The slopes on the doors are your own. Slopes for entrance doors. How to seal the slopes of the front door

Installing a new door is not the end of the doorway design process, but only its beginning: everything does not look very presentable and creates the appearance of an unfinished renovation. If the door is an entrance, this concerns not only the aesthetic side of the issue: the polyurethane foam, while it is not yet protected from the outside, accumulates moisture. Because of this, heat leaves the room, and cold and noise penetrate inside through the cracks. To avoid all these troubles, it is necessary to finish the door slopes. You can do the work yourself - it is not complicated and, if you have the ability to use tools, it is quite within the capabilities of a home craftsman.

How to make slopes on the front door

For revision doorway several stages of work will be required, such as insulation, creation load-bearing base and the final stage - decorative finishing.

Let's consider the options interior work for finishing door slopes.

Application cement mortar. Using a solution is reliable and inexpensive for pre-finishing slopes interior doors. But don’t forget – working with the solution is the most labor-intensive. For wide slopes to close the gap cement mixture you will need a lot of material.

To obtain an ideal result, the master must be able to prepare the mixture and apply it correctly. When choosing a finishing material, you need to take into account the design of the room - it is chosen in such a way that the decorative finish of the door slopes is in harmony with color scheme and room decoration.

Application of the frame. The frame can be installed in advance or after the door is installed. Then they attach it to it finishing elements – wooden lining or PVC panels. This method is the fastest solution, guaranteeing perfect results. Moreover, this way you can not only get a very smooth surface, but also hide it in door block telephone or electricity wires. The disadvantage of this option is weak strength. Because of this, it is not recommended to use frame decorative finishing slopes for entrance doors - it is easy to break.
Finishing tiles. On brickwork Tile adhesive is applied and the tiles are laid. Angles between door jamb and tiles are covered with grout, and between the tiles and the wall of the room they are sealed with a plastic or wooden corner.

Read also: We lay a wooden floor on the balcony with our own hands

Installation technology without using a frame: plastering

There are several options for finishing slopes front door, but any of them begins with checking the correct installation of the door itself - whether it is installed vertically, whether the seams are sealed. You can check the tightness with a lit candle, passing it around the entire perimeter. If the flame fluctuates, you need to add sealant.

To finish the slopes of an interior or entrance door from the inside, experts recommend first gluing masking tape to their surface. This is necessary to protect the canvas and box. Then the loose masonry and dust are removed and the plastering process begins.

It all happens as follows:

The surface is covered with a primer material. Deep penetration material is most suitable for this purpose. It is necessary to ensure strong adhesion of the layers and strengthen the base. The lintel on top of the door needs to be treated especially well.
When the primer has dried, use a level to install the beacon profiles - they are needed to work with the rule.
After installing the beacons for finishing the slopes after installing the door, you need to prepare a mixture for fixing. It is best to use river sand (3/4 parts) and cement to prepare the solution. M-200 or M-150 will do. You will need 1/4 of it. Water is added little by little until a solution enveloping the instrument is obtained.
The finished solution is forcefully thrown onto the wall surface using a spatula or trowel until the profile is completely covered.
After filling a small area, each time they check the correct operation by applying the tool to the beacons. This will ensure a smooth surface.

Drywall installation

Usually, few home craftsmen know how to make a plasterboard slope on a door, but meanwhile, this is the simplest option. To do this, you do not need to level the surfaces or use other materials. The main thing is that the door is positioned correctly. If a small error is noticed, you can eliminate the defect with a layer of plaster (thickness no more than 1 cm). If the slopes are severely damaged, first level the opening with plaster and only then attach the panels.

Read also: What to do if the walls are crooked? Do-it-yourself visual alignment of walls

Subsequent steps for finishing the slopes after installing the front door look like this:

Carefully prime the base for drywall.
Measure the slopes and make markings. Double-check the marks using a square and tape measure.
Cut sheets according to required size. Apply glue to the prepared sheet of drywall using the square-cluster method. The application step is 15-20 cm. The diameter of each glue spot is 3-5 cm.
When the glue dries a little, take the drywall and place it in the desired place.
Align the sheet and press it firmly with your palms. Do the same with the remaining parts.
When the glue is completely dry, install it on external corners painting profile.
Finish the corners of the slopes and walls with a special mixture.

Using the Frame

How to make slopes on a door with your own hands if it is made of heavy material, so that no unpleasant surprises happen during operation? This usually happens when, for example, an opening metal door finished with concrete: after a few months, under the weight of the door leaf, the plaster will begin to crack. Accordingly, in order to protect the slopes from the weight of the door, it is necessary to choose the right finishing material. In the case of a metal door, it is best to make slopes using a frame. This will allow:

Prevent deformation.
Eliminate excess space around the slope.
Use heavy sheets for work. For example - MDF.

When using a frame, you can finish not only the slopes of the front door, but also perform work in those rooms where it is possible increased level humidity - in the bathroom, kitchen, hallway.

For the construction of the frame, they use antiseptic-impregnated wooden slats. Suitable aluminum profile. Next - how to make front door slopes with your own hands:

Prepare the opening. Clear away debris. If there are cracks, seal them.
Apply an antiseptic primer after the solution has dried.
Set up the timber (profile). Fix it to the permanent base with dowel nails. Also install and secure the second stand.
Install parallel posts around the perimeter. To strengthen the structure, it is necessary to install longitudinal lintels for subsequent finishing of the entrance door slopes with panels, connecting both parts with them.
Lay the communication cable.
Make as accurately as possible according to the right sizes planks. Secure them with liquid nails. This must be done so that the gap between separate elements was minimal.
Strengthen the fastening using self-tapping screws.

Read also: Do-it-yourself application of liquid wallpaper (decorative plaster) – room for creativity

Features of finishing

To properly make slopes on the front door or on interior doors, you need finishing perform the most suitable material. But this is only if one is needed. For example, the use of MDF does not require the use of additional finishing: the surfaces of the material are highly decorative. Therefore, the only thing that may be needed is to purchase platbands and disguise the joints. Of course, mastic or furniture stickers need to be matched to the tone of the main decoration of the room.

If for finishing slopes internal doors plaster was used, then you can paint the surface, decorate it with decorative plaster, and cover it with wallpaper. Before painting the slope, it is covered with starting and then finishing putty - this will make the surface smooth. When the plaster dries, apply a primer on top of it, then a water-based emulsion, and cover it with acrylic paint on top.

When finishing the slopes of the front door from the inside, wallpaper is rarely used today - it is difficult and time-consuming. However, a few tips from the experts will help you cope with the process faster:

There is no need to apply wallpaper after the door installation is completed. This needs to be done when the walls of the entire room are finished.
It is not advisable to stick wallpaper with a pattern near the door.
The canvas must be designed so that it can cover the entire slope in width.
You need to cut off the fabric with excess - this is necessary for overlap.

Conclusion

All of the above technologies have their own nuances. Therefore, when deciding how to make slopes on interior or entrance doors, you need to take into account all factors. Any of these can influence the choice of materials and type of construction.

Choose the most for yourself suitable option The photos below will help you finish the door slopes.

The slopes on the doors are not only an insulating element of the door decoration, but also perform an aesthetic function. The process of installing slopes on doors requires special attention, because they exist different ways and finishing technologies. In this article we will consider issues related to installing slopes in various ways.

Methods for designing slopes

Exist different variants for installation door slopes, which are determined by the type of material, work technology, etc. When installing it yourself, it is important to follow the recommendations of specialists and detailed installation instructions. It is important to ensure that the materials used are practical and durable, and they must also perform insulating functions, especially when finishing the slopes of the front door.

The installation of door slopes must meet certain tasks, which include reliable fixation of fasteners, as well as the implementation of decorative function. When determining variations in the finishing of slopes, experts identify surface cladding with different materials, which are attached to the base with the assistance of mortar and plaster. Some elements can be attached to the frame base using a drill or other devices.

As finishing objects, you can veneer door slopes made of laminate, plasterboard, plastic or wood panels, MDF and the like. All materials are perfect for finishing, both for interior doors and entrance doors. In the latter option, it is necessary to ensure reliable sound insulation and complete sealing, which requires careful sealing of the slopes.

The slopes for the front door should not have any voids, which increases the strength and reliability of the cladding. Can be used over putty or mortar different materials for finishing. The main thing is that they are combined with interior design apartments or houses. If a huge amount of mortar is needed for finishing, for example, to level corners, then a frame can be installed on the slopes. Its base can be wooden slats or metallic profile, on which facing materials are installed.

It is worth noting that finishing the slopes under the frame will create a smoother surface than plastering. Moreover, finishing with wooden or plastic panels looks more attractive than painting the surface and so on. In particular, it is much easier to carry out telephone, electrical and other communications through frame slopes.

It is important that the doorway has a maximum service life, is durable and practically resistant to mechanical and other damage. To do this, you need to know the rules and technologies for installing slopes on doors yourself. No less importance is given to the choice facing material, which are distinguished:

1. Finishing with drywall. Such material will hide all the unevenness of the slopes. Using this option, you will get rid of unnecessary waste on purchasing putty and other solutions intended for leveling a certain area. In this case, there will be no possibility of installing a frame base.

2. Plastering the slopes on the door. This method is considered the most economical and practical, and all the work can be done independently. For this, it is important work surface cover with plaster, after which you can start finishing.

3. Plastic panels. Very often used for decoration window openings. They are rarely used in door openings, because plastic materials will stand out from the background wooden product. Moreover, this option is not reliable and durable.

4. Wooden slopes. This finishing option is the most popular. Wood is durable and reliable material which one will serve for a long time. This finish will suit different interior rooms.

Drywall door slopes

Drywall is not used for finishing, but is the basis for slopes. This option is used to save money on purchasing different mixtures for leveling walls. Installation work should start with preliminary preparation surfaces, which includes cleaning the walls, as well as priming:

1. After the surface has dried, you need to take all measurements and prepare materials for finishing the slopes on the front door with your own hands. When cutting the material, make sure that some parts are cut at an angle. This is necessary for attaching parts to a tilted surface.

2. After cutting the sheets, check that all elements fit under the doorway.

3. Next, you should wait for the primer layer to dry completely, after which you can install the panels. Special glue or dowels can be used as fasteners. It is recommended to use the first option, which will allow you to fasten the sheets of drywall more evenly.

4. The installation process should begin with the installation of the side parts of the opening, and finally, the upper area can be finished.

5. Glue can be applied in a continuous strip or in separate dots, for example, every 15 centimeters.

6. After securely fixing the drywall sheets, it is necessary to finish the surface by attaching perforated corners using putty.

Finishing door slopes with plaster

This type of work does not present any particular difficulties and requires minimum costs. The process of finishing slopes with plaster has the following sequence:

1. First, the working surface must be cleaned and primed.

2. After the primer layer has dried, it is recommended to begin applying the solution to the surface of the slopes. It is recommended to use a spatula for this work.

3. To ensure that the corners of the opening are even, it is important to use perforated metal corners. They are attached to the surface using a layer of plaster and carefully covered.

4. After the plaster has dried, the surface of the slopes should be cleaned using sandpaper.

5. The last stage is the treatment of walls using paints and varnishes that will add aesthetics.

Finishing slopes with plastic panels

You can make door slopes with your own hands from plastic panels. The work is carried out in the following sequence:

1. First, you need to take measurements of the door slopes and cut plastic panels that would correspond to these parameters.

2. You should use electric jigsaw, not a regular knife. This is necessary so that all parts in the cut areas are even.

3. After cutting, all panels must be checked against the doorway.

4. First, install slopes on the sides. For this purpose, a special profile is fixed to the opening using self-tapping screws.

5. Wooden slats must be attached to the edge of the wall. It is important to check the evenness of the installation elements with the assistance of the building level. Plastic panels will be attached to such slats using staples.

6. In the lower area, a plug is installed on the plastic panels, and the finishing item is inserted into the slopes on the sides and into the initial profile. The same procedure applies to finishing the slopes above the doors.

7. The last step is processing and sealing the seams using silicone. For installation plastic slopes It is recommended to choose PVC sheets, as well as special sandwich panels.

Finishing slopes with wood

Wood finishing is perfect for both metal and wooden door slopes. Of course, you can use materials made from natural wood, or use laminated or MDF panels. If you want to choose a material that has excellent insulating properties, then it is recommended to use MDF boards. If their parameters do not fit the dimensions of the slopes, then laminate can be an excellent alternative.

At first, installation work begin with careful sealing of the seams between door frame and the surface of the wall. After this, the remaining foam must be removed, cleaned and carefully primed. Slopes can be made at right angles or with slight slope. After determining the shape of the slopes, it is necessary to fix all the panels. During work it is necessary to carefully monitor correct selection wooden planks. It is important that they have the same thickness and dimensions on both sides.

The slats or frame must be attached to the wall with the assistance of dowels, which refers to the fixation of all parts. The slopes can be attached using glue or using self-tapping screws. All gaps must be sealed with silicone sealant. Slopes made of wooden panels look very aesthetically pleasing in any interior.

Detailed instructions for installing slopes for entrance doors

Finishing work must be carried out taking into account the size of the doorway and the materials used. If, when installing slopes in interior openings there is no need to do insulation, then for entrance doors a similar procedure is important element. To answer the question: how to make slopes on the front door, it is necessary to pay important attention to sealing the openings from drafts and sounds coming from the landing.

Slopes must be strong and reliable. In this case, experts suggest finishing with plaster or using different combinations. For example, you can plaster the walls on top of which MDF panels are mounted. Everyone uses items for decoration according to their own preferences. To carry out the work, you need to prepare the following materials and devices:

polyurethane foam;
lime, cement;
putty, primer;
sand;
glue, dowels, if necessary, “liquid nails”;
electric jigsaw;
building level;
brushes, spatula;
perforated corners.

To answer the question: how to make door slopes even? - we recommend studying detailed instructions performance of work.

1. First of all, it is important to seal all the cracks. After installing the door, it is important to carefully fill all the gaps between the frame and the wall with foam. Next, you need to wait until the foam hardens. All remains must be cut off with a regular knife and the cracks carefully smoothed out.

2. Surface preparation is important for further plastering of the wall. All work takes a long time, so it is recommended to treat the surface in several layers. First, a layer of primer is applied to the wall, which will better strengthen plaster mortar. To achieve a perfectly flat surface, you need to use a beacon profile, which is fixed with dowels.

3. Next, we carry out plastering of the slopes. To make the solution it is necessary to use cement, sand, mortar. The technology for applying the mixture to the surface must begin from the upper area of the slopes. First, the putty is applied in a thick layer, after which the excess amount is removed by leveling the wall. To ensure even slope angles, it is recommended to use a perforated profile. They are fixed on the surface of the applied plaster mixture. Next, a finishing layer of plaster is applied, which should be thin. This process will remove all unevenness and roughness.

4. The final stage is attaching the MDF panels. The base for such panels should be made of lime-cement mortar. After it dries, a layer of primer is applied to the surface. The panels must be divided into three parts, each of which must correspond to the door slopes. A layer of glue must be applied to the surface of the wall, after which the panels are applied to the wall. Such work must be done with all the details.

To understand the scheme of work, we recommend watching the video about finishing door slopes, presented at the end of the article. When finishing, you need to pay due attention to cutting the slab. To do this, all angles are carefully measured, and it is important to trim the panels at a certain angle. After cutting the plastic or wooden panel, all the parts need to be connected to check whether they correspond to the door slopes. The perfect combination finishing the slopes will be the use of wooden panels and doors made of such material.

Even new and beautiful doors will have unattractive appearance without properly executed slopes. Modern construction technologies allow the use of a variety of materials for finishing. In addition to improving the appearance of the doorway, slopes help solve a number of other problems. If they are made correctly and competently, they increase the tightness, heat and sound insulation characteristics of the door, and also prevent physical break-ins.

Functions and design of door slopes

A door jamb is the area around a door or empty opening. Application modern technologies and materials allows for a variety of design finishing of this place, after which it becomes one of the decorations of the room, emphasizing the tastes and preferences of the owners of the house.

A properly executed door slope at the entrance to a house or apartment will help get rid of many problems, ranging from noise and cold penetrating into the house, and ending with increasing the safety and comfort of housing.

The door slope should fit harmoniously into the surrounding interior

The door slope performs the following functions:

heat insulating. After him proper finishing heat or cold from the street will not penetrate into the house;
noise canceling. A properly executed slope will not allow entry into the home extraneous sounds from the street or from the entrance;
aesthetic. By choosing the right finishing material and installing it in accordance with the developed technologies, you can decorate the room in an original way and make it bright, memorable and unique;
protective. After installing the slopes, the burglary resistance of the door block increases.

The finishing of the slopes begins after the door is installed. First, the top part is installed, after which you can begin installing the side elements.

Features of the device of slopes in the doorway

If you look at the door slope in section, you can see that it is made according to the sandwich principle and consists of several layers arranged in a strict order. Only by following the installation technology can you correctly install door slopes and get not only high-quality, but also beautiful results.

The door slope consists of the following layers:

Materials used for finishing door slopes

There are many options for finishing door slopes, so when choosing materials you need to take into account your preferences and financial capabilities, as well as the features of the interior. Most often used:

PVC panels. The choice of plastic thermal insulation panels is one of best options when finishing slopes of entrance doors. This is due to the high heat and sound insulation characteristics of the material, its durability and sufficient strength. The main advantages of finishing slopes with PVC panels:
Drywall. This is the most common finishing material with which you can simply and quickly decorate doorway. Working with drywall does not require special tools or skills, so you can easily handle its installation yourself. After laying the drywall, you will have to use finishing materials; their choice depends on the preferences of the owners. Finishing can be done in two ways:
Plaster. To use this finishing option you must have certain skills. You can take not the usual one, but decorative plaster, this will allow you to get a more beautiful and original result. Perlite mixture is often used for these purposes. Its only drawback is its high cost. One centimeter of such material in its own way thermal insulation characteristics corresponds to one brick masonry. Any plaster must be applied in several layers and wait a certain time until they dry. Therefore, such work takes a long time and requires serious physical effort.
To plaster door slopes you must have the appropriate skills
MDF panels. They allow you to decorate a doorway of any width. This finishing material, like drywall, can be mounted with glue or on a frame. For wide openings, the second option is more acceptable. In this way, you can finish slopes up to 80 cm wide. MDF panels can be lined with natural veneer, and then covered with varnish or laminated film of the most different colors. This allows you to beautifully design the doorway and select finishing materials to suit any interior.
MDF panels can be used to trim slopes up to 80 cm wide
Decorative rock. Although this is an expensive material, finishing door slopes with it allows you to get a beautiful and original solution. In order not to overload the interior, it is recommended to use medium-sized decorative stones. The main advantages of this option:
Other options. If you want to make an exclusive and unique door slope, you can use natural materials. This can be cork bark, bamboo planks and other materials. Their advantage is that they do not cause allergic reactions, so they can be used in homes where people and small children who are sensitive to dust and foreign odors live. In addition, static electricity does not accumulate on them, so dust does not stick. Natural materials go well with all types of doors and help create a harmonious and peaceful atmosphere in the house.
Natural wood does not cause allergic reactions and looks very beautiful

Video: how to hide crooked slope angles

Plastering door slopes

Although plastering door slopes requires certain skills, if you have the desire, then, by adhering to the developed technologies, it is quite possible to cope with this task yourself.

To complete the work you will need the following tools:

In order to save mortar when filling large potholes, they can be filled with pieces of foam plastic and then plastered over.

You can plaster door slopes with different compositions:

WITH ready-made mixtures easier to work with, but prepared yourself cement-sand mortar will cost less.

Technology for plastering door slopes:

Surface preparation. Since this is a dirty job, you need to cover the door leaf, floor and nearby objects with film or tape. After this, poorly adhering plaster, brick or other materials are removed from the surface. To obtain a high-quality result, it is recommended to completely remove all old plaster. The gaps around the door frame are filled with foam. After it dries, the excess is cut off with a sharp knife.
All remnants of old materials are removed from the surface of the slopes, after covering the door leaf with film
Setting up guides. In order to get a flat surface, it is necessary to set the guides. A perforated corner is installed outside the doorway, fixing it with a solution. The role of the second guide will be performed by the door frame. The plaster should not completely cover it, so a template is made from wood or thick plastic to level the solution. If the work is done with a spatula or a rule, then it will be necessary to set beacons.
Using a template, level the layer of applied plaster
Rough plaster. In order for the solution to adhere well to the surface, it must be cleaned of dust and primed. You don’t have to use a primer; then the surface is slightly moistened with water before applying the plaster. Using a spatula or a paint bucket, apply the mortar onto the wall, and then level it with a rule or template. At this stage, you should not achieve special evenness, but you need to monitor the condition of the corners and remove excess mortar. The upper slope is more difficult to deal with, but this work can be done independently.
When applying rough plaster, it is not necessary to achieve a particularly even surface.
Finish plaster. The first layer should dry within 12–16 hours. To determine the readiness of the surface, you need to try the coating by touch - it should not float, but crumble. For finishing application, a more liquid solution is prepared compared to what was used for rough plaster. It is thrown on and leveled well. To get the most even surface possible, the rule must be moved along a zigzag path.
To obtain the most even surface possible, the rule must be moved along a zigzag path.
Grout. At this stage, the maximum level surface is achieved. You can begin work only after 16–24 hours, when the plaster is completely dry. Make a fairly liquid solution and distribute it not with a spatula or template, but with a special grater. The work is performed in a circular motion. If you plan to putty the slopes, then this step can be skipped.
If the surface will be puttyed, then grouting of the plaster may not be necessary.
Finishing. It is recommended to prime the surface again and then putty it. First a layer is applied starting putty, and when it dries (this will take 4–8 hours), the finishing composition is applied. After it dries, the surface is leveled using a special mesh, eliminating all, even the most minor, irregularities.
After puttying the slopes, they are leveled, achieving a perfectly flat surface.

If plastering slopes is done independently and for the first time, then you may not immediately get a perfectly flat surface for painting, but even a beginner can prepare a slope for wallpapering.

Video: plastering door slopes

Sometimes interior doors are not installed, but you still need to create slopes in such an opening. The technology for performing the work is similar to that described above, the only differences will be in the method of installing the guides:

Nuances of installing door slopes

Thanks to the existing variety of materials, owners have the opportunity to experiment and choose the one that perfectly matches the interior of the room. It is necessary to take into account the purpose of the door, since it can be an entrance or an interior one. In addition, before choosing a material for finishing slopes, you should evaluate your capabilities, since some installation options require special skills.

Expert advice:

To obtain a high-quality and beautifully designed slope, you must strictly adhere to the technology of performing the work, which will be different for each material. If you skip at least one of the stages or do it incorrectly, the result will be ugly and the materials will be damaged.

Creating door slopes is an ideal option for completing the finishing of any opening - including external and interior doors. These works are as important a stage of repair as the process of installing the canvas itself. And the final picture, which can affect the entire interior of the room, largely depends on their quality. In order to install door slopes with your own hands, you must have certain skills, as well as decide on the implementation method and materials of construction.

Classification of structures

There are several options for how to make a door slope with your own hands, which involve using:

drywall, suitable for finishing surfaces whose leveling will require a large amount of solution. With the help of plasterboard sheets, the surface is easily leveled and, at the request of the artist or customer, painted or plastered;
plaster, used in cases where the surface can be leveled using a layer of mortar no more than 30 mm thick. This option is not the fastest, but it is profitable and simple;
laminate, which is suitable for doors or arches already finished with this material. Finishing door slopes laminated chipboard not suitable for rooms with high humidity and, even more so, for external doors;
MDF panels, resistant to both temperature changes and high humidity, making it suitable for any door;
tree, a material that is not cheap, but has good aesthetic and strength characteristics. For finishing the slope of a doorway when performing repair work various classes(economy, standard or exclusive) both regular wood and valuable species tree.

Choosing the option with door slopes with your own hands, decorative stones or tiles is a rare option, but it also has a right to exist. It is used mainly for the entrance doors of mansions. Decorative stone looks especially advantageous in combination with a porch, terrace or path to the house made of the same material.

The variety of ways to finish door slopes allows you to choose the appropriate option for any conditions. One of the main selection criteria is compliance decorative characteristics designs general interior. If several options are suitable for the design of the room, choose the one that most suits the tastes and financial capabilities of the home owner.

DIY door slopes

During the installation process, it is necessary to prepare the surface. And only then apply the chosen finishing technique. And it, first of all, depends on what kind of doors we are talking about - those installed between rooms or entrance ones.

Slope preparation

In most cases, the surface is pre-leveled. To do this, the contractor must first prepare necessary materials– plaster, primer, starting putty, construction mixer (or a suitable drill attachment), roller, mesh, masking tape and bucket. In addition, to prepare for finishing, the slope must first be completely cleared of old finishing materials(type polyurethane foam or plaster) and dirt. And then move on to the alignment steps, which can be found on the Internet and even watch a video of this process:

Prime the surface;
in a suitable container;
Apply the solution, leveling it until required thickness. The adhesion of the material can be improved by spraying the concrete with water. And, if the wall was severely damaged when installing the door, a special mesh should be used;
using corners;
Rub the dried layer of mortar until cracks and irregularities disappear;
Re-prime;
Bring the surface to normal condition using already
Having leveled the surface, proceed to the final finishing - painting (if the simplest option is chosen), wallpapering, laying tiles, installing drywall or panels.

Slopes for entrance doors

If we consider options suitable for external doors, it is worth noting the three best, which have a sufficient margin of strength and can withstand constant closing vibrations. Internal slopes finished with laminated chipboard or MDF. The panels are installed using polyurethane foam, liquid nails or using guide bars.

The exterior decoration of the door is most often done using plaster, onto which tiles or stone can be attached. The beginning of installation does not differ from leveling the surface, but ends with fixing the finishing material with glue. If additional finishing is not expected, the plaster is painted.

Slopes for doors between rooms

Do-it-yourself work on finishing the slopes of interior doors can be done using almost any materials. The main thing is to maintain consistency between the styles of structures facing the same room. MDF slopes look good in a living room - especially if you match them to the tone of the interior. Slopes covered with wallpaper are also suitable for decoration; they visually extend the walls and increase the size of the room.

Used in bathrooms ceramic tiles- again the same one that was laid on the walls. Ceramics are glued to a leveled surface. If the room is finished with plastic or metal-plastic panels, you should choose the same materials for the slopes. The same applies to rooms whose enclosing structures are finished with plasterboard.

Among the options suitable for interior door slopes, panel and plasterboard structures. In addition to the fact that they look more profitable, the cost of such a design will be more favorable than for options made of wood and tiles. And the time required for repair work is shorter compared to

Paneling

The method for making door slopes from MDF panels is suitable for any door and involves installing a wooden frame, the slats for which are purchased in advance and treated with an antiseptic. In the process of choosing a material, the main thing is not to make a mistake with the dimensions. It should be taken into account that the thickness of each strip in the process increases by the size of the plate attached to it;

Panel finishing begins with the selection necessary tools and materials:

panels used for finishing;
wooden blocks;
self-tapping screws;
screwdriver;
roulette and level;
hacksaws.

The technology for finishing the slopes of interior doors with your own hands from MDF is as follows:

Removing peeling paint and old plaster;
Surface primer, which does not need to be leveled;
Fastening the frame from bars at a level with leveling distortions on the walls (using boards or pieces of plywood);
Pad mineral insulation(especially relevant for external doors);
Cutting panels to fit the slopes to be finished, fitting or fitting.

The final stage of work is to secure the material to the frame. If self-tapping screws are used for fastening, they are screwed in slightly deeper into the material and. Although when installing MDF panels, liquid nails are most often used, which are applied pointwise to the guides.

Approximately the same technique is also suitable for installing laminate as finishing slopes for interior doors. Work begins with securing the bottom board with self-tapping screws and securing the next three boards with a lock. The fifth board is also installed using fasteners or liquid nails, after which the frequency continues. For a horizontal slope, each plank is fixed. The corners between walls and slopes are finished decorative corners or platbands.

Plasterboard structures

The option of installing slopes for interior doors made of plasterboard sheets is suitable if the enclosing structures of the room are finished with the same material, and leveling the surface using only putty will require a significant amount of material. The choice of the two possible options is influenced, first of all, by the length and width of the slope.

So, for small installation seams and minimal damage when installing the door, the first method is used:

From plasterboard sheet elements are cut taking into account the slope angle;
The surface of the slopes is cleaned and primed;
The dry mixture for gluing drywall is diluted with water according to the instructions;
The finished substance is applied in a thin continuous layer to the element that needs to be pressed against the prepared slope;
The panels are installed starting from the side surfaces;
After installation, the cut parts are fixed using masking tape.

The glue dries, after which the seams need to be puttied and cleaned with fine-grained sandpaper. And after another layer of primer is applied to the slope, it is considered completely ready. Additional finishing can be installed on top of the drywall.

After installing a new iron entrance door in the apartment, everything pleasant impression it can immediately disappear if slopes are not made from inside the apartment. Only they can say that the stage of repair work is completely completed.

To make them perfect, specialists are most often invited. On the other hand, you can do them yourself if you first study all the tips and recommendations.

What are door slopes?

Slopes are a small section of the wall located around the door frame (outside and inside it).

IN last years their arrangement is mandatory because they not only decorate the overall appearance door space, but also serve as the beginning of the overall design of the corridor or rooms.

Types of finishing materials

By selecting the right material, we can safely say that success awaits you in the process of finishing the slopes. If you are a beginner builder or do not have a lot of time and money, do not take on methods that require really significant skills and experience.

To avoid mistakes, you need to know what materials suitable for creating a beautiful space around the front door.

MDF panels

MDF panels are a popular material that is perfect for these purposes. As a result variety of colors, panels can be used to decorate slopes in almost any interior.

Installation occurs using regular or liquid nails, as well as self-tapping screws, corners or casing are applied around the perimeter.

Among positive properties The following should be noted:

able to withstand small impacts and damage;
have an attractive appearance;
easy to install by one person, do not require professional help;
remind oneself various breeds wood, which allows you to make the appearance of the slopes visually expensive and sophisticated;
have good noise insulation properties.

The disadvantages of the panels are that they cannot withstand scratches and strong impacts, as well as can change their appearance and structure, if they are installed in rooms with high humidity (for example, baths and saunas).

In addition, being exposed various pollution, require careful care, otherwise it will be almost impossible to wash them.

Decorative stone tiles attached to a special solution. Interior decoration decorative tiles looks interesting and expensive.

The advantages include:

has a lower cost than natural stone;
is light in weight;
does not require special care;
thanks to the wide color scheme can imitate the appearance of any stone;
able to withstand significant temperature fluctuations;
resistant to moisture.

Main The disadvantage is the fragility of the material. In rare cases, the size of the opening will coincide with the size of the tile, so its installation almost always requires the ability to correctly and accurately cut the tile to avoid cracking.

If you choose a heavy tile, there is a possibility that it will lag on the upper part of the slope, creating danger for human life and health.

Laminate

Another option for finishing door slopes is laminate, a material has the following advantages:

good indicator of strength;
shelf life can be up to 15 years;
a wide selection of colors allows you to choose the one that suits each specific room;
have excellent thermal insulation characteristics;
easy to wash and clean from various contaminants;
can be easily attached to them decorative elements(using regular glue).

Among the disadvantages, it can be noted that this type of finishing material poorly resistant to moisture and temperature changes. As a result, over time it may change its appearance and initial technical characteristics.

If you plan to install laminate flooring on a frame, then you need to be prepared for the fact that the doorway will become smaller.

You might be interested to know about plastic panels for walls, their types and sizes. Read this one.

Plastic

Plastic trim is well suited for a doorway only because you don’t need to spend a lot of money to purchase it, it is lightweight, can imitate various textures and materials, and is also easy to care for.

One of the disadvantages that can be noted is its fragility, because even with the slightest impact and effort, it simply deforms and breaks.

Decorative rock

Decorative stone is a material with a huge number of positive properties. Decorative stone finishing quite expensive compared to other materials, but also looks more luxurious in the interior, as shown in the photo.

Advantages:

completely environmentally friendly material;
installation does not require a perfectly flat surface;
stand up well high temperatures, a large amount of moisture;
unlike natural stone, it has significantly less weight;
wonderful appearance, variety of textures allows you to satisfy the tastes and requirements of any buyer;
can be mounted in a doorway of any shape and size;
does not burn, retains heat well in the room;
It washes well and does not absorb foreign odors.

Of the minuses decorative stone all that is known is that it is not recommended to use it for exterior finishing doors, which immediately go out onto the street.

When exposed to very low temperatures and severe frosts, the material may deteriorate slightly.

Plaster

Plaster is often used to create doorways. This is one of economical options finishing, with the help of plaster, if necessary, you can not only seal the slopes but also level them.

It has the following advantages:

perfectly insulates living space;
cleans well from dirt;
has high strength;
thanks to in various ways applied to the surface, you can give the slopes a unique appearance;
long shelf life.

Main stages of drywall installation:

Having measured the size of the side slope, cut a blank from a sheet of plasterboard, which must necessarily be 1 cm larger in width. If this is not done, then the sheet will not be able to be inserted into the gap between the opening and the box.
Having made a recess with a knife in the mounting foam passing between the door frame and the opening, insert the side cut sheet into it. Slightly bending it on the other side, use a gun to apply polyurethane foam along the entire length.
Press the material well against the wall. Make sure there are no distortions. The sheet must be positioned strictly vertically. Fill all cracks with foam.
Carrying out all the above steps, secure the second vertical slope in the same way.
Measure the top of the opening and from a sheet of drywall cut a sheet of identical length, which will be 1 cm larger in width (for the same purposes as the side sections).
Make a recess in the polyurethane foam into which to place the resulting piece of material. Use a level to check the correct angles between the side and upper sections of the slope.
Glue the sheet with foam, pressing it well to the base of the wall.
Wait until the polyurethane foam has completely dried(this will take 1 day) you can start applying finishing materials to the drywall.

This video shows step by step how to finish the slopes with your own hands.

How to apply?

Design of slopes – an important stage in the entire work of creating a doorway. You need to start by creating corners on the drywall using putty.

This should be done this way:

Using a spatula, apply a small layer of putty to the corner.
After waiting for it to dry completely, we apply serpyanka, which is covered with another layer of putty.
When the second layer is completely dry, apply thinly to the corners. finishing putty. In this case, any unevenness must be avoided.

If you plan to paint such slopes, then the entire surface of the drywall must also be plastered twice. In the event that you complete renovation work There will be wallpaper, the sheets do not need to be further processed.

Creating beautiful door slopes - not very hard work which any man can do, without resorting to outside help. The main thing is to study everything first necessary recommendations, consult with a specialist and purchase those materials that will be simple and easy to work with.