DIY lampshade: master class on creating an original design for lamps (80 photo ideas). How to make a lampshade with your own hands: making a lampshade for a lamp at home Paper fragments for chandeliers and lamps

Do you dream of adding brightness to the nursery or refreshing your workplace in the house? Or maybe you are a lover of the East, where the fashion for these such delicate little things came to us from? Then you should definitely read how to make a lamp out of paper with your own hands - unusual, original little things will instantly add a bit of magic to any corner of the house!

We guarantee that your guests will be asking for a long time where you bought this designer lamp, and having learned that you made it yourself, they will ask you to tell you how to make a paper chandelier with your own hands and its step-by-step instructions.

In this master class we will show you four ways to make a lamp out of paper, take a look and choose the option that’s right for you.

To create this delicate lamp, prepare:

• Colored paper of any color;
• PVA glue or glue stick;
• Paper clips;
• Compass;
• Scissors;
• Fishing line;
• Colored yarn;
• LED lamp ( );
• Wire with switch.

Step-by-step instruction:

Step 1

• Using a compass, draw semicircles 1 cm wide on a colored sheet of paper.
• With each line we increase the diameter of the semicircle.
• Please note that you will need quite a lot of sheets. Then cut out semicircular strips and cut them into pieces of 2-5 cm.

Step 2

• Roll and glue the resulting strips, making one side larger than the other - this will make it easy to glue them together into a dome-shaped shape. After that, you can connect them with glue in pieces of five.
• Glue the clusters together, strengthening them with paper clips until the glue dries. Glue until you have a circle, with a small hole for a lamp.

Of course, you can fantasize, and your lamp will be a little different than ours.

Step 3

Now, while our glue is finally drying, let's decorate our wire. To do this, take yarn of any color you like and carefully begin to rewind the wire with it. Try not to leave any uneven spots when wrapping the yarn over the previous layer.

You can add a drop of glue to the end of the yarn to strengthen it.

Step 4

Let's make a holder for an LED lamp. To do this, we tie a fishing line on three sides (it is advisable to measure the distance evenly) to our glued strips, and the other ends to a paper clip, which we first straighten to the shape of a triangle.

All! All that remains is to place the lamp in the circle and screw it to the wire. You can hang such a lamp either separately or in combination with, for example, .

Master class No. 2: Chandelier made of rice or parchment paper

We present to your attention new master class, where we will teach you how to make lamps from rice paper. There is nothing complicated in making it, as it might seem at first glance, and you can involve all household members in this exciting activity. The designer lamp is suitable for both the nursery and your bedroom.

Instead of rice paper, you can buy a roll of parchment paper for baking

So, to make a lamp you will need:

• Unnecessary lampshade;
• Thin wire;
• Several rolls of rice paper;
• Iron;
• Paper cutter;
• Sewing machine.

Self-production

Step 1

Take a lampshade you don't need (you can buy inexpensive new) and remove everything from it, leaving only the base. If your lampshade is similar to ours, then add a wire in the middle, securing it well.

Step 2

1. Prepare the parchment paper by unrolling the rolls and cutting them into roughly equal rectangles.
2. Iron the sheets until they become completely even and smooth.
3. Fold each sheet like an accordion, measuring equal distances of strips, and use a paper cutter to cut equal, even circles.
4. Try to use the cutter more carefully and don't leave a lot of extra paper– you will need a lot of circles.

Step 3

1. Connect all the circles together by stitching in the middle. Make connected circles of equal length and begin to strengthen them around the circle of the lampshade.
2. Once you complete the first circle, go around the subsequent ones, decreasing the length each time.
3. Carefully secure your lamp in the desired location, straightening all the threads.

Remember to use only LED lamps to avoid fire.

This beautiful chandelier is the result painstaking work, after completion of which you will admire your work and be proud of yourself for a long time. On our website you will find many more ways to diversify your home lighting, for example:

• you can or .
• , for lovers of modernism.
• Or for lovers of eco-style.

You can also at your discretion, paint the rice paper circles in any shade, based color range rooms. If you want to hang this lamp in a child's room, you can add, for example, glass angels on long gold threads - again, choose the right accessories for your child's room. different rooms, this will add warmth and originality.

WARNING: Be aware that incandescent lamps produce very hot temperatures and may cause paper to ignite. For paper lamps and lamps, use only LED lamps.

Master class No. 3: Origami chandelier made of paper

This beautiful bright lamp really resembles a ripe berry!

To make it, take the following:

• 2 paper bags, so that when gluing you get a one and a half meter bag (preferably with an interesting print);
• LED lamp (never an incandescent lamp );
• Wire with switch;

As soon as you decide that training is no longer necessary, we begin preparing the paper bag. Remove the handles and cut the bottoms off the bags and glue them together to make one large paper bag.

Fold the resulting bag in half, and then fold the halves like an accordion so that you get 16 identical folded strips. Then fold the two outer strips diagonally.

Follow the simple diagrams and you will get wonderful lamps to decorate your home. You may have to practice a little to fold origami perfectly, but you won’t regret it, because origami is a whole world of various interesting things created with your own hands. And your children will simply be amazed by your skillful hands!

Master class No. 4: Corrugated paper lamp

To make an unusual lamp you will need:

• Corrugated paper 88×44cm;
• Ruler;
• Spoke;
• Glue;
• A thread;
• Cable;
• LED lamp ( never an incandescent lamp ).

Step 1

• Using a ruler, mark a sheet of paper at equal intervals and fold like an accordion according to the markings.
• Helping yourself with a knitting needle, fold the folded sheet of paper diagonally, first on one side, and then unfold it on the other side.
• Unfold the sheet - you should have it double sheet marked with diamonds.

Step 2

• Connect the marked lines according to the photograph; it is advisable that the sheet is not very wrinkled at this time - otherwise appearance the lamp will be damaged.
• All that remains is to connect the top of the lamp with a thread so that it does not fall apart, and secure the cable with the LED lamp.

Be safe - do not use regular incandescent lamps, they heat up the paper and it may catch fire.

Paper butterfly chandeliers

The most popular paper chandelier is the butterfly chandelier. And such love for this product is not just:

• Firstly she looks very chic and expensive.
• And secondly The production is very simple, even a child can be involved.

Such an elegant lamp will go well with any interior style, and it is also appropriate in the living room or dining room and even in a children's room.

Manufacturing technique:

1. It is taken as a basis old chandelier or a frame from it. If this is not the case, then you can take a regular metal or wooden rim. If there is no such thing, take a thick wire and make 2-3 coils of yourself, so that you get a circle.
2. Cut out butterflies according to the template (butterfly template below)
3. We take a nylon thread or fishing line and attach butterflies to it. There can be two types of fastenings: either we pierce the butterflies or we put them on silicone glue. Whichever is more convenient for someone.

Butterfly pattern

To make a chandelier with butterflies, simply take a template and scale it to your size. It looks very nice if you make butterflies of several sizes, for example 3-4 diameters. Using a pencil, draw the sketch on paper and cut it out.

• It is best to cut with stationeryknife or straight manicure scissors without curves.
• It's better to use paper more dense and which does not attract dust, for example velvet structure. Since you will have to vacuum such a chandelier often

Also a very beautiful option is obtained if you make a ball out of wire, take as a basis an old pendant from a chandelier and place it using glue gun several butterflies.

Paper ball chandelier

The basis for such chandeliers is a ready-made Chinese lamp made from a ball of rice paper. They are usually very cheap, down to 1-2 dollars. But you can decorate it however you like with paper tartlets, an unnecessary map, newspaper or sheets of old books. We are publishing several ideas for decorating a ball chandelier with paper.

Paper New Year lamp

A regular idea for the New Year is to use an old lampshade and string snowflakes of various shapes onto a string. Very impressive and beautiful. Below are a few photo ideas such decor for the new year.

To polish your skills, as well as to replenish your collection with extraordinary beautiful lamps, see more ideas and . We are sure that among them you will find many that you will definitely want to create!

2 ratings, average: 5,00 out of 5)

Lighting can either transform or make any room uncomfortable. Suffice it to recall cold hospital corridors, and, for example, cafes, where there is always soft warm light.

Especially in winter, people miss the sun, so it is very important that there is always light at home. A special cozy atmosphere can be created with the help of various lamps or floor lamps. However, it is not always possible to choose a lamp that matches the interior of the room. But don’t be upset, because you can do it for any lamp.

DIY frame and base for lampshade

First you need to select a lamp or several lamps for which you need to make fabric lampshades. It is better to use lamps with energy-saving or LED lamps. Regular light bulbs can simply burn the fabric, so it’s better not to take risks.

Before you begin, you need to remove the frame for which the lampshade will be created. If the lamp does not have a frame, then it can be purchased, for example, in a special store or construction department.

Also, the frame for any lamp, be it a floor lamp, table lamp or chandelier, can be made independently. To do this you will need thick wire and pliers.

The base can have any shape. It will be easier to make a lampshade for a cylindrical or cone-shaped frame.

How to choose fabric for a lampshade

First of all, you need to choose a suitable fabric for the lampshade. You can use light, hard or dense material. If desired, you can even make a lampshade from wool, it all depends on the creator’s idea and the interior of the room.

If the frame consists of ordinary wire, it is better to use an opaque material to cover it. Dark silk, cotton and taffeta are suitable.

It is also worth remembering that the color of the fabric can give both cold light, and warm. In the first case, you can use blue or green fabric, and in the second, yellow, orange or red.

Necessary materials for making a lampshade

Fabric lampshades can be done different ways. If the new lampshade is glued on top of a regular plain lampshade, then there will be no preparatory work not required.

But if there is only a wire frame, then it is better to first coat it with paint and then wrap it with light or dark cotton tape.

To make the lampshade look neat, you need to sew it on a typewriter.

In addition, you will need:

• iron;
• a simple pencil;
• ruler;
• textile;
• pins;
• threads matching the color of the material;
• kraft paper (or any thick paper, as well as whatman paper);
• glue (you can take a special one for fabric or a universal one).

When all necessary materials and the tools are at hand, you can start sewing DIY lampshade made of fabric.

Master class on making a lampshade with your own hands

First step

First you need to make a template to cut required amount fabrics.

There are two ways: if the frame is cylindrical, then you can measure the circumference and draw one line on the fabric, and then measure the height and draw a second line. After this, all that remains is to draw two more sides of the rectangle and cut out the template.

If the frame is cone-shaped, then you can lay out the paper, take a pencil and gradually roll the frame along the sheet, mark with a dotted line the lines of its sides.

The main thing is that the frame rotates completely; to do this, you can mark a reference point on it using a piece of thread or a pin. After this, you can connect the lines and cut out the template.

Second step

In order not to cut off more, or worse, less fabric, you need to attach the template to the frame of the lamp - it must completely fit. If the template is larger, you need to cut off the excess paper; if it is smaller, you will have to take the measurements again and make a new template.

Third step

When the size of the template matches the size of the base for the lampshade, you can begin to attach it to the fabric. If the material has a pattern, you need to position the template so that the drawn elements “look” in the right direction. You need to calculate everything so that, for example, you don’t cut off the head of a flying bird. Otherwise the lamp will look ugly.

The template must be applied to the wrong side of the fabric, and then it must be secured with pins. After this, you can carefully trace the template along the contour. If the fabric is dark in color, you can use not a simple pencil, but special fabric crayons or a piece of soap.

After this, you need to draw allowances. To do this, you need to draw lines at a distance of one and a half to two centimeters from the boundaries of the template.

Fourth step

Without removing the template from the fabric, you need to carefully remove the pins one at a time and wrap the seam allowances inside. The fold lines must be secured with pins.

Now you need to remove the template and fill sewing machine. The threads must be chosen so that they are almost invisible on the fabric.

Fifth step

Now you need to sew the resulting part on a typewriter. This needs to be done only on three sides - one of the sides must be left untreated in order to then form a seam on the frame itself.

You need to stitch at a distance of five to seven millimeters from the edge. If desired, you can process the sections. But in any case, they will have to be hidden when the fabric is glued to the frame.

Sixth step

After this, you need to turn on the iron and iron the fabric piece well. If wrinkled parts remain, the fabric will not adhere well to the base, and the lampshade will look ugly.

Seventh step

The next part of the work must be carried out in a well-ventilated room. First you need to lay work surface waste paper or an old tablecloth and lay out the fabric. Then you need to apply glue to it and leave it for some time, which is indicated in the instructions for the glue.

Eighth step

Now you can glue the fabric to the frame. You need to hide the raw cuts, and make the seam in such a way that the lampshade is covered with a stitched edge.

If the lampshade is attached to a wire base that is wrapped with cotton ribbons, there is no need to apply glue to the entire surface of the workpiece; it is enough only to the part that comes into contact with the frame parts. In this case, you need to stretch the fabric well.

Ninth step

The finished lampshade must be left for some time to dry completely. After about a day, you can put the lampshade on your favorite lamp and enjoy a beautiful object that will definitely decorate any interior.

Fabric lampshade decoration

Table lamp with lampshade looks much nicer than just a regular bare lamp. But if a monochromatic color is chosen for the lampshade, then you can decorate it in an original way. Here are some ideas on how to do it interesting decoration fabric lampshade.

Lampshade in Provencal style

In order to decorate a plain lampshade, you will need a piece of fabric and fringe. Usually green, turquoise and pastel shades of colors are used, checkered colors or floral patterns are also suitable.

First, you need to select a suitable fabric for a plain lampshade and cut two strips from it - one to decorate the top of the lampshade. This strip of fabric should be long enough to completely wrap the circle and make a bow. The second strip should be the length of the circumference of the bottom of the lampshade, and fringe must be sewn to it. This can be done on a sewing machine.

All free edges of the fabric must be processed so that it does not fray. After this, using glue or thread with a needle, you need to attach the fringed ribbon to the base of the lampshade so that the fringe hangs down.

Then you need to decorate the top of the lampshade. To do this, you need to glue or also sew a ribbon along the circumference, and tie the free edges with a bow.

For lampshade in provencal style You can also use lace. The good thing about this element is that it can simply be glued to the fabric.

You can make lace flowers, stripes, or completely cover the fabric lampshade with lace napkins.

Lampshade with fabric flowers

Another one unusual idea which will allow table lamp with lampshade to become like a flowerbed - decorating with fabric flowers.

Great for flowers suitable fabric delicate shades, you can use, for example, organza or chiffon, or you can simply take, for example, an old jacket, cut strips and twist roses out of them.

You can decorate a lampshade with just a few flowers, but if you have time and patience, you can make a whole bunch of flowers to completely cover the lampshade.

DIY lampshade made from scraps

If you have many pieces of different fabric at home, you can make a lampshade from multi-colored scraps.

In order to make such a lampshade, you need to use the technique of sewing pieces to a fabric base. The easiest way is to cut a piece of fabric to the size of the frame and divide it into several wedges.

Then you need to sew patches to each wedge the way you like - you can sew strips of fabric diagonally, or make small squares. To avoid delaying the process, it is better to use a sewing machine.

After this, all the wedges with patches will need to be sewn together and glued to the base of the lampshade.

This lamp can fit perfectly into a country style!

Lampshade made of unusual materials

When you make a lampshade yourself, you can give free rein to your imagination and experiment. To do original item, you first need to find unusual material.

For example, in the kitchen, a lampshade made from burlap can look very interesting. This fabric transmits light well. Such a lampshade can be decorated with some wooden parts, for example, clothespins or wooden beads and buttons.

You can also use grandma's old lace doilies for decoration. You can also write something on such a lampshade with white or black paint, as they usually write on bags.

For a teenager's room, you can sew a lampshade in . For this you will need denim. And you don’t have to buy it, you can just cut up old jeans - every person probably has such a thing.

Such a lampshade can be decorated, for example, with a denim pocket where you can insert artificial flower or a piece of a checkered handkerchief. You can also use applique for such a lampshade. Pieces of leather are suitable for this.

For example, for a lamp that will stand in a girl’s room or bedroom, you can sew a delicate lampshade from mesh. This fabric can be found in any sewing store.

A lampshade made of several layers of mesh will look interesting - it will resemble a ballerina’s tutu or a fluffy skirt.

Those who have creative imagination and love free time decorating the house with things you made yourself have several advantages over others.

1. What is the advantage
2. From fabric
3. From paper
4. From threads
5. Other solutions

What is the advantage

• Opportunity to save money. A unique author's product will be obtained free of charge or a purchase will be required small quantity materials, which is several times less than the cost of a finished product purchased in a store.

• A way to express your individuality, to come up with and make extraordinary, unlike standard, interior items, for example, lampshades for chandeliers, with your own hands;

• Working together with young children will allow them to get involved in work, spend fruitful weekends together, and show their creativity.

• By putting your soul and positive energy into your creation, you can make a wonderful gift for your family; mothers and grandmothers will be especially happy about it, as it will become a pleasant reminder of their beloved children or grandchildren.

From fabric

Even those who have not learned the rules of sewing and do not have a home can decorate a chandelier with the rest of a beautiful fabric. sewing machine. It’s good if there is the same material in the house as on the upholstery upholstered furniture or curtains. Then the lamp will become part general finishing interior

A bright lamp will decorate the kitchen, country house, children's room. The technology for its manufacture is very simple. Thanks to it, it will have a neat appearance both from the outside and from the wrong side of the product. To work, you need to stock up on suitable fabric, scissors, double-sided tape, thread and a needle.

• Remove the old covering from the unnecessary chandelier, leaving the frame.

• Prepare even strips from the fabric of the future product. To do this, at regular intervals, approximately 3 - 5 cm, along the warp threads, make cuts and tear the fabric with quick movements.

• Then iron the strips and trim off excess threads, neatly shaping the edges. The length of the strips can vary, the longer the better because fewer connections will be required.

• Starting the process of forming the lampshade, one of the strips should be secured to the upper ring of the frame using a needle and thread.

• Gradually wind the fixed strip around the upper and lower rings of the frame, overlapping each subsequent layer with the previous one. When the first strip ends, sew the next one to it from the wrong side and continue.

• In order for the lamp to have a finished look, the lower and upper edges of the lampshade should be decorated. To do this, cut a strip 14 cm wide from contrasting fabric.

• Fold one edge 2 cm and iron.

  Apply double-sided tape to the inside.

• Then glue the finishing tape to the lampshade, gradually removing the protective layer from the tape, while simultaneously wrapping it on the inside.

• Similarly to the top, trim the bottom edge of the lampshade. Trim off the excess material.

Thus, with the help of this master class it is not at all difficult to update an old chandelier.

From paper

Another way to show your imagination and at the same time spend your free time profitably is the opportunity to make a lampshade out of paper.

To do this, you need to cut strips of white, colored paper, thin cardboard or plain newspaper. Then arrange them into a product by arranging the strips randomly, winding them symmetrically relative to the central part of the chandelier, as seen in the photo.

Periodically apply glue at the points of contact and form a stable structure.

From threads

Quite simple to make and effective in working order is a lampshade made of threads.

How to update a table lamp with your own hands: 37 ideas for a lampshade

The proposed instructions will tell you how to make an original lamp from scraps of colored yarn.

1. For work, prepare a rubber ball according to the desired size of the lamp, scissors, glue, thread.
2. Inflate the ball and wind the threads, crossing them in any direction, leaving free gaps.
3. When finished, apply clear glue to the surface.
4. Without waiting for complete drying, carefully cut a hole, which will later be necessary to screw in the lamp, deflate and pull out the ball.

Other solutions

People with out-of-the-box thinking, creative imagination will not throw away unnecessary things from which it is quite possible to build an original lamp. For example,

• from a plastic bottle and disposable spoons;

• from metal gears and parts;

Unique, original decoration premises and the surprise of guests from the exclusive lampshade will be ensured.

Read also: DIY wooden chandelier, Which lamps are better for suspended ceilings

A minimum of material and modest craftsmanship skills are all that is required to give a new look to an old table lamp.

The lampshade of your favorite lamp has faded and is no longer pleasing to the eye!

Replace it with a new one.

Ideas and master classes for making DIY lampshades for a floor lamp and table lamp

And it’s not at all difficult to make one by covering the fittings of an old lampshade with a fabric with a pattern you like or with a scrap of wallpaper left over after the renovation.

Using self-adhesive paper (with a protective film) to make a lampshade simplifies the “production” process. This paper is sold both in rolls and in the form of individual sheets.

If you don't have self-adhesive paper, you can use self-adhesive transparent film. It is especially effective for gluing the covering of a lampshade made of wallpaper.

To make a new lampshade, you will need: self-adhesive paper with a protective film, a steel ruler, covering material, tape for finishing the edges, adhesive tape, universal glue, frame rings, clothespins.

How to make a lampshade pattern

The dimensions of the lampshade are determined by the diameters of the large and small rings of the frame. Marking the pattern for covering is done like this. First, on a sheet of plain paper of a suitable format, draw a segment AB, the length of which is equal to the diameter of the lower ring. From the center Z of this segment, a perpendicular is restored and point Y is marked on it - the height of the future lampshade. It is chosen at will. Next, through point Y, a segment CD equal to the diameter of the upper ring is drawn parallel to AB.

The pattern of the covering should have the shape of a ring segment. To find its center, segments AC and BD are extended. The point of their intersection will be the desired center X. From it, through points A and C, arcs of concentric circles are drawn with a compass.

The segments EG and HF that limit the segment are the joining edges of the pattern. Their position is found as follows: the length of the segment AB is divided by the length of the segment AX, the quotient of the division is multiplied by 180 degrees. The resulting angle is laid off from the X center, halved relative to the XZ axis.

How to assemble a lampshade

Depending on the design of the lamp, the lampshade is attached to it using the lower or upper ring. To do this, the corresponding ring of the lampshade is connected by knitting needles to a sleeve placed on the socket of the socket.

Our lampshade does not have parts that fasten the rings together and determine their relative position. This function is performed by the tight fitting. Therefore, the rings must be attached exactly to its edges parallel to each other. The slightest inaccuracy and the lampshade will become skewed. To prevent this from happening, before finally assembling the lampshade, the rings must be carefully tried on.

	1. Wrap the ring with adhesive tape, sticky side out, so that its surface is as flat and smooth as possible without wrinkles.
	2. Delete protective film from self-adhesive paper and stick it on the fabric. Press the fabric onto the paper.
	3. Place the pattern on the fabric, align the edge and cut out the lampshade cover along the contours.
	4. Roll the blank into a lampshade, insert and secure the lower (larger) ring with clothespins. Glue the edges of the workpiece from the inside.
	5. Glue the bottom ring and compress the adhesive joint with clothespins until the glue dries. The same is done with the small (upper) ring.
	Additionally, secure the adhesive seam from the inside with adhesive tape. The upper and lower edges of the lampshade can be decorated with braid.

Next page: Hot water bottle for a teapot... Do-it-yourself Rainbow doll Previous page: DIY piggy bank “Little Housekeeper”

Today I will show you how you can breathe into old things new life. We will talk about the Soviet floor lamp. In truth, even in its best years it was completely ordinary and unremarkable lighting fixture.

How to restore an old floor lamp with your own hands

Of course, we could just cover it with white paint, but we are not looking for easy ways. We will change the design of the item radically. So, to restore the floor lamp we need:

1. gold acrylic paint in a can;
2. polymer glue (I used DRAGON);
3. brush;
4. satin and gold braid (they can be purchased in stores specializing in the sale of fabric and sewing accessories);
5. threads in the color of satin and a needle;
6. gold acrylic paint for painting on fabric. They are made on the basis of aqueous acrylic dispersion, so they do not stink either during painting or after drying. I recommend using Javana (Germany) or Decola (St. Petersburg) paints. Read the instructions carefully and follow all safety precautions during operation.

As a result, I spent $10 on materials for restoring the floor lamp. In my opinion it is much cheaper than buying a new one.

With a floor lamp leg everything is simple. Spray paint from a can in 2-3 layers.

How to make a lampshade with your own hands from fabric

In order for the paint to dry thoroughly and not drip down, we take a break before applying each new layer for 15-20 minutes. Do not bring the can closer to the base of the floor lamp than 30 cm, otherwise the paint will lie unevenly. It is better to do this work on the street or balcony, because the smell from the paint until it dries will be sharp and unpleasant.

Then everything is a little more complicated. We lay out the satin on the floor and place the lampshade on it sideways in the center. We carefully roll it first in one direction and then in the other, while at the same time we outline the outline of the future product. I did it with chalk because... the fabric was dark, you could use a pencil. Cut out the resulting shape, leaving an allowance of 2 cm on each side.

Next we start painting. The pattern can also be pre-applied with a pencil or chalk. It is unlikely that you will be able to completely cover the color and texture of the fabric the first time, so you will most likely have to apply the paint in 2 layers.

Well final stage restoration of a floor lamp - assembly of the product. New fabric lampshade you need to sew the needle with the seam forward and put it on the old base, it is better to secure it at the top and bottom with polymer glue. We carefully sew the braid on top. Attach the lampshade to the base. That's it, our restored floor lamp is ready.

You can skip reading the entries and leave a comment. Posting links is prohibited.

How to make a lampshade with your own hands and a frame for it - for a floor lamp, beautiful made of paper + interesting video

1. How to do beautiful lampshade do it yourself from paper
2. How to make a lampshade for a floor lamp with your own hands
3. What can a lampshade be made from?
4. How to make a lampshade frame with your own hands

Fortunately, you don't have to buy a lamp just because of a beautiful lampshade, as you can make one yourself.

Yes, one that will cost less than buying a floor lamp, and at the same time it will be much more beautiful. And now Infosborka.ru will teach you how.

How to make a beautiful lampshade with your own hands from paper that can be used as a lamp

You will need

• Long stem glass
• Candle
• Rope - can be made from threads
• Drawstring with a tassel at the end
• Decorative tape
• Scotch
• Scissors
• Transparent paper with decorative pattern
• A little sand

Manufacturing process:

1. Make a template from plain A4 paper.

2. Attach the template to the transparent decorative paper with a drawing and trace it with a pencil. Then cut out the resulting image.

3. Glue decorative tape to the edge of the paper.

4. Secure the rope with a tassel at the end with tape on the back side of the paper.

5. Glue the side ends of the paper together.

6. Tie a string to the stem of the glass.

7. Wrap it around the leg as shown in the picture below.

8. Pour sand into a glass, place a candle on top and light it.

9. Place the dome you made on the glass.

And the lampshade with the lamp turned out so beautiful.

How to make a lampshade for a floor lamp with your own hands

You will need

• Patterned paper
• Decorative paper
• An awl with which you will pierce holes on the future lampshade
• Glue and brush
• Scotch
• Ribbon to match the color of decorative paper
• Clamps
• Frame for lampshade

In our case, the frame for the lampshade consists of two parts:

Manufacturing process

1. Tape the patterned paper to the back of the decorative paper.

2. Use an awl to make holes along the contour of the design.

Handicrafts for home

In the end it turns out like this:

3. Wrap the paper around the first part of the frame.

4. Mark with a pencil the line along which you will glue the decorative paper.

5. Glue the paper with glue.

6. Coat the bottom part of the resulting cylinder with glue and glue the second part of the frame to it.

To make it stick, press it with clamps.

In the same way, glue the first part of the frame to the top of the lampshade.

9. Glue the tape to the top of the lampshade. This is done like this:

• coat a small piece (about five centimeters)
• glue and clamp with clamps
• then coat it with glue and glue the next piece, etc., until you have glued the entire tape

10. Bend the tape so that it covers the frame and glue it.

As a result, you will get this lampshade for the floor lamp:

Using this technology, you can make any drawing.

What can a lampshade be made from?

• Beaded lampshade
• Lampshade made from plastic bottles
• Wicker lampshade in Provence style
• Lampshade made of organza or thread - you can make a hanging version

We will tell you how to make them in the following materials, but now I would like to tell you about...

How to make a lampshade frame with your own hands

You will need

• Welding wire - select the length 3, focusing on the height of the lampshade. At the same time, do not forget to add 3-4 cm for connection.
• The top part is from a jar of vitamins, the neck of which fits right into the lampshade.
• Vacuum cleaner cord return spring.
• Soldering iron.
• An object that can be used to poke holes (an awl, a nail, etc.)
• Pliers

Manufacturing process

1. Make a circle of the required diameter from the return spring of the vacuum cleaner cord. Solder the ends.
2. Make three holes in the neck of the vitamin jar and in the circle you made. The holes on each item should be approximately the same distance from each other.
3. Insert welding wires into the holes and bend their ends with pliers so that they do not come loose.

In the end, this is what you should get:

To relax a little after learning the information, here is a video on how to make a candle from an incandescent light bulb:

Don't switch. Soon there will be a continuation of the DIY lampshade theme. Using these links you can switch to the second and third parts of the article.

Making something with your own hands and then decorating your home is not a source of special pride? Homemade items allow you to unleash your creative potential and save a lot of money at the same time. AND self-production lamps are no exception. Today you can find various ways How to make a lighting device with your own hands. To do this, just type into the search bar “how to make a paper lamp with your own hands.” But you no longer need to do this, because in this article we will try to give the most complete answer to this question. Here we will touch on the most pliable material for a lamp - paper.

Our article will also help you understand whether you can cope with such work, and whether a paper lamp will suit your interior.

Paper - what could be simpler?

Light from a paper lamp

Lightness and airiness are what many associate paper with. Therefore, the paper lamp will also take on these properties, bringing with it to various interiors:

• unusualness;
• softening and smoothing out angularity;
• creating diffused and subdued light, giving the atmosphere romance and mystery.

Today, paper lighting fixtures are associated with Asia and the East. It was here that not only paper, but also products made from it first appeared: umbrellas, lanterns, etc. The East, as they say, is a delicate matter. This statement is perfectly brought to life with the help of paper and creativity, which is reborn into unique and unique lamps.
Despite the fact that China is considered the birthplace of paper, paper lighting fixtures can be safely made in different styles:

• Japanese;
• Chinese;
• pop art;
• eclecticism;
• country;
• vintage, etc.

Note! Only by making a lamp with your own hands will you be able to perfectly match it with the rest of the interior, emphasizing or connecting together all the directions of the design used.

Since working with paper is quite easy, and you can find it in almost unlimited quantities in the house, today there are a wide variety of options for assembling paper lamps. Let's look at the simplest and most popular of them.

Since paper was first made in China, it is logical to start with the creation of a lighting device in chinese style.

Chinese style lamp

Many people prefer to make lamps from paper in the Chinese style, since in this case they can bring brightness, vibrant colors and a sense of celebration to the interior. All this can be achieved with a Chinese lamp.
Materials you will need:

• paper. It can be rice or regular. It is desirable that the sheets of paper be translucent, colored or white;

Note! For the closest possible resemblance to the original Chinese folk lamps, you should work with rice paper.

• cartridge. It can be bought at the market or taken from an old chandelier;
• bulb. Since the lamp will be made of paper, unheated light bulbs should be chosen as a light source. It is best to opt for LED bulbs.

In addition to the materials themselves, you will also need some tools:

Chinese lantern diagram

• pencil and ruler;
• stationery knife;
• awl;
• a thread.

The lamp assembly will proceed as follows:

• make markings on back side paper. This way you can create a relief. To do chinese lantern, you need a diagram according to which the markings are made;
• bend the paper according to the markings so that in the right places receive accordion. Do not rush in this matter, since how smooth and beautiful the flashlight will turn out will depend on the accuracy of execution;
• we assemble the socket and the light bulb together;
• Make holes in the bottom with an awl and thread a thread through it;
• We wrap our paper lampshade around the socket. The edges of the paper sheet can be glued or simply placed on top of each other. The last option will help you quickly change light bulbs without damaging the lampshade.

Ready-made flashlights

The difficulty here can only arise in the correct folding of the base of the lampshade. As a result, you will get a beautiful and almost authentic Chinese lantern. To give it a more beautiful appearance, you can paint the lampshade by applying Chinese characters or stylized drawings.

Lamp frame

In Japan, paper products are also very popular and widespread. Therefore, you can safely use Japanese motifs when creating a paper lamp. Paper (preferably rice paper) is also here main element. But now it will be supplemented with bamboo sticks. Note! Bamboo grows in Japan, so this element will look great in the overall display of the lamp.
Here you will need the following list of materials for work:

• tracing paper (in the absence of rice sheets);
• ceramic cartridge with a small base;
• thread, preferably thick;
• stain;
• piece of MDF. Can be replaced with plywood;
• wire with switch and plug.

Tools you need to have on hand:

• PVA glue;
• sandpaper;

Finished Japanese paper lamp

• scissors;
• file;
• square;
• brush.

For the base we take plastic corners, bamboo/wooden slats or wire. We assemble the lamp base according to the following scheme:

• we clean the slats sandpaper and cut it to the height we need. This will be the height of the entire lamp;
• We make markings on the slats at the gluing points. They will help to make an even and beautiful frame;
• We coat the joints with glue and assemble the slats into a single structure. For durability corner connections should be knitted with thick thread. This will help strengthen the base and also give it decorative look. The frame itself can be round or square;
• MDF sheet will be used as a cover. We make a hole in the sheet for the cartridge;
• after that everything wooden elements the structures are covered with stain. You can apply varnish on top of it. Such protection will make the tree resistant to negative influence moisture and protect it from wood insects;
• Now all that remains is to attach the paper sheets to the frame. They can be left clean, but it is better to first apply a Japanese pattern or hieroglyph here. We simply glue the sheets to the frame.

This is a slightly more complex version of the lamp in terms of implementation. But it turns out to be more durable and of higher quality, which in a positive way will affect the service life of the lighting fixture.

Glass and paper

The easiest thing to make with your own hands is a glass lamp. This is a portable table lamp that is very quick and easy to make. To make such a lighting device you will need:

• a thin sheet of paper (you can print a specific pattern on it);
• round and tall glasses;
• wire with a thickness of 1-2 mm;
• candles-tablets.

The tools you will need are:

• scissors;
• PVA glue;
• pliers;
• stationery knife;
• scotch.

The algorithm of actions here is as follows:

Bent wire

• bend the wire using pliers so that it takes on the appearance shown in the photo. A candle-tablet will be placed on its lower part. The length of the wire should ultimately be slightly greater than the height of the glass. This will make it much more convenient to remove the candle from the container;

• The glass itself should be decorated with a sheet of paper on which the pattern you like is applied. Carefully glue the sheet to the glass. The top of the container can be decorated using plaster or polymer clay.

Ready glass

As you can see, this requires a minimum of effort and time, and as a result you will get a beautiful lamp, perfect for a romantic dinner or just a quiet, relaxing evening of relaxation.

Paper straws

Probably the most original and unusual lighting device in our “paper” history will be a lamp made from paper tubes. You can decorate any lamp with this lampshade:

• chandelier;
• table lamp;
• floor lamp;
• wall sconce.

Tube lampshade

Such a lampshade will provide a soft and subdued light, which will become a real highlight of any interior, made in any style. Here, as you might guess, the main and only elements of the entire structure will be paper tubes. They can be made from both newspapers and colored paper. The main thing to remember is that the appearance of the lampshade should complement the existing interior in the room.
The number of tubes depends on the size of the lamp on which it will be placed. The “pipe minimum” that should be wound is 100 pieces. The tubes are attached to each other using the same PVA glue, thus forming the required shape:

• round;
• oval;
• square;
• arbitrary.

First, the first row is laid out, and then the entire structure is built on it.

Note! The walls here need to be built in such a way that the lampshade expands towards the center. To do this, the diameter of the mold must be gradually increased, and after the middle - gradually reduced.

If desired, the resulting lampshade, after it has dried, can be painted with spray paint. The result is a solid product without flaws.
This is far from full list possible options making a lamp from paper. But these are the most popular methods that are implemented easily and quickly.

Conclusion

As you can see, making a paper lamp with your own hands is quite simple. There is no need for expensive materials or a lot of time. If you strictly follow the instructions, you will be able to quickly complete the task, and your home will have a new, beautiful and, without unnecessary modesty, original lighting fixture.

When starting to arrange the interior space, it is important to think through every little detail. After all, we all subconsciously strive for comfort and that is the smallest details are able to create a special atmosphere, convey general idea, mood and character of the room. Professional designers claim, and the interiors clearly prove that right choice Chandeliers can not only decorate the interior of a room, but also make life brighter and more fun. Beautiful lampshades for chandeliers with an original design give special grace and luster to the lamps. You can find out how to make them yourself and what materials are best to use for this in this article. Detailed, step-by-step master class, as well as a visual photo, will be an excellent help for you in this exciting process.

Material selection

When making a chandelier, it is difficult to single out one material that would meet all the requirements. Each of them has its own individual characteristics and features. For example, paper, which is the simplest and available material, lends itself well to transformation.

Lamps made from glass shards and strips of metal have a dazzling shine and beautiful appearance. Wood and fabric add warmth and comfort to the interior. Lace lampshades are distinguished by their special beauty, captivating everyone at first sight.

In a word, you can make a chandelier with your own hands from anything, the main thing is to be smart and use your imagination in time.

A chandelier made of paper napkins is a rather bold, but justified experiment.

We will describe in detail how in an ordinary object you can discern its creative potential to create an exclusive decorative element in this article.

Step-by-step instructions, with a description of each step, will help you make from available materials incredibly beautiful and unique lamps that will be an excellent addition to your favorite interior.

What you need to pay attention to before making a chandelier

Many people are interested in how to properly make a chandelier in and other rooms. After all, you want this element of the interior to be not only beautiful, but also functional.

On the one hand, a chandelier is a lighting device that can provide the proper level of lighting in an apartment. After all, a lot depends on the choice of light in the room, including eye safety. On the other hand, I want ceiling structure complemented the interior design, creating a special atmosphere of warmth and comfort.

When making a chandelier, first of all you need to take into account the height of the ceiling. For example, for low people a chandelier with a bar mount is suitable. So, the ceiling will look visually higher. If the ceilings are high - 3 m and above, then it is better to make your choice in favor pendant lamp with hook fastening.

Lamp selection

For any room you need to take an individual approach to the intensity of its lighting.

For a small bathroom you will need 80-100 W.
Kitchens require a lamp power of at least 120-150 W.
The living room and hall cannot do without light bulbs in the range of 150-300 W.

The number and power of lamps is calculated based on established standards - 20 W are required per 1 m². electricity. It is also necessary to take into account the parameters of the room, its dimensions and reflective properties.

Designer Edison lamps - look beautiful and unusual

Design of the lampshade

The appearance, decor and design of the lampshade occupies an important place in the design of a chandelier. It is selected to match the interior of the room, depending on the style. Crystal for classics, metal and glass for, wood will fit perfectly into country or chalet style, fabric and silk are perfect for Provence style.

To illuminate a room on several levels, you can additionally make wall sconces or floor lamps.

Step-by-step master class on making

To make a beautiful ceiling decoration, you don't have to start from scratch. Look around, you probably have something in your house that you haven’t used for a long time. And who knows, maybe it will become the main item in the manufacture of the original lamp. Moreover, there are now more than enough ideas and inspiration for creativity on the Internet.

Important! The best place to start searching for the things you need is in the kitchen or balcony. It is there that we store all sorts of rubbish that we once needed so much and which, as often happens, is so difficult to part with later.

Spectacular chandelier made from mugs

No matter how strange it may sound, it is from dishes and other kitchen utensils that the most unusual and interesting models lamps. For example, tea mugs are an ideal material to make a spectacular lamp.

For work we will need:

• Mugs
• Saucers
• Drill
• Porcelain drill with special hole

We make it quickly and easily

1. In the bottom of the mug, use a drill to make a small hole for the wire, attach the electric cartridge and bring the wire out. It is advisable to seal the hole with a plaster mixture.
2. Next, you need to glue the mug to the saucer, where there should also be a hole, insert a light bulb and hang the newly made lamp in the right place.

As you can see the original and fashion design can be obtained from completely ordinary items.

Mesmerizing yarn chandelier

Since this is quite a simple product, to make it we need a minimum of things, namely:

• Wire with a cross section of 4-5 mm.
• Wire cutters
• Thin thread
• Multi-colored yarn

Manufacturing instructions:

1. A ring is made from wire, the diameter of which will correspond to the future size of our chandelier. To get a perfectly even circle, it can be wound on some object that has a cylindrical shape.
2. We bite off the excess wire with wire cutters, leaving a reserve of 2-3 cm on each side. We tie the ends with a thin thread.
3. All that remains is to decorate our chandelier beautifully and brightly. To do this, we cut the yarn threads so that the length of each segment is twice the height of the lampshade.
4. One by one, we tie the resulting strings onto a knot until we hang them all over the ring. From the same yarn we make a fastening for the hook.

This lampshade can be used both as a chandelier and as a decorative element decorating the interior of the room.

By combining the skills of macrame and papier-mâché you can get a stylish chandelier for the bedroom

Important! To make such a lamp, instead of wool yarn, you can use any other thread. The main thing is that it harmoniously fits into your interior.

Unusual lamp made from a teapot

You will learn how to make a chandelier from an ordinary teapot yourself in this master class. Here's what we need for this handmade masterpiece:

• Kettle
• The wire
• Electrochuck
• Metal chain

Step-by-step manufacturing guide

1. First of all, the lower part of the teapot is cut out. This is done in such a way that the resulting cutting edge is not sharp, otherwise you could get hurt on it.
2. Next, an electric cartridge is fixed to the lid of the kettle, the wire of which is led out through a small hole drilled at the top.
3. A chain is attached to the handle of the kettle, and a wire is threaded through the links. The lamp is ready.

Let's breathe new life into bottles

Glass bottles, especially if they have beautiful shapes, can be used to make a wonderful chandelier. Required material:

• Thin rope
• Flammable liquid (alcohol or gasoline)
• Glass bottles (preferably colored)
• Edison lamps (having a beautiful spiral)
• Wire and electric cartridge

Do it yourself

1. We wrap a rope around the bottom of the bottle, after wetting it in flammable liquid. Then we set it on fire and let it burst, and we begin to slowly rotate the bottle around its axis until the rope burns out completely. After this, we lower the bottle into a container with cold water, wrap it in a towel and, with a little effort, break off the bottom.
2. To cut edge was not sharp, it needs to be polished. To do this, it will be enough to swirl the bottle in sand or fine gravel for a couple of minutes.
3. All that remains is to mount the electric socket correctly, stick the wire through the neck, and screw in the light bulb. From the remaining bottles, the remaining lampshades are made in a similar way.

This chandelier will fit perfectly into any interior, especially if you hang it above the bar counter.

Decor from cans

Lamps made from cans are no less beautiful. They are made in the same way as from bottles. The only difference is that the bottom of the jar does not need to be cut off, since clear glass is usually used for lampshades.

We need:

• Beautiful thick-walled jars (preferably with a relief pattern)
• Hammer and nails
• Wire, electric socket
• Spray paint
• Edison lamp

How to do it right

1. To begin with, using a nail and a hammer, holes are punched in a circle in the lid, after which the inside is carefully squeezed out. The diameter of the circle must correspond to the diameter of the base in the cartridge.
2. We insert the cartridge into the cover and mount the wire.
3. Next, we paint the lid together with the cartridge in the color of our choice. Metallic paint with a golden shimmer will look best.
4. All that remains is to screw in the light bulb, close the lid and install the lamp in its proper place.

We all know what a globe is, but not everyone knows what amazing things can be made from it. For example, a cute lampshade for a chandelier that will fit perfectly into the interior of a children's room.

Here's everything we need:

• globe
• Bulb
• Electric chuck with holding element

Step-by-step master class

1. Usually the design of the globe is not solid, so in order to get the desired element, it is necessary to divide it into equal two parts (hemispheres).
2. Next, at the top point of the hemisphere, you need to make a hole for the cartridge. For this, it is best to use a drill with a crown.
3. The electric cartridge is installed in place and securely fixed by the holding element. Congratulations, your chandelier is ready!

Hanging structure made of horns

Making a unique lighting device from deer antlers is quite simple, the main thing is to have the necessary material on hand.

Such designs are famous for their special sophisticated appearance and are best suited for rooms with high ceilings. Such chandeliers are used in many interiors, but they look especially attractive in country, chalet or rustic style.

As a rule, the shades of such chandeliers have various shapes, and only natural materials are used for their production.

We will need:

• Antler
• Rope
• Copper wire
• Electrical socket and wire
• Bulb

Make a chandelier like this

1. Observing the safety rules, we connect the wire to the electric cartridge according to the diagram.
2. Next, the wire needs to be beautifully wrapped with decorative rope. For better fixation, you can use universal transparent glue.
3. Using copper wire, horns are attached to the lower part of the resulting rope, placing them 2 cm above the cartridge.
4. We repeat a similar procedure with the remaining lampshades, later combining them into a single composition.

Ideas for making beautiful lamps (photo, video)

We hope that useful tips and the photos presented in the article will help you not only make beautiful lampshades for chandeliers with your own hands, but also save your family budget.