Gate: what and how to make it with your own hands, drawings, options, technology. How to make a wooden gate with your own hands. Embed a gate into a stone fence.

Reading time ≈ 3 minutes

After making the decision to fence off the area using a fence made of corrugated sheets, the need arises to install a gate. It can be done without any problems if you follow the instructions suggested in our article.

To make a gate with your own hands, you will need the following tools: a welding machine, an angle grinder with cutting and grinding wheels - a grinder, a drill-driver, a gun for installing rivets, painting brushes, a screwdriver and a level.

Blueprints

Step-by-step instructions for making a gate from corrugated sheets

This instruction presents a method for welding a gate frame directly on the support posts.

1. Initially, you should mark the place for the future gate, leaving an opening of the required width in the fence between two posts, to which you will subsequently need to weld pipes - the basis of the frame of the future gate. Thanks to this scheme, the future gate will fit perfectly in size. In this case, problems that arise when the structure is manufactured elsewhere will be eliminated.

2. The question of how to make a gate is easily resolved. Its frame is made of the same square pipes as the fence frame. To avoid deformation of the gate frame, the pipes are welded to the fence posts.

3. After this, the upper part of the hinges is welded to the vertical post of the gate frame.

To ensure structural rigidity, a cross member from the same square pipe must be welded in the middle of the frame. The horizontality of the crossbar should be checked using a level.

4. At the next stage, the frame of the swing gate made of corrugated sheets should be cut off at the places where the pipes are attached to the posts. It is necessary to cut off all excess pieces of pipes, carefully welding all joints, and clean the welding joints using a grinding wheel.

5. Using a grinder, you need to clean the installation sites of the lower parts of the hinged hinges on the fence posts. First, you should weld the lower part of the upper hinge, after which you can hang the gate frame and weld the lower part of the second hinge in place.

6. Making a gate from a metal profile requires checking that it opens correctly: if everything is done correctly, it opens freely.

7. It is necessary to remove the gate and weld the hinges on the fence posts on all sides, cleaning the weld seams. When welding hinges, it is necessary to protect the corrugated sheets from sparks and scale from the welding arc.

8. Using a grinder, you need to cut out a place for installing a mortise lock, having previously marked all the dimensions on the gate post according to the drawings.

9. The photo shows how, by installing the gate frame on the hinges, you can mark a place for installing the lock strike plate on the fence post. You will need to secure the striker to the fence post using a drill/driver. Next, you should check that the lock is working correctly, after which you can begin painting the entire structure to protect it from rust.

The first impression made on a stranger, and in our case, on a guest, is an important indicator that undoubtedly influences the subsequent attitude of people towards the owner of the house. It is the gate that greets guests at the entrance to the courtyard or garden that is one of the front elements of a private house, as well as a detail that, in addition to its practical function, also plays a decorative, aesthetic role in the design of the house.

Peculiarities

It is unnecessary to talk about the functional significance of the gate without mentioning the importance of the fence itself. After all, it all starts with him. The strength and reliability of the gate and fencing eliminates the possibility of uninvited guests entering the private territory, and also ensures sound sleep for the owners and confidence in the safety of property.

When planning a fence, you need to determine and decide where and how the gate door will be installed. Sometimes homeowners decide to build the fence themselves. In this case, it would be best to do the same with installing a wicket entrance. Some plot areas allow owners to install two gates at once: one for the main entrance, the other for various household needs.

To make the gate, the same material is used that is used to install the entire fence. If this is not the case, it is important to consider the compatibility of these two (or more) materials so that no problems arise during installation.

The standard width of the product is usually at least a meter. This is the optimal size of the opening, which, if necessary, will allow you to bring large items or furniture inside. The height of the wicket product, according to the requirements of SNiP, should not exceed the maximum height of the fence - 2 m 20 cm.

The optimal depth for fence posts is 1 m. It depends on the type of base. Sometimes you can limit yourself to 70 cm. If a heavy soil layer predominates on the site, it is necessary that the pillars be installed below the freezing point.

Sometimes owners have to terracing the dirt strip under the fence in order to even out differences in height between sections, unevenness, and also eliminate gaps that provide a chance for uninvited guests with four paws to get into the yard.

The handle and lock of the gate are usually located at a level of 90 cm from the ground. However, even minor flaws in the placement of these elements will not affect their functional value.

One of the inventions and innovations of our time is the automatic gate.

Opening and closing of the product occurs using automatic means, and also includes a number of advantages:

Remote control. The gate is opened and closed even when the homeowner is at a considerable distance from the entrance.
Increased security. In combination with other elements of the security system (video surveillance cameras, intercom), it makes it possible to find out and establish the identity of the person who comes remotely, as well as decide whether to open the door gate or not, without leaving the house.
Save time. The automatic gate opens by pressing just one button.
Strength of the material. Wickets with an automatic function can be made of high-strength material.

This is just a small list of the advantages of an automatic product from a huge list. However, just like in its functionality, the price of this purchase also differs significantly from simpler and standard options.

In this article we will look at options for decorating a gate yourself and make sure that it is not so difficult, especially since creativity and creativity take place in the process of performing this work.

Materials

As has already become clear, gates differ in the installation method, design, and also in the material used. There are many different options in choosing material. As a rule, it all depends on the amount of money the owner of the house has.

The entrance gate can be made either from a simple picket fence or from expensive cast iron. However, metal and wood still remain traditional materials. For example, a metal gate goes well with a fence made of stone, brick or metal.

The tree is in harmony with the fence made of the same material. It is impossible not to notice that forged products have always been famous for their long service and sophistication. Nowadays, gates made from corrugated sheets or corrugated sheets are especially popular.

Let's look at the main materials and analyze their advantages and disadvantages.

Tree

Wooden gates come in the form of a solid sheet or made of wooden slats. Precious wood species are rarely used for production. As a rule, the work is done from pine or larch logs.

Wood is one of the cheapest bases for a fence. A block, a picket fence, a batten - all these are easily accessible and inexpensive materials. It's very easy to work with them. Restoring a wooden gate should also not be difficult. In case of rotting, the post is dug up, cleaned of dirt and rot and impregnated with a special protective impregnation or antiseptic for wood.

You can install wooden fencing and gates yourself, using a minimum amount of tools. Wooden gate panels have a lot of decoration options.

The main disadvantage of such gates is their fragility. Even with the most careful care, at best, the gate will last no more than 8 years. The presentation of the product does not remain the same due to the material fading in the sun, as well as due to rotting.

Wooden fencing is more suitable for summer cottages than for fencing mansions and cottages, since the mechanical strength of such a gate is not so high. A structure held together with self-tapping screws and nails can be easily damaged. Rather, it serves as a symbolic designation of the boundaries of possessions.

Wood is susceptible to combustion, so this material is especially fire hazardous.

Metal

Often this is either a metal sheet with elements of forged decoration, or a completely forged product.

The material is easy to assemble and install. A huge plus is the high service life of the metal structure. The product is a universal, reliable home protector, and also has a presentable appearance.

But metal is susceptible to corrosion. However, this problem is easily solved by painting with special paint solutions.

Undoubtedly, one of the main advantages of forged fences is their noble appearance. An artistically forged product stands out among the landscape and becomes a kind of “highlight” of the overall picture. Forged gates are very durable and weather resistant. The latest welding technologies are used in the production of a forged product, so it will serve for many years.

But the process of installation and manufacturing is very labor-intensive and requires a lot of effort, time, and sometimes money. Opening and closing such a product can be difficult due to its heavy weight.

Corrugated sheet or corrugated sheet

In fact, these are two names for the same material. Corrugated sheets are metal sheets that are produced by stamping. This is a universal material. Its popularity is explained by its reasonable price and excellent quality. Wickets made from profiled sheets are strong, reliable and durable, and also look very solid.

It is easy to install the gate yourself. Its scheme is very simple, and the process itself does not take much time. The material has soundproofing properties. The color range of the product is very wide. The material is not subject to external influences and fading.

Apart from the possible slight deformation of the gate under strong wind conditions, there are no disadvantages to a product made from corrugated sheeting.

Nowadays, there are many options for fences, gates and gates made from the above materials. These can be fences and gates made of chain-link mesh, different types of European picket fences, gate doors resembling blinds, etc.

Decor

Gates made from absolutely any material can be beautifully decorated. For example, making an openwork, carved wooden gate is not as difficult as it might seem at first glance. Armed with a jigsaw and a wood saw, you can cut out various patterns using ready-made sketches.

Curly carved overlays are another way to decorate a wooden product. Pre-prepared openwork linings are attached to the panel door leaf. The cover itself can be either wooden or metal. Curtains or corners for wickets or gates look especially beautiful. As for gates made of sheet polymers, they can be decorated by combining a plastic sheet with a metal frame.

Making a decorative item from forged metal requires basic skills in working with this material, but it is quite possible to do it yourself.

Forged metal gates or wickets are a metal sheet or iron rods woven together, decorated with various decorative elements. The secret of the elegance of forged gates lies in the correct selection of forged elements and a well-constructed drawing. It is also necessary to weld the elements together with the utmost care.

Forging elements are perfectly combined with corrugated sheets. You can decorate such a canvas by arranging the forged elements according to the drawing, and using welding, secure them to the gate canvas.

photos

A canopy or small roof installed over the gate will protect the owners from bad weather or rain while they are busy looking for the keys.
A lock or latch will ensure strong and reliable locking of the gate.
A lamp or remote spotlight will help illuminate the space at the entrance.
A hanging bell or bell on the gate will help notify homeowners about the arrival of guests.
An intercom and a surveillance camera make it possible to remotely make decisions regarding whether to open the gate door or not.
If the door gate is high, you can make one of its sections in the form of an insert made of transparent polycarbonate, which will make it possible to see those who come without coming close to the gate or gate.

If there is a reliable fence made of metal profiles around the house, then the question of what to make the gate from resolves itself. Installing a gate in the opening of an existing fence is quite simple if you know how to work with a welding machine and other installation tools. It is very important that the gate is light, reliable and resistant to precipitation. And the metal profile fully meets these characteristics.

Metal profiles for fences and gates - pros and cons

Corrugated sheeting is one of the most popular materials for the construction of gates and other enclosing structures.

Main advantages of the material

Resistance to external factors and corrosion. Profile sheets are covered with modern polymer materials that can withstand intense exposure to ultraviolet rays, moisture and temperature changes.
Ease and simplicity of installation. A gate made of metal profiles can be made in one day if you have the skills to work with a welding machine. Its production does not require the creation of complex drawings and diagrams.
Attractive appearance and wide selection of colors. The covering of the gate can be easily matched to the fence, gate or finishing materials of the house.
Long service life. The structure made of corrugated sheets will last more than 50 years.
Affordable price compared to other facing materials.
The possibility of constructing fences of any height, since the maximum length of the profiled sheet is 12 meters.
Excellent performance characteristics. The metal profile does not require painting or repair. You can wash it with plain water from a hose.

Flaws

Low degree of sound insulation.
Small sheet thickness. Corrugated sheeting can be easily cut through with an ax, deformed with a strong blow, and even bent by hand.
Even small scratches lead to the appearance of rust on the surface of the material.

Therefore, when making a choice in favor of corrugated sheeting, it is necessary to take into account all the pros and cons of this material.

Gallery of fences made from corrugated sheets

A fence, gate and gate made of corrugated sheets, made in the same style, create a reliable and beautiful fence A fence installed on a concrete base will last much longer The decorative coating of corrugated sheets is not only monochromatic Corrugated sheeting can be supplemented with decorative elements so that the fence from a distance will resemble a massive concrete fence Fence posts made from corrugated sheets can be made from metal profiles, concrete or brick A gate made of corrugated sheets is often decorated with forged elements With the help of wall corrugated sheeting you can imitate not only brick, but also natural stone

Preparation for the start of work: drawings and dimensions of the frame

The standard width of a swing gate is 1 meter. With such dimensions, it will be possible to easily bring garden, upholstered and cabinet furniture, as well as other large objects onto the site. If the width of the structure is greater, this can lead to rapid wear and tear of the hinges and, as a result, deformation of the gate.

The height of the gate should not be more than 2–2.2 m. If the fence is higher than these parameters, then the low gate will not look entirely aesthetically pleasing. Therefore, in the opening between the posts above the gate structure, you can install metal jumpers with an insert made from a piece of metal profile.

But if people over 2 meters tall live in the house, then you will have to install a higher gate with reinforced hinges, and strengthen the frame with additional transverse metal slats.

The gate can be made without the top crossbar, which will significantly simplify the task and solve the issue with the height of the structure.

A good profiled sheet should not only be galvanized on both sides, but also have polymer protection at least on the front surface. For the construction of the gate, you can choose a material with imitation of stone or brickwork, as well as with a natural wood pattern.

For the installation of a gate, material marked “C” or “NS” is suitable. The numbers after the letter designation indicate the height of the profile wave. For cladding gates, sheets C20 and C21 are recommended.

The metal profile is made from rolled steel, so it can have different lengths. To install the structure, the sheet can be used both in length and width. When purchasing a profile, take into account the thickness of the sheet. It is not worth making a gate from a material that is too heavy, as it will create a large load on the hinges, but something too thin will not work either. A sheet with a thickness of 0.45–0.5 mm will be optimal. The 0.4 mm profile is considered a budget option.

The height of the corrugation is an important indicator of the strength of the material for the construction of gates and other enclosing structures. For cladding the gate, it is recommended to use a profile with a wave pitch of no more than 21 mm.

In the simplest case, sheet marking consists of designating its type, wave height and sheet width

When marking on the sheet, the parameters are indicated in the following sequence:

profile height;
sheet thickness;
sheet width;
profile length.

Corrugated sheeting can be coated with powder paint or polymer. The second method guarantees the durability of the coating and color saturation. The sheet can be coated on only one side or on both sides, which provides a more attractive appearance. Colored polymers come in about 30 different palettes.

Making a gate from corrugated sheets with your own hands

Since we will weld the gate to existing supports, we will not have to concrete the posts, which will greatly facilitate and speed up the work.

List of materials and tools

To install a gate made of corrugated sheets, you will need a minimum of materials and only the most necessary tools:

metal profile - sheet C21–1150 with galvanized or polymer coating - working width 1 meter, length 2 or 2.2 meters;
metal square pipe - section 40x24 mm;
two metal door hinges (can be polymer) – ɸ30 mm;
deadbolt and street mortise lock.
gas or electric welding;
Bulgarian;
cutting and grinding wheel for metal;
screwdriver and powerful drill;
rivet gun;
paint and brushes;
plumb line or building level, 5 meter tape measure;
construction angle;
Screwdriver Set.

Stages of manufacturing a swing gate

We present a method for installing a swing gate made of metal pipes and metal profile cladding directly onto support posts.

First, we mark the place where we will install the gate and make an opening in the fence of a certain width between two metal supports. In the future, we will weld pipes to them, which will form the frame of the gate. By choosing such a scheme, we will initially be sure that the finished gate will exactly suit all parameters. Then the problems that arise when welding the gate in another place will not appear.
We weld the preliminary fence frame in accordance with the measurements taken. The distance between the supports must be more than 1 meter in order to obtain a gate measuring 1x2 meters. To avoid deformation and tilting of the frame, we weld it to the support pillars in several places.
We weld the upper part of the hinges to the vertical post of the frame. This is necessary in order to see at what level they should be.
To strengthen the structure made of pipes, we mount a cross member in the middle from the same square pipe. All angles must be 90°.
We check them using a corner or level.
After we are convinced that the frame is smooth and correct, we cut it off at the welding points and place it on a flat surface.
We cut off all the excess pieces with a grinder and re-weld all the seams again.
Then, using a grinder and a grinding wheel, we clean the joints.
After this, we clean the fastening points by welding the lower elements of the hinges on the supports themselves to remove rust.
We weld the lower element of the upper hinge, then hang the frame and weld the second part of the hinge on top in place. If the frame of the gate is welded correctly, it will open and close freely and easily.
We remove the gate and weld the hinges more carefully, and then clean all the seams. During welding, it is necessary to lay an asbestos sheet or ordinary cardboard so that sparks and scale do not fall on the corrugated fence.
We mark the place for the mortise lock on the frame of the gate according to the drawing and cut it out with a grinder. The lock and handles are installed at a height of 80–90 cm from the ground.
We cut out the holes and screw the lock strike plate using a screwdriver. We check the operation of the lock, the ease of opening and closing the gate. Then we paint the structure with protective anti-corrosion paint.
We take corrugated sheeting, pre-cut to size, and use a drill and a rivet gun to attach it to the gate frame. As an alternative, roofing screws can be used.
If you intend to install a rim lock, which will be located on the inside of the gate frame, we place the mounting holes for it on the crossbar of the frame. We drill holes in the profiled sheet using the “drilling along the contour” method, and then additionally process them with a cutter. To secure the lock in the cross member of the structure and the plate welded to it, using a drill with a drill and a special tap, we make a threaded hole for installing a screw.
We install decorative overlays with handles on the lock.
We make a limiter for the gate. To do this, we install a metal blank inside the opening, which we cut off from the pipe.

You can assemble such a gate with the help of a partner within a few hours.

Video: how to install a metal profile gate with your own hands

Video: how to fit a lock into a gate

Installing a bell on a gate

A call that runs on batteries or rechargeable batteries is the most reliable and convenient to use. Also, such calls can work from a stationary radio receiver. On average, the distance from the gate to the bell is about 130 meters. The main part of the device is installed inside the house on the wall.

The wireless bell consists of two parts, one of which is installed on the gate, and the other in the house

The receiver operates from a 220 V network or on batteries. When choosing a call, you need to take into account such nuances as:

presence of different melodies;
aesthetic appearance;
good lighting;
additional fasteners (not including Velcro);
bell weight (it should be up to 50 g);
compliance with the operating temperature conditions declared by the manufacturer;
protection from UV rays, frost, snow and rain.

Before purchasing, you need to check that the range of the bell corresponds to the distance between the gate and the house. It makes no sense to take a powerful device with a range of 150 meters if the house is 50 meters from the gate, but a weak device with a range of 20 meters will not work in this case either. Wireless calls usually have a mute feature, which will be useful at night. The body of the street bell must be durable, compact and sealed.

Calls that are made to operate in regions with the lowest possible temperatures are equipped with anti-freeze batteries. The best option would be if the outdoor button can operate in the range from -20 to +35 °C, and the receiver itself - from 0 to +35 °C.

Setting up a call

When installing a bell on a gate, keep in mind that the range stated by the manufacturer implies an open area without obstacles. If there are intermediate structures, the reception radius will be significantly reduced. Therefore, it is necessary to choose points between which there are no concrete or metal structures.

The radius of the call is significantly reduced if GSM network equipment is nearby.

In quantitative terms, the reception area is reduced:

by 10–20% for gypsum and wooden structures;
by 25–40% for brick walls;
by 40–85% for reinforced concrete products.

Modern wireless calls are often equipped with additional signal repeaters to increase the operating range.

Installation stages

We choose the optimal place to install the button: under the visor of a support post, on the side of the metal profile frame bar, etc.
If the bell has double-sided tape on the back of the case, you can simply remove the protective film and press the case to the marked installation point. Before this, you need to thoroughly degrease the surface with a special solution.
If you don't trust tape, you can attach the body with self-tapping screws. Usually it has special holes. If they are made in corrugated sheets, then they must be treated with an anti-corrosion compound.
To attach the bell to the metal profile, we use special self-tapping screws of a special shape, made of galvanized steel. After attaching the body, we carefully treat all places with self-tapping screws and cloth with sealant. Since the corrugated sheet is a multi-layer product with protective layers, any “invasion” into them can lead to premature corrosion.
On a rechargeable bell, you will need to change the battery occasionally. To do this, you need to remove the case and replace the power source.
We install the base station inside the house above the front door or in another convenient place. We simply attach the stationary receiver to the wall by hanging it on a nail. Network receivers should be hung near the outlet. The most expensive bell models are equipped with AA or rechargeable batteries with a long service life.

Video: how to protect your wireless call button from vandals

Making a gate from corrugated sheets is quite simple, so you can easily assemble it with your own hands, without the help of craftsmen. Using a minimum of materials and the necessary tools, you can make a wicket for the fence and gate of your home in one day. It will serve you for a long time if it is not subjected to strong mechanical and physical stress. This is especially true for the profile sheet itself, since it is the most vulnerable link of this structure.

Traditionally, metal and wood are used to create gates. It could be slab, or it could be natural bog oak, it could be corrugated board, or it could be cast iron with gilding and hand forging. The price and specific type of material depend solely on the budget and personal wishes.

The manufacturing principle is largely the same.

Here we will tell you how to make a gate with your own hands from the simplest, most accessible and inexpensive materials: corrugated sheets and ordinary boards, and also what types of fence gates there are in general.

Wood or metal: what to choose

Metal

Metal is a universal material, durable and with a long service life. It looks beautiful with both a metal fence and a brick one; with proper skill, it can be “fitted” into an ensemble with a wooden fence.

The iron gate will not allow either strangers or prying eyes into the yard. It is reliable enough to scare away potential robbers, and its appearance can be anything you want, because the metal is inexpensive corrugated sheeting, exclusive forging, and ordinary tin sheets from the nearest construction market. Actually, a few disadvantages will depend on the subtypes of materials:

forging is expensive, the process of its production is labor-intensive: it is beautiful, durable, elite and prestigious, but it is unlikely that you will forge with your own hands if this is not your main activity or favorite hobby;
the cheapest materials are highly susceptible to corrosion; This can be easily handled by treating the metal with anti-corrosion agents, priming and regular painting - during which, by the way, you can change the color at your discretion;
Corrugated sheeting is ideal in terms of price-quality ratio, but some people don’t like its external simplicity, plus - you need to know how to choose it.

Wooden

Sometimes wood is cheaper than metal: for example, when building a gate for a fence with your own hands at the dacha, if you plan to install a temporary solution from slabs and wood waste. Really high-quality beautiful boards are not cheap. They are not easy to find, but high-quality wood will look great.

Advantages - relative ease of construction, appearance. Disadvantages - even the best wood will not last longer than 10 years. It will begin to deteriorate and will have to be repaired, repainted, saved from mold, rot and woodworms.

The service life of metal with proper care is 30 years.

How to make a gate from corrugated sheets

The basis of any gate is a frame. The stronger and more reliable it is, the longer the entire structure will last: this is also true in the case of installing fences with your own hands.

Assemble the right frame - and you can install any material on top of it: corrugated sheets, tin, wooden boards, chain-link mesh or picket fence, cheap or expensive.

Choose a location. It must be clearly known at the stage of fence construction. Having determined the place, close it between two support pillars. You get: fence - post - empty space for the gate - post - fence.
Make a frame. The most convenient and easiest way is to do it right on the fence. In other words, weld the frame directly to the support posts: this way you will definitely not be mistaken with the dimensions. Use the same posts and crossbars that are used to build the fence.
Weld the loops to the workpiece.
In addition to the frame frame, weld the crossbar closer to the top of the structure. It will strengthen the frame. The crossbar needs to be level, so be sure to use a level.
Cut the frame off the fence. Cut off all excess - you should get a completely flat frame without protruding parts. Having placed it on the ground, thoroughly weld all the joints again and sand any sharp chips and nicks.
Weld the top hinge to the support post, hang the gate frame on it, then put a mark on the support where the bottom one should be, remove the frame, weld the bottom one. By the way, this stage is a great opportunity to make sure everything is going right. If the gate clings to something when opening and closing, it means that an error was made somewhere in the installation. Go back a few steps and double check.
Install the lock and handles. There is nothing complicated here: choose a place on the frame, drill holes in the posts using a grinder, and install a counter plate in the fence post. To prevent mistakes, periodically hang your work back on the hinges and check that everything is at the same level.
Put the gate in place, open and close, lock it, unlock it. Everything should run smoothly, quickly and easily.
Treat the frame with anti-corrosion compounds. This is a very important point! Any unfinished metal other than stainless steel is susceptible to corrosion. To prevent it from deteriorating prematurely, all metal parts must be treated with special solutions, preferably several times.
Weld the corrugated sheet the way you like. For example, you can make the cover a continuous sheet, of course, cutting out a place for the handle. Or you can make a designer version: one color on top, another color on the bottom. Here everything depends only on your imagination.

A gate made of corrugated sheets can be installed with your own hands in 10 fairly simple steps, and if you have already built a fence yourself, then there will be no difficulties with it.

Instead of corrugated sheets, you can hang other materials on the frame - the principle remains more or less the same.

How to make a wooden gate for a fence

Now let's talk about how to make a wooden gate with your own hands.

Make a frame. Any gate begins with a frame, to create which you need to take all the measurements. The frame structure itself is assembled from strong beams, which are hung on supports. The more accurately you make your calculations, the less you will have to cut and redo.
The beams for the frame are fastened together using metal corners: ask them at any hardware store. As a result, you should end up with a rectangular frame.
At the same time, prepare the boards that will be attached to the frame frame: usually these are long, processed boards adjacent to each other and located perpendicular to the ground. They should be 10 cm longer than the frame at the top and bottom. This will make the finished product look more beautiful.
Try on the frame. There is no need to attach hinges yet, just place the future gate on the supports: lift it from below with a threshold, hold it in place on the sides with nails. If something doesn't work or doesn't look good, redo it while you still have time. If everything is ok, move on to the next step!
Install the hinges. Fortunately, wood is a malleable and easy-to-handle material, so drilling hinges into boards will be easier than drilling into metal.
Screw the boards to the frame with self-tapping screws. Treat them with compounds against insects and rot, prime them and paint them in any color - or leave the boards in their natural form, this also looks stylish.

As a lock, you can install a latch or a lock, you can also install a standard lock - the installation principle is the same as in the case of a metal gate.

If you are going to install a wooden gate on a brick or stone fence, then you need to attach the wooden sides to the brick pillars with self-tapping screws. Loops will be hung on them, and a lock will be installed in them. The same applies to installing a metal frame, only use iron ones instead of wooden sides.
The simplest and cheapest gate made of chain-link mesh can be installed in just a few hours. Make a frame frame as we explained in the section with corrugated sheeting, then stretch the mesh over it instead of the corrugated sheet. You can stretch the mesh using a metal profile - a crossbar or X sign is made from it from the upper corners to the lower ones.
The principle of working with Euro picket fence is the same as with corrugated sheeting: you make a frame, then attach picket fences to it.

After building a full-fledged fence with your own hands, making a gate is a relatively easy task, but if you want to get rid of unnecessary hassle and entrust the work to the craftsmen, contact us. We manufacture wickets and gates ourselves, taking into account the wishes and suggestions of customers, as well as the features of the fence. The materials we work with are corrugated sheets, European picket fences, and chain-link mesh.

(17 ratings, average: 4,26 out of 5)

A fence with a gate is an essential element of any suburban area. Making a door that is installed in a fence structure is quite simple. A home handyman can easily complete this task. If you have never done this, you can make a simple version, which is a structure made from a frame welded using shaped metal. You can use an angle bar or choose square or rectangular pipes.

Enough to have necessary set of tools, as well as prepare materials in advance. If you have minimal skills in working with metal, after spending a few days, you can create a gate for your fence.

What is corrugated sheeting?

Increasingly, people choose corrugated sheets for their suburban areas for the construction of fencing structures. You can use it to build a gate. The corrugated sheet itself is sheets of metal that are produced by stamping. During the production process it is given a certain profile. The rigidity of the material depends on the wave height of the sheet. In addition, this parameter affects the scope of application of the material. It is worth noting that corrugated sheets S-8, S-10, S-20 used mainly for the manufacture of vertical structures.

The presence of the letter “C” in the marking of this material can be deciphered as “wall”. Based on the numbers that follow this letter, every home craftsman can draw a conclusion about the height of the wave in the sheet. This parameter is indicated in millimeters. Everyone probably understands: the higher the wave height, the stiffer the material is and the higher its strength characteristics.

DIY metal profile gate: diagram

Before you start creating a drawing, you must take into account the following nuances:

The maximum height of a gate made of corrugated sheets, as well as the entire fence on your site should not exceed 220 cm.

How to make a gate with your own hands: tools and materials

To make making a metal gate with your own hands for a fence easy and not cause you any difficulties, and the product to turn out beautiful, you should think about preparing the necessary tools. If you already know how to weld a gate from a profile pipe, you cannot do without this tool. To make a gate from a profile sheet without unnecessary hassle, The following tools will be required:

Necessary materials

For the manufacture of gates from corrugated sheets with a wicket consumables will be required, as well as accessories:

ready-made concrete or cement-sand mixture, which you will have to make yourself;
bitumen mastic;
remnants of roofing felt or high-strength cellophane;
primer for metal with high anti-corrosion properties;
metal paint. To decorate a gate with a wicket, you should choose enamel that can protect metal surfaces from corrosion;
OSB boards. You should choose a material that is at least 1 cm thick. Or, as an alternative, you can purchase a thick sheet of plywood;
door lock, which must be designed for installation of a metal profile. For gates with a wicket, you should choose a mechanism that can be installed on the metal profile of the wicket. It is desirable that it has an insert that is designed to be operated from one side without the use of a key or lever.

Installation of support pillars

It is necessary to cut blanks from the rolled strip according to size, which you have indicated on the drawing.

Having received the workpieces, it is necessary to clean them from rust and scale, and then carry out the manipulation of covering them with a primer composition. When this is done, they must be left until completely dry.

After this, you need to start creating holes in which the pillars will subsequently be installed. It is optimal if their depth is more than a meter. The width should be 30 cm greater than the diameter of the pipes used. When the pits are ready, it is necessary to line their bottom with the remains of roofing material or lay down a plastic film, which is intended for waterproofing. A layer of crushed stone must be poured onto the bottom.

After this it is necessary install support posts. It would be a serious mistake if you simply install a metal profile in a hole. Before doing this, you need to lubricate the end of the pipe that will be in the hole with bitumen mastic, and when the pole is immersed in the hole, you need to level it using a level and plumb line. After this, you can fill the hole with concrete.

After a week has passed after completing this operation, you can begin hanging the wicket. However, first you need to make it.

Preparing poles for hanging

If you already have a fence with gates and installed support posts, they must be prepared for the subsequent hanging of the gate. Work order in this case will be determined by the material from which the pillars are made:

When erecting brick pillars, usually steel plates, which are equipped with pins, are immediately embedded in them. In another way they are called embedded parts. An easier way to install hinges is to weld them to the plates. Sometimes, to increase strength, a section of profile is first welded to the parts, and only then the hinges on which the gate will be attached.

If the pillars are made of concrete, in this case you will have to carry out work on drilling holes. Serrated metal pins will then be driven into them. And after that, go to them a profile section will be welded, which will be used to install a gate made of corrugated sheets with your own hands. You can refuse to carry out impact work using a sledgehammer, but then you will have to use modern anchor bolts.

Frame assembly

To make a gate frame from corrugated sheets, it is necessary to cut blanks from square pipes in accordance with the dimensions indicated in the drawing.

The OSB sheet prepared in advance must be placed on a flat surface. The components of the future gate made of corrugated sheets will be placed on it.

Using clamps, all parts of the future structure should be secured. It is necessary to achieve parallelism, as well as right angles, for which you need to use a square. Clamps must be placed as close as possible to the welding site. In this case, better fixation will be ensured. This simple device will allow you to adjust all the design details.

Then it is necessary to connect all the parts by welding. Next, you need to weld the finished hinges to the frame, and in addition, a plate that will be used to attach the lock, and a handle for opening the gate made of corrugated sheets. It is not recommended to remove the clamps until all the seams have cooled down.

Next, you need to install the parts of the hinges without the pin on the gate. It is advisable to drill holes and then attach the hinges to the profile using self-tapping screws. In this case, you will be provided with convenience when carrying out welding work.

Next, you need to cut a hole in the profile for the lock. Using a grinder, long cuts are made, and to make short cuts, a series of holes are drilled. You also need to cut holes for the handles and key. A drill with a metal burr will help with this. When all the cuts have been made, it is necessary to process them, for which you need to use a file. With its help you easily remove sharp burrs. After this work, it would be useful to weld a regular bolt onto the longitudinal crossbar of the gate. In this case, the reliability of the gate will significantly increase. In addition, you will have the opportunity to close it from the inside.

Installation of hinges, lock sheeting and gates

You should start by inserting the parts with the pins into the hinges, and then attaching them to the support post. The places where the holes will be made must be marked with a pencil. Next, you need to drill holes and then use self-tapping screws to attach the hinges. After this, it is necessary to secure the part to the pole by welding. Next will remain clean the weld area, and then coat it with a primer. You should check how the frame moves on its hinges.

Then we deal with the corrugated sheet, which must be prepared in advance. Holes are drilled in it. First, you should mark the hole in the gate, for which you need to attach the finished part. Next, using colored screws and rubber seals, we attach a sheet of corrugated sheet crosswise to the frame. After this, you need to screw the screws into the remaining holes.

All that remains is to hang the finished gate on the installed door hinges. Then you will need to cut a hole in the corrugated sheet for the door handle. Then the locking mechanism and the gate handle are installed. After this, you should mark a place on the door post for a cutout for the lock. After cutting it out, you need to clean the cut. Remains check the closing and opening of the gate. When this work is completed, it is advisable to paint the structure again with colored enamel. It is necessary to select a paint that matches the corrugated sheet. After completing such work, the gate will serve for a long time, since it will have higher resistance to atmospheric precipitation.

Conclusion

When a person purchases a country plot, the first thing he does is erect a fence to protect against intrusion. For unimpeded access to your own property, a gate with a wicket is required. Many people make fences and gates from corrugated sheets. This material is inexpensive. Pipes are used as the base of this structure square or rectangular. This design is quite reliable.

The use of stiffening ribs in its composition ensures the strength of the gate and prevents unauthorized persons from entering the territory of the land plot. The technology for manufacturing gates with a wicket for a fence is quite simple. By following the recommendations contained in the instructions, you can easily make it yourself, while saving your money. If you know how to make a wicket and use high-quality material, you can get a reliable wicket that will serve for a long time, pleased with the proper work. And in the future you will no longer have the question of how to make a gate from corrugated sheets with your own hands.

Fence gate