cannot be implemented in all climatic zones.
In this case, you can use heating using devices that use electricity. Heating elements can heat water to the desired temperature. The person who decides to take a shower sets the temperature regime.
In order for the warmest water to flow into the watering can, you need to attach a piece of foam to the hose. Therefore, water is taken from above. To speed up the heating of water, you can make a coil.
The shower can be built at the farthest end of the site, near the fence. On sandy soil, water will not linger in the sump. Thanks to the rapid absorption of water, rotting of wooden materials used as cladding materials can be avoided.
When constructing a shower near a fence, the owner gets an advantage. In this case, it is enough to install 3 pillars. To prevent the pillars from wobbling, it is necessary to dig holes 78 cm deep, fill everything with crushed stone, compact it and fill it with concrete.
After leveling the floor, wood processing begins. You can buy aspen boards and impregnate them with a protective layer. Then the lumber is processed with a grinder.
When installing shelves, consider the weight of the barrel. It must withstand a load of at least 100 kg. The corners will rust during use. To increase service life, the metal frame is painted with a special paint that can be applied directly to rust.
To install polycarbonate, you can use self-tapping screws. Violation of technology can lead to cracking of polycarbonate sheets in sunny weather.
Therefore, people prefer a summer shower equipped with a heating system. To get a comfortable and practical design It is necessary to pay great attention to the construction site. A draft after a shower can lead to a cold. With the help of heating elements you can heat water to a certain temperature even in cold weather.
- There must be a distance of at least 5 meters between the shower structure and the drainage pit.
- TO earthworks You can proceed only after calculating the volume of the drainage pit. There is 0.5 cubic meter per person.
- When laying pipes, maintain a slope of 3 to 5 degrees.
The simplest design of a drainage pit is considered to be a cube shape. But this option has a significant drawback. The walls of such a pit lose strength.
It is best to use a cylindrical drain pit. In this case, the load is distributed evenly and the likelihood of destruction is reduced. In order to increase the service life of the shower structure, it is necessary to use biologically based products. Many bacteria are capable of processing waste. Water will be absorbed into the soil faster.
The advantage of a plastic tank is that the water in them does not bloom, the joints do not rust, and the properties of the water do not change.
Electric heaters can be supplied with my own hands. However, it is best to purchase a ready-made tank equipped with a built-in heater. In this case, the system controls all parameters automatically. The installation has a control panel and switches itself off in case of emergency.
In the shower high humidity. Therefore, during construction the following points must be taken into account:
- Instead of an iron pallet, it is advisable to use plastic ladders. They provide good air circulation and prevent water stagnation.
An outdoor shower is a necessary building at every dacha, especially if there is no pond or other places in the immediate vicinity where you can rinse off. The shower is a good way to freshen up after a hot day, or to wash away dust and dirt after gardening work. You can try to build such a building with your own hands. We provide tips and instructions on how to do this with a minimum of money and effort in this article.
A little about the benefits
The main advantages of a summer shower are:
- efficiency - to heat water for bathing in the simplest design, you only need the sun; you can wash without costly and time-consuming communications;
- convenience;
- accessibility for making with your own hands from scrap materials;
- the possibility of taking water procedures at any time of the year with good thermal insulation;
- some models allow you to shower anywhere;
- minimal maintenance costs.
Did you know? The prototype of modern showers are primitive baths that were built by the ancient Indians, Egyptians and Mesopotamians. They were partitions behind which people doused themselves with water, or ordered servants to do so. But the first showers, in which water flowed upward, were invented by the ancient Greeks. Proof of this is the images found on Athenian vases dating back to the 4th century. BC e.
Possible options
There are many options for building a summer shower. There are very simple and easy structures that take several hours to equip; There are capital ones that will serve for many years. After familiarizing yourself with the various options, you can use some ideas or take ready-made instructions as a basis.
Simple ways to arrange a summer shower
The simplest option for bathing in the country is a portable shower, which is sold in stores. It is a 20 liter water tank with a hose. The tank is hung on a tree or other vertical surface in a place that is well lit by the sun and filled with water. Once the water has warmed up, the hanging shower can be used. There is enough water in it to take water procedures for 10 minutes. 
A tank equipped with a tap can also be used as a hanging container. A hose ending with a shower head is attached to it. The tank will need to be attached to sunny place at a height slightly higher than human height (however, so that a person can reach the faucet with his hand).
One more in a simple way for arranging a bathing area is a lightweight shower structure that can be attached to the wall of any building. In this case, the wall will need to be covered with a special material that protects it from contact with water, for example, tiles or film. Such a shower can be either open or closed using a screen.
The stand is convenient because it can be installed anywhere where the water supply reaches.
The common disadvantages of the first three options is openness to prying eyes and winds. Usually, people swim under such a shower only in a swimsuit and in very warm weather. 
An option that is gaining more and more popularity due to its simplicity, compactness and affordability. To set it up you will need two corrugated hoses, two rubber pedals with valves (a rubber mat with a built-in pump), a container of water, and a shower head. The principle is that a person stomps on pedals or a mat with his feet, thereby pumping water from a container that flows into the hose.
A treadmill shower can be purchased ready-made in a store or made with your own hands using a car pump. 
This design involves driving four wooden (or other material) posts into the ground. They need to place a plastic tank into which water will be poured. It will also serve as the roof of the structure. A hose is attached to the tap in the tank, onto which a watering can is placed. The racks are covered with moisture-resistant material. The floor is a rubber mat.
A frame shower can be made from various materials. The simplest option can be built in a couple of hours. It can be made temporary, dismountable. That is, you can put it away indoors for the winter and take it out at the beginning of the new summer season. 
Important! When building a summer shower, you should choose black water containers. This way the water will warm up faster, since this color attracts the sun's rays best. In addition, the water temperature will be much higher.
The most complex and serious version of a summer shower without a foundation. This is a ready-made stationary shower stall with a door, equipped with a water tank and a tray. It is made of wood, polycarbonate, corrugated sheets, plastic or tarpaulin. The water tank can be heated either by the sun or by electricity. The cabin can be equipped with a dressing room-vestibule, in which things and shoes are left. It can also be made completely closed or semi-closed.
In addition to the design options described above, there are many design ideas for a summer shower. Using them, you can create a washing area to suit every taste and budget.
Capital buildings
In this subsection we have selected an overview of models that are made with pouring the foundation. Their walls are made of different materials:
- wood,
- gland,
- slate,
- plastic,
- polycarbonate,
- plexiglass,
- plywood,
- profiled sheets,
- bricks
Basic principles for installing a country shower
To build a high-quality, durable shower, several conditions must be met:
- pick up appropriate place;
- decide on the materials from which the tank, base and foundation will be made;
- think about how the drain will be arranged;
- estimate whether the shower will consist of one room, or whether the installation of a vestibule, toilet, etc. will be required;
- depending on how you plan to use the shower - throughout the year, or only in summer period- provide the possibility of heating water.
Selecting a location
The first thing that needs to be done is to choose a good place for construction. The following factors influence his choice:
- the water will heat up in a natural way, or automatic;
- it will be poured into the tank manually or automatically;
- what materials are planned to be used for the foundation and walls;
- dimensions of the building.
The shower will need to be installed close to the water supply, so as not to carry water far, or so that the hose can easily reach it. The choice of location will also be determined by what materials the body is made of, how much space it will take up, whether it needs to be hidden from human eyes, or whether it can fit harmoniously and beautifully into the complex of everything summer cottage. If you plan to install a tank with a heating element, then the shower room will need to be located in close proximity to the power supply.
Tank selection
The tank can be plastic, metal, polymer. A similar container can be purchased at a specialized store. You can also use any suitable thing - for example, an iron barrel, etc. - that can be found on the farm. Its volumes must be calculated based on the requirement of at least 40 liters per person. The maximum capacity volume is 200-250 l. Dimensions are selected according to the area of the building. 
As for the form, it is considered the most rational flat tank- it is easier to install on any structure, and the water is heated evenly. Round and square tanks are also common today.
If you prefer metal tanks, you should note that they should be treated with anti-corrosion agents and paint (except stainless steel). The service life of metal tanks with proper treatment is about 10 years. Stores usually sell containers made of galvanized, stainless, and carbon steel. The best and most expensive option is a stainless steel tank. They are usually rectangular containers with a capacity of 40 to 200 liters.
Plastic containers can last 30-50 years. Their advantages are lightness, ease of installation, efficient water heating, low maintenance requirements and low cost. Without heating, plastic containers hold 100-200 liters. They are equipped with lids at the top into which water is poured. Unheated tanks can be round or square. 
You can adapt a plastic or metal barrel for a homemade tank by cutting a threaded outlet at the bottom. In the future, you can insert a pipe or pump there.
Drain options
So, you have decided on the place of construction, the materials from which it will be made, and the type of tank. Now is the time to think about where the used water will go.
Important! If the withdrawal is not organized correctly,or is not organized at all, then after some time after use, problems may appear in the shower stall. bad smell, rot, mold.
Base and foundation
The foundation for construction can be of different types. The main ones:
The choice of foundation will depend on the type of materials from which the walls are made, as well as the volume of the water tank and technical characteristics soil. Availability of a toilet
A country shower can be combined under one roof with a toilet. This will save space and materials. You only need to fill one strip foundation, as well as equipment for only one drain. In addition, this will allow you not to litter the site with small buildings, because most dachas cannot boast of vast territories. And this is a significant time saving - building one compact structure will be much faster than two.
Possibility of heating water
If you plan to use the shower not only on warm sunny days, you need to consider the possibility of automatically heating the water.
Can be inserted into a heated tank a heating element power 1.25-2 kW. In this design, the water will heat up for about three hours. 
Heating element for heating water
Important! If you plan to install just such a tank, you should know that you will need to constantly monitor the presence of water in it - the exposed heating element will burn out when turned on. Therefore, such a container must have a constant supply of water by pump or water supply.
It is also advisable to equip it with a sensor that will show the water level. 
How to build a budget outdoor shower
A budget shower can be built from metal pipes and wooden planks. You will need the following materials:
- metal pipes (40 x 40 x 3000 mm) - six pieces;
- pine boards (20 x 95 x 3000 mm) - 21 pieces;
- plastic tank with a volume of 250 l;
- screws;
- sand;
- crushed stone;
- wood oil;
- enamel for metal pipes;
- geotextiles.
Tools you will need:
- Circular Saw;
- magnetic corner for welding;
- Miter saw;
- screwdriver
To reduce the cost of construction, instead of wooden walls, you can use, for example, tarpaulin or other material. However, in this case the construction will be very short-lived. Capital construction
If you are planning a long-term, high-quality construction of a shower that can be used in all seasons, we suggest you consider the following option: pile foundation and with a drain in the form of a septic tank. Recommended dimensions for a comfortable shower with changing room: height - 2-2.5 m, width - 1.40 m, length - 1.90 m. For accurate calculations of materials and dimensions, a drawing will be required.
Laying the foundation
The pile foundation can be made from metal pipes with a diameter of 100 mm and a length of 2 m each. For the foundation, draw a rectangle corresponding to the dimensions of the shower body. In the corners you need to drill four holes 1.5 m deep for the piles with a garden or ice drill, or dig them out with a shovel. To extend the life of metal pipes, they are treated with machine oil before being placed in the ground. 
Laying a pile foundation
After digging in the pipes, at least 30 cm should remain above ground level. The pipes must be filled with concrete.
After the concrete has completely hardened, you will need to install the timber and strapping. The frame is held together with long bolts.
Digging a septic tank
For the simplest version of a septic tank, a hole is dug in the immediate vicinity of the shower room, consistent with the dimensions of the receiving chamber, about 2 m deep. The walls are lined with brick or cinder block. Under the receiving chamber, you can use a barrel or other containers that can be closed with a lid. A chute is brought to the receiving chamber and connected to drain pipe. The drainage gutter is lined with waterproofing material. 
Frame installation
The shower frame is a welded structure made of metal pipes with a cross-section of 40 x 40 or 50 x 50 mm. This design will allow you to withstand a 200-liter tank of water. The booth itself can be made of wood, siding, corrugated sheets, or lining. You should consider the presence of ventilation windows in the walls, closer to the ceiling.
If there is no welding, then the structure is made of wooden beams 60 x 80 mm. In this case, the booth will also be wooden. Such a shower will be cheaper. The wood must be impregnated with special water-repellent agents.
After installing the vertical supports, produce top harness. The side frames are secured with spacers. 
The floor is made of wood. In this case, it will be warm and you can stand on it without shoes. The boards in the floor are made with a gap so that water flows freely.
The door is installed last.
The plastic tank is placed on the roof and secured with straps. Selected required diagram water supply.
Shower arrangement
A major shower will require electrical lighting wiring. In this case, it is necessary to adhere to safety rules and insulate the wiring to avoid contact with water. 
All interior decoration must be made of moisture-resistant materials. For a shower that is planned to be used throughout the year, insulation made of foam plastic or other materials will be required.
You should consider the placement of shelves for detergents, hooks for clothes and towels, internal lock for doors.
Another option for the capital construction of a warm country shower is on concrete slab with a frame made of wooden boards and OSB sheets- you can watch the video https://www.youtube.com/watch?v=vwhv_668wwo.
Did you know? The remains of an ancient shower complex, presumably dating back to the beginning of the 2nd century. BC e., were found by archaeologists in the territory of modern Turkey. It consisted of seven installations, into which water came from the main system, was supplied from above, flowed from installation to installation, and then flowed into the drainage system.
Summer shower - necessary outbuilding for summer residents who prefer to use their summer cottage both for recreation and for growing fruits and vegetables. It’s easy to make an outdoor shower cabin with your own hands, without having any special skills. However, even for simple structure some conditions will need to be met: choosing the most suitable place with a long exposure to it sun rays, ensuring unhindered drainage of used water. For more complex capital structures, it will be necessary to design and purchase necessary tools and materials.
Video: how to make a summer shower at the dacha with your own hands
Shower cabins for a summer residence are one of those “structures” that are easy to make yourself, but very difficult to do without. There are a huge number of different options for shower cabins, each master makes his own improvements to their design. We will not dwell on complex and expensive options; we will consider the most “budget”, but very functional solutions.
Before starting construction, decide what you want in the end, what capabilities and characteristics the shower cabin should have. The specific features of the shower stall depend on:
- the number of people living in the dacha. This indicator affects the volume of the tank for heating water and the need for drainage;
- landscape features of a summer cottage and physical characteristics of soils. It is better to install showers on small hills; this will allow you to do without special drainage in most cases. The installation location of the shower stall should be the sunniest, not very far from the dacha. It is advisable that in this place there are garden paths. Another important point is the availability of water. If you have any automatic water supply system, great, we will tell you how to automatically fill the container. If water at the dacha is obtained in buckets from a well, you will have to fill the tank on the shower stall manually;
- manufacturing materials. The frame can be made from shaped steel, square pipes or wood. Each material has its own characteristics. The walls are covered with clapboard, cellular polycarbonate or metal profile. There are cheaper options - stretch a tarpaulin, opaque plastic film or ordinary thick material over the frame;
- location. The cabin can be free-standing or attached to external wall country house. There are options for a mobile cabin - if necessary, it can be moved to a new location and does not require the construction of foundations. For such options, ultra-lightweight ones are chosen bearing structures and sheathing materials;
- engineering features of the water heating tank and shower drain control system.
Outdoor showers made of gabions 
Outdoor shower 
Outdoor shower made of brick (stone) 
Large wooden outdoor shower
You shouldn’t “save” on the size of the cabins; make it at least 2.2 meters in height, the dimensions of the base are at least 1x1 m. The fact is that the cabin should have space for bath accessories and clothes. Let's consider step by step two options for booths - with a metal and wooden frame.
Prices for summer shower
summer shower shower cabin
Shower stall with metal frame
Metal shower cabin 
Shower stall with metal frame 
Do-it-yourself shower cabin in the countryside photo
To carry out the work, you will need square pipes with a cross-section of at least 20×30 mm, sheet iron thickness from 1 mm and corner 45×45 mm. Tools – angle grinder (grinder) and welding machine.
GOST 8639 82 steel square pipes 
Galvanized iron sheet 
Corner 45 x 45
Step 1. Draw a sketch of the cabin.
The height of the booth is approximately 2.2 meters, the perimeter size is 1x1 m.
For rigidity, provide three rows of jumpers: at the top, in the middle and at the bottom. For the lower lintels it is better to use a corner; a wooden grid will be installed on its shelves. In the upper part you need to make stops to place the container under water; the specific sizes of the stops depend on the dimensions of the container.
Sheath side surfaces Can metal profile, cellular polycarbonate, plastic or wooden lining, or covered with various flexible materials. For each material, you need to think about places for fastening. Drill mounting holes in square pipe You can’t, weld metal plates for these purposes.
Don’t get too carried away with cellular polycarbonate for cladding. It is good in many respects, but only for a limited time. One of the disadvantages that manufacturers never mention is that over time, moss will begin to grow in the combs. And no seals will help; the power of nature will overcome any protective measures. The sight of polycarbonate sheets with moss inside will not make you happy, to put it mildly. In general, we recommend covering shower cabins with light and cheap soft materials. They can be replaced with new ones every season, the cabin will always have an attractive appearance without much loss of time and finances.
Metal sheet prices
a metal sheet
Step 2.
If you already have an idea about the structure of the frame, you can start making it.
Start by cutting metal elements. Cut 4 pipes 2.2 meters long (vertical supports). If you want to make opening doors in the booth, then you will need to cut two more pieces of pipe for them; the length may already be shorter; the door height dimensions should be kept within 1.5 m.
Under the grille stop you will need four corners of one meter each. The same length should be used to prepare pipes for the lintels of the side surfaces and doors. You will need two of them for each element of the cabin. You only need to cut parts according to the template, all angles are strictly 90°.
Very important: Follow safety precautions when working with grinder, injuries can be very serious. Some “craftsmen” install cutting discs in such a way that sparks fly in the opposite direction from them during operation. This is a grave mistake! In this position, the grinder is undermined with enormous effort; it is impossible to hold the tool in your hands.
Step 3.
Check the cut areas and clean them for welding. You don’t have to make a chamfer; the strength of the weld will withstand the load.
Step 4.
To increase the strength of the structure, prepare metal equilateral corners, the length of the legs is 5÷10 centimeters. It is advisable to install them at all corners of the frame and doors. Square supports ≈20×20 cm need to be welded under the feet.
Triangles to strengthen the structure
Step 5.
Welding the frame. Carry out the work very carefully, never immediately lay a full seam on one side. As it cools, it will pull the metal, making it very difficult to return to its original position. First, attach the adjacent pipes on one side, straighten the structure, and only after that can you lay a full seam on the opposite side. The seam has cooled down - weld the place where you baited.
For welding, you can use alternating voltage electrodes Ø4 mm.
This is the most universal diameter of electrodes; they can weld metal with a thickness of 1÷4 mm. Select the correct current strength; the metal should melt under the electrode to the required depth, but not completely cut through the pipe wall. If you have no experience performing welding work– It’s better to seek help from a professional. This will ultimately cost less than discarding expensive material yourself.
Work must be performed on a level area, constantly monitor the corners of the structure. The frame will stand on metal plates-legs measuring approximately 20x20 centimeters in size. Prepare them and cook them.
Prices for AC electrodes
AC electrodes
Step 6.
Frame assembly. You cannot do this work yourself; you need to call an assistant. Weld individual elements frame in the specified way, constantly check its spatial position. At the bottom, corners are welded on which the wooden grate will rest; on top, make a structure for a container for water.
Summer shower for the dacha - frame 
Step 7
Finishing. Carefully remove all burrs and sharp corners with a grinding machine, clean metal constructions from rust, oil and dirt.
Removing the weld seam At this stage you can stop or continue processing for a better result 
For painting, use special paints for metal. You will have to paint it at least twice, after the first time the metal will be visible. Do not use a pneumatic spray gun; it is only suitable for painting large surfaces. In your case, most of the paint will “go” into the air. Paint only with a brush; you will not need more than one to two hours for the entire painting.
In the photo - anti-corrosion compounds for metal
Next, you can make wooden grates for your feet and begin installing a water container. We will tell you how to install the container and connect the shower at the end of the article after describing the manufacture of the wooden frame of the shower stall.
Video - Do-it-yourself summer shower on the site
Shower stall with wooden frame
The linear dimensions can be the same as in the version with a metal frame. Material of manufacture – wooden blocks 50×50 mm, boards 50×100 mm, select specific dimensions taking into account the total weight of the water container. Boards and bars need to be passed through a thicknesser - the size will be equalized and roughness will be removed.
Step 1. Draw a sketch. It will come in handy not only during work, but with its help it is much easier to choose the optimal design option. It is better to correct your mistakes on paper than on the finished product. Draw several options on paper, think about the location of the stops, shelves and tank for the container. Compare several designs of shower stalls and choose the one that suits you best.
Step 2. Cut all the blanks for the frame to size; according to the design, it does not differ from the metal one. Once again, pay attention - watch the dimensions, make blanks only according to the templates.
Step 3. On level ground, begin assembling individual structural elements. It is better to make the connection in half a tree. If this is difficult for you, use it metal plates and corners on self-tapping screws.
Step 4. Assemble the individual frame elements into a single structure. If there are doors, secure them on hinges.
Instead of doors, you can make an ordinary curtain. Consider a location for installing the water tank.
Attach with inside shelves for bath accessories and hooks for towels and clothes. Prepare a wooden footrest.
Wooden grate - example 
Step 5. The ends of the vertical posts must be protected from rotting. You can treat them with special antiseptics, or you can soak them several times in drying oil or sunflower oil. By the way, drying oil is unrefined technical oil of oilseeds, including sunflower.
Drying oil prices
Let's give some practical tips on installing a shower stall.
Foundation
You can find advice to install shower cabins on screw foundation, pour a concrete platform under them, etc. We do not recommend doing such work for several reasons.
- Firstly, a shower stall is not a structure that requires special foundations.
- Secondly, we can guarantee you that over time you will have a desire to build a warm shower, and for this you will have to dismantle the cabin.
We recommend using paving slabs or wide paving stones for the foundation. Remove a small layer of soil underneath, level it horizontally and lay tiles in the prepared areas. Tamp it down a little - this will prevent the appearance of distortions while using the booth.
Video - Rules for laying paving slabs
Water drainage
And here you can find advice on the design of an entire engineering system. What does practice show? The volume of the water tank rarely allows more than two people to shower at the same time, the consumption for each is approximately 20÷30 liters. Depending on the weather, the water heating time ranges from five hours. We assure you that during this time the used water will quietly go into the ground. And one more thing - you shouldn’t be afraid that without a septic tank “unpleasant odors will appear”; this is not a sewer.
Water tank and shower
You can build the most beautiful and most reliable shower stall, but it will be very inconvenient to wash in it. Reason – incorrect installation water tank and shower. How to avoid such trouble? Let's give some practical recommendations.
Water container. You can use two options: plastic and metal.
Plastic containers
Advantages: relatively low price, wide choose in capacity, ease of installation.
But there are also significant drawbacks.
- Firstly, to improve heating efficiency, it is recommended to use plastic containers black, and this option is difficult to find and, moreover, to choose the optimal option in terms of capacity. It is almost impossible to paint a white container black.
- Secondly, the physical strength of the plastic does not allow you to reliably fix the shower connection point. Constant vibrations of the outlet pipe violate the tightness of the connection, and leaks appear. In addition, due to frequent bending forces in these places, the effect of material fatigue occurs. And this can lead to a complete separation of the shower with all the consequences.
Metal containers
Advantages - the high strength of the metal guarantees the tightness and reliability of the shower connection. The metal is easily painted black, and this color significantly increases the efficiency of heating water by solar rays.
Disadvantages: weight increases. You can ignore corrosion processes; a thick-walled barrel will last for decades. Moreover, a barrel filled with water corrodes much more slowly than an empty one. We recommend using metal barrels: cheap and reliable.
Construction and operation
Another important question is how to fill containers with water. Filling in buckets is not the best the best option. We strongly advise you to take all measures to ensure that water is filled with a hose. If your well or borehole is located at a great distance from the cabin, then you can make a temporary line with a flexible hose from the dacha. We will also tell you how to make water filling automatic. To do this, you can use an ordinary float made of cistern toilet. Adjust it to a response difference of approximately twenty liters of water, taking into account the size of the container. This will make it possible to constantly keep the barrel fully “filled”, the water will constantly heat up, and you will not have to prematurely end the shower process due to lack of water. Another advantage of “automation” is that the possibility of water overflow is eliminated. Overmoistening the soil near the shower stall is undesirable.
You may come across a proposal to take shower water from a container using a float. The end of the flexible intake hose is fixed on the float (you can take a piece of foam plastic of the appropriate size), as the water is consumed, the float will lower, the intake is always made from the top, warmest layer. This device has an effect, but it is insignificant. The fact is that the water in the containers heats up from the walls, the hot water rises, the cold sinks down. The movement of water through the volume occurs almost constantly, which means that there is not much difference in water temperature in the tank depending on the height.
Another improvement is to make electric heating, which will allow you to have warm water regardless weather conditions. Yes, the water will be hot, but who would dare to take a shower if the temperature outside is low? But this is not all the problems. During the device electric heating the rules of the PUE must be strictly observed, and they impose very stringent requirements for such work. In addition, you will need to install automatic switching on/off of heaters. Do you need such “complexities” in an ordinary outdoor shower stall? If there is a need to use a shower stall in cold weather, make a shower room in the dacha room. This decision will have to be made in case of a long stay on the site.
If you have a shower attached directly to the container (there is no shower hose), then you should take the complex additional measures for its secure fixation. Using stops (wooden or metal), secure the pipe, eliminating even the theoretical possibility of vibrations while using the tap. It is better to install the faucet of the valve type. It has a much easier rod stroke, the water pressure is gradually regulated, the working surfaces do not oxidize - the smoothness of the stroke does not change over time.
During the construction of the shower stall, consider the possibility of attaching small additional premises. They can be used both for extensions of the shower room or the installation of another one next to it, or for a separate dressing room.
Industrial shower cabins
Wide choice of both price and operational characteristics allows you to choose the best option taking into account your own preferences and individual characteristics of your summer cottage. Industrial shower cabins can be completely plastic, metal with lining various materials or tented. They are equipped with water tanks, cabins (metal or wood), pallets and cladding materials.
Shower for a summer residence, plastic 
According to consumer reviews, the booths are quite convenient to use, but there are several significant drawbacks. Plastic cabins do not meet the required strength indicators; if there are children at the dacha, then a season of work without repairing such a structure will be a great success.
The second disadvantage is the high price. A do-it-yourself shower stall will cost an order of magnitude cheaper. There are also quite cheap options for industrial booths, but in terms of strength they can be classified as “single-season”. Don’t waste your money; for this money you can build a wonderful, durable and reliable shower stall yourself.
Outdoor shower cabin “Economy” 
The third disadvantage is mass production designed for the average user. This is natural, everyone works according to this scheme manufacturing enterprises. By creating a cabin with your own hands, you can make all the calculations for yourself, change the location of the shower, its height, the diameter of the drain holes, adjustment mechanisms, etc. In addition, there are no restrictions on installation additional equipment, resizing in height and width, devices additional elements decor. There are craftsmen who make very original shower stalls.
Video - Country shower cabin with tent
Conclusion
Every suburban area requires constant improvement, do these things. You can start with a shower stall, then build a gazebo, then a bathhouse, and so on, from simple to complex. You will see personal experience- No better than that, which is made with your own hands.
Nothing relaxes you more after a hard day at work at the dacha than a summer shower. Water not only calms, but also refreshes, distracts from unpleasant thoughts and relieves stress. But what to do if there is no shower on site? If you don’t want to splash around in a trough or basin, you need to take care of comfort in field conditions and design a refreshing summer shower for your favorite summer house with your own hands, using finished photos and drawings.
How to build a summer shower with your own hands
The outdoor shower occupies one of the first places among all country houses. Sometimes this is not just a way to wash yourself after a day of cultivating the land has come to an end, but also the only way to cool down in the heat.
First you need to choose a place to install the shower structure. To do this, you should examine your site for secluded places.
On the other hand, this place should not be far from the main building, so that you do not have to freeze on the way to a warm house if you decide to take a shower on a cool day.
Advice! If a solar heated tank is provided, ensure that nothing obscures the water tank.
Once you have found a suitable location, select optimal sizes for your cabin. Please note that for ease of movement a person needs a room of at least 1 m 2. If a dressing room is planned for changing clothes and storing dry things while swimming, the building increases by another 60-70 cm. The height of the shower stall is approximately 2.5 m. So, the estimated dimensions of the shower for the dacha are 170x100x250 cm.
If the structure is supposed to be wooden, then the next stage of construction will be the construction of a frame made of wooden beams or a metal corner.
Next are the walls. Please note that for better ventilation, the walls should be no less than 20-30 cm away from the ceiling and pallet. The walls are constructed mainly from materials that were left over during the construction of the main dacha building.
Water supply in a country shower
When installing a shower for a summer house with your own hands, it is necessary to provide for the water supply and drainage in advance. The drainage system is laid during the construction of the foundation, and the supply of clean water is organized during the installation of the tank.
