Packing: 25
Package: 1
Plaster façade Bolars
DESCRIPTION:
Facade plaster – high-quality plaster for exterior work - on our website
Facade plaster BOLARS (gray) - weather-resistant, frost-resistant, waterproof plaster for facades on a cement-sand base using highly effective imported polymer additives.
Does not shrink and forms a smooth surface. Contains modifiers that prevent the formation of microcracks, as well as waterproof additives that determine the durability of the coating during operation.
Layer thickness 2-20 mm. Facade plaster is used for both internal and external work.
APPLICATION AREA:
BOLARS Facade (gray) is used for high-quality plastering of building facades and interior spaces with normal and high humidity.
Apply to concrete, aerated concrete, brick and stone surfaces.
PREPARATION OF SOLUTION:
Dilute 1 kg of dry mixture in 0.21-0.23 liters of clean tap water(for 1 bag 25 kg - 4.5 - 5.0 liters of water).
Mixing should be done manually or mechanized way(with a drill with an attachment), evenly pouring the dry mixture into the water until a homogeneous paste-like mass is obtained.
Let the solution stand for 5 minutes, after which it is necessary to mix it again and the solution is ready for use. The consistency is in working condition for at least 3 hours.
PREPARATION OF THE BASE, APPLICATION:
Before starting work, the surface must be hard and free of old paint, dust, grease and oil contaminants. It is recommended to treat the surface with BOLARS Primer Deep penetration.
The plaster is applied to the base in a layer of 2 to 20 mm and leveled with a rule or spatula. Work should be carried out at air temperatures from +5 °C to +30 °C.
Drying time 24 hours. Initial strength is achieved after 3 days. It is allowed to apply up to 30 mm in two layers with mandatory intermediate drying of 24 hours.
Before applying the second layer, treat the surface with BOLARS primer. Solution shelf life: at least 3 hours (30 minutes at -10 °C).
CONSUMPTION:
13-14 kg/sq.m with a layer thickness of 10 mm. A bag of 25 kg per 18 sq.m (with a layer thickness of 1 mm).
PRECAUTIONARY MEASURES:
Avoid getting the solution into your eyes. If the solution gets into your eyes, immediately rinse them with plenty of water. It is recommended to carry out work wearing rubber gloves.
STORAGE:
The guaranteed shelf life in a dry place and in undamaged original packaging is 12 months from the date of manufacture.
SPECIFICATIONS:
ColorGray
Drying time24 hours
The density of the mortar mixture is 1.7-1.8 g/cubic. cm
Amount of water per 1 kg of dry mixture 0.21-0.23 l/kg
Average density 1550-1650 kg/cubic. m
Thickness of the applied layer 2-20 mm
Adhesion not less than 4 kg/sq.cm
Compressive strength100 kg/sq.cm
Work temperature +5°С +30°С
Operating temperature -40°С +60°С
Frost resistance of at least 50 cycles
Suitability time of the solution for use is at least 3 hours (30 minutes at - 10°C)
Consumption 13-14 kg/sq.m (with a layer thickness of 10 mm)
PACKING:
Plaster is supplied in kraft bags of 25 kg
Plastered facade - perfect solution to protect walls from moisture and give them an aesthetic appearance. Products have proven themselves to be excellent Russian company Bolars. has a number of advantages and is in demand in the finishing work market.
What is Bolars Facade Plaster?
An effective composition for plastering facades. Contains special modifiers that prevent the appearance of microcracks on the surface. Imported polymer additives give the material excellent performance properties.
This coverage:
- Frost-resistant;
- Not afraid of exposure to moisture and natural factors;
- Applies evenly;
- Allows the surface to “breathe”;
- Plastering work can be performed manually or mechanically;
- Durable, proven well throughout its entire service life;
- Not subject to shrinkage;
- High adhesion;
- Dries quite quickly.
Specifications
Application area
BOLARS facade plaster is used for coating High Quality during external and internal finishing works.
The composition performed well in rooms with normal and high humidity. The basis is acceptable:
- Brick.
- Stone.
- Aerated concrete.
- Concrete.
Preparation of façade mortar
The BOLARS composition is poured into a hopper, and then the mixture is prepared mechanically strictly according to the instructions for the plastering machine.
The viscosity of the solution is selected taking into account the characteristics of the specific type of unit.
If the solution is prepared manually, the steps are as follows:
- A kilogram of dry plaster is diluted clean water in an amount of 0.4l - 0.42l.
- Water consumption per bag weighing 30 kg – 12 liters.
- Add the mixture little by little to the water and stir gradually.
- Using a drill with a special attachment or by hand, thoroughly mix the mass.
- After 5-10 minutes, the aged solution is stirred a second time.
- Can be plastered.
The solution is in working condition for no more than 3-4 hours.
Preparing the base
- Check the strength of the base. The peeling parts are removed.
- They carry out work on waterproofing and installation of drainage systems and utilities.
- Clean the surface from dirt, dust, stains that reduce adhesion to the base.
- The facade is treated with a suitable type of soil.
- Plaster façade surfaces possible after the primer has completely dried.
Application of facade plaster mixture
Video - :
Please note: the company produces Various types primers. The choice depends on the absorption capacity of the base:
- BOLARS Strengthening – for normal water absorption.
- BOLARS Deep penetration – for highly absorbent surfaces.
- BOLARS façade Anti-mold with fungicidal properties – in case of mold damage.
Precautionary measures
- Operations are performed with rubber gloves.
- Make sure that the dry powder and solution do not get into your eyes.
- If the solution gets on the cornea of the eye, rinse your eyes quickly big amount water.
- If the condition worsens, the appearance of discomfort in the eye, consult a doctor.
- Keep bags and prepared solution out of the reach of children.
Price of façade Bolars
A kraft bag weighing 25 kg costs 250 rubles. It is enough for 18 sq. m, if the layer thickness is only 1 mm. The cost of material when changing the thickness of the coating is easy to calculate.
25 kg. Scope of application Frost-resistant, weather-resistant high-strength plaster BOLARS Facade is intended for finishing the facades of buildings and premises with any level of humidity. Possesses high vapor permeability, which makes it possible to “breathe” the surface. Easily leveled, does not crack, does not form shrinkage cracks. Made on a cement-sand base using highly effective modifying additives. For work at temperatures down to -10 0C, a winter, frost-resistant version is available. Recommended bases Applicable manually or by continuously working on all concrete, foam and aerated concrete blocks, gas silicate, brick, masonry, cement-sand plasters. Preparing the base The base must be strong and have sufficient bearing capacity. Peeling, weak areas must be removed. Before starting work, the surfaces must be dust-free and cleaned of all types of contaminants that reduce adhesion. finishing materials. Before starting work on plastering facades, external waterproofing must be carried out and drainage systems must be installed. engineering systems. Finishing of facades with defects storm systems not acceptable. It is recommended to treat bases with normal water absorption with BOLARS Strengthening primer. Highly absorbent substrates must be treated with BOLARS Deep Penetration Primer. Before applying the primer, areas affected by mold fungi are treated with the fungicidal composition BOLARS Anti-Mold. Plastering of surfaces is carried out after the soil has completely dried. Preparation of the solution For mechanized application, the mixture is prepared in machines for mixing and feeding plaster mortar. Pour the dry mixture into the hopper of the plastering station. Adjust the water supply (the amount of water is determined by the type plastering machine) to match the required consistency of the solution. To prepare the mortar mixture for manual application, you must take a precisely measured amount of clean tap water. room temperature(for 1 kg dry 0.20-0.23 l of water, for 1 bag of 25 kg - 5.0-5.75 l of water). Mixing is carried out mechanically (with a drill with an attachment), evenly pouring the dry mixture into water until a homogeneous paste-like mass is obtained. Let the solution stand for 3-5 minutes, then stir again and it is ready for use. Ready solution is in working condition for at least 3 hours. Execution of work Treat the prepared facade plaster solution using the machine spray method or apply it with a trowel, trowel or spatula to the base in a layer of 2 to 20 mm, then level it using a rule or grater. When plastering brick walls and surfaces made of gas silicate blocks, it is recommended to use façade fiberglass mesh. To obtain an even, smooth layer, after the mixture begins to set on the wall, smooth the surface with a metal spatula. Application in two layers is allowed (total application thickness up to 30 mm). To do this, comb the first, not yet hardened, layer with a plaster comb and dry completely. Before applying the next layer, the surface must be treated with BOLARS Strengthening primer. For final leveling It is recommended to use materials from the BOLARS putty group depending on the type of base and work conditions. Consumption Average consumption for a layer thickness of 10 mm is 13-14 kg/m². 25 kg bag – 1.7-1.8 m² with a layer thickness of 10 mm. Working conditions The specified time characteristics are valid at temperatures environment+20°C, relative air humidity 60%, may vary under other temperature and humidity conditions. When carrying out work and over the next 3 days, the temperature of the air and the base should be in the range from +5°C to +30°C. The temperature of the mortar mixture during the work must not be lower than +5°C. It is not allowed to apply plaster in rainy, windy weather, or in the presence of surface condensation. During the process of gaining strength, the plaster should be protected from drying out, drafts and direct sunlight. Limitations To avoid reducing the strength characteristics of the plaster, it is prohibited to overfill water in excess of the norms specified by the manufacturer, and additional introduction other components ready mortar mixture. When the solution thickens in the working container, it is mixed a second time without adding water (within the viability time of the solution). When conducting interior works Adequate ventilation must be ensured. Forced drying of the plaster layer using is not allowed. Precautions If the solution gets into your eyes, rinse them with plenty of water. It is recommended to carry out work with rubber gloves. KEEP AWAY FROM CHILDREN!
Bolars facade plaster (gray) - sale in Moscow. From us you can purchase the product “Bolars facade plaster (gray)” at a price of 253 rubles. In order to buy this product, click on the “Show phone” button.
Facade plaster "Bolars" is used for both exterior and interior work. The Bolars company has been producing materials for construction since 1999. It was 17 years ago that a product under this brand was first released. Today Bolars is a popular and well-known leader in the sale of plaster.
The production itself takes place using new modern technologies. Properly organized management is combined with plans to “build” long-term cooperation. Product quality is at the highest level.
The company operates thanks to a developed infrastructure, namely:
- Factory.
- Several scientific laboratories who are involved in quality control of initial raw materials and final products.
- Departments involved in statistical testing.
- Wide network of warehouses and representatives throughout the territory Russian Federation, and in neighboring countries.
All mentioned laboratories have passed the necessary certification, and the plant operates on technologies that allow automatic control of all production. The main idea of the company is the production of goods best quality while maintaining low prices. The quality meets all international standards.
What is facade plaster "Bolars"
Created on a sand-cement base, using high-quality European polymer elements.
The advantages include:
- No shrinkage and formation of a smooth surface.
- Manufacturers included modifiers, which prevent coating cracks, waterproof additives that ensure a long and pleasant period of operation.
- The mixture is applied in a layer of 2 mm to 2 cm.
Where we use it
Facade plaster bolars 25 kg is used to qualitatively finish the external facades of houses, as well as interior walls rooms with normal humidity levels.
It fits well on the following surfaces:
- Stone.
- Concrete.
- Brick (see How plastering is done on brickwork).
DIY cooking instructions
So:
- Add 0.2 liters of ordinary water to 1 kilogram of dry plaster.
- If you are diluting a bag, you need 5 liters of water.
- You need to add it gradually, stirring.
Note. This can be done in the usual way, manually, or use mechanical devices, for example, a drill with an attachment. The result should be a homogeneous, paste-like mass.
- Leave to sit for 5 minutes and mix everything again.
The solution must be used within 5 hours; it is not suitable for longer.
Prepare the surface and apply
Before starting surface treatment, you need to check if it:
- Solid.
- Removed old paint.
- Cleared of dust.
- Free from fat and oil.
Stages of work:
- The walls or facade must be treated with a high-quality primer (see Facade primer - its types and application), preferably from the same company as the plaster.
- It is recommended to apply plaster to the prepared wall in a layer thickness of 2 mm to 2 cm.
- You need to level the applied mixture with a rule or a spatula. The video in this article will tell you more about the application.
- It is necessary to monitor the temperature of the room in which the repair is taking place.
Note. The temperature should not fall below +5 °C and above +30 °C. The layer dries within a day.
- The mixture gains its strength after 3-4 days.
- You can apply it in two layers, so that the overall layer is 3 centimeters thick. But between each application, at least a day must pass.
Weather-resistant plaster of increased strength. Designed for finishing the facades of buildings and premises with any level of humidity. It has high vapor permeability, which allows the surface to “breathe”. Easily leveled, does not crack, does not form shrinkage cracks. For manual application on concrete, brick, aerated concrete, stone and plastered surfaces. Made on a cement-sand base using highly effective modifying additives.
Material consumption
The consumption of the mixture depends on the topography of the base. 13-14 kg/m2 of dry mixture with a layer thickness of 10 mm.
Precautionary measures
It is recommended to carry out work wearing rubber gloves. If the solution gets into your eyes, immediately rinse them with plenty of water. To protect the respiratory system, use respirators, and to protect the eyes, use safety glasses.
Packing and storage
Supplied in multi-layer paper bags of 25 kg. Shelf life in a dry place in unopened original packaging is 12 months.
