Country swing made of logs. We swing children on a swing made by ourselves. Wooden beam option

Children can play for hours on the outdoor swings. The child is attracted by the feeling of flying. IN apartment buildings swings are installed on children's playgrounds, and caring parents install them in private areas.

The simple design makes it possible to make a hanging swing with your own hands. Moreover, children can be involved in the design, construction or decorating process.

Outdoor wooden swing - children's joy in flight

Making swings from wood is the most common practice. This is not surprising, because they have the following advantages:

environmental friendliness;
availability of lumber;
relatively low cost;
ease of working with wood;
safety. Wood is a soft material, which reduces the risk of serious injury from a fall.

Thanks to the properties of wood, children's wooden swings can be found in almost any private yard or country house. In terms of mobility, they are divided into stationary and portable. Swings made of wood, unlike metal ones, are often made stationary, because the tree does not have sufficient weight for stable standing (the frame of a wooden swing requires reliable fastening).

Based on this feature, it is necessary to consider the installation location of the swing.

Where to put the swing?

When choosing a place you need to consider:

viewability. The child should be visible whenever possible;

remoteness. The economic zone and the nearby pond are not a place for games. If there are no other options for installation, you need to fence off the areas. Also make sure that the swing is placed at a safe distance from fences, walls with windows, trees, etc. flight obstacles. It is also not worth installing a swing near communications;

illumination and shading. The installation location should be light, but create a shadow, especially in the summer at midday;

humidity. Outdoor swings made of wood will become unusable from excessive moisture, not to mention its harm to the child;

absence of drafts;

absence poisonous plants, allergens, honey plants, thorny bushes;

surface topography at the installation site. The installation location of the swing needs to be leveled. Then you won't have to change the length support pillars, and nothing will interfere with the child’s enjoyment of his favorite pastime;

quality of fastening of each swing unit.

How to make a wooden swing with your own hands - step-by-step instruction

To be sure of reliability, you need to build the swing yourself. Step by step guide for beginners it will allow you to indicate the right direction and construction plan.

Stage 1 - choosing the design of a children's swing made of wood

Children's wooden swings must be safe - this is an axiom! In many ways, their ability to stand stably is determined by the configuration of the support (frame). Before you start work, you need to decide which wooden swing frame will be optimal for installation. After all, its shape affects the safety of the structure and determines the place and method of its installation.

Types and types of frames for swings

U-shaped frame

It is considered the most economical model. Less lumber is used to make it. In addition, the supports do not interfere with the child’s movement and cannot cause injury due to negligence. However, for stability, the structure requires concreting of the supports, therefore it is stationary. The frame is ideal for installation on soft soil and making hanging sectional swings.

L-shaped frame

It is sometimes called an inverted "V" support. More stable compared to the previous version. This option allows you not only to hang a swing, but also to create a children's corner.

X-frame

It is a type of L-shaped, only the support beams are fastened not at their junction, but slightly lower, at a distance of 150-200 mm. At the intersection vertical bars the jumper is laid. This is a simpler way to make a support. It should be noted that such a frame requires additional reinforcement in the form of a side support.

A-frame

The most reliable of all structures, due to the jumper that strengthens it. It is this frame that should be preferred if you plan to expand the swing by arranging stairs, installing a climbing rope and other elements of the playground.

Stage 2 – drawing of a wooden swing for children

Having a drawing or sketch of a swing helps determine the optimal dimensions of the structure, calculate the load, choose the right section of wood for manufacturing, determine the amount of material and parameters of the workpieces.

Drawings of a wooden swing must contain:

frame configuration (shape);

dimensions of a wooden swing. It should be noted that the dimensions of the swing are the height, as well as the perimeter of the base;

presence and installation location of additional reinforcing elements (kerchiefs, spacers);

number and type of seat (taking into account the age of the child);

type and length of suspension (ropes, chains, cables, etc.);

You can make an additional drawing with a detailed breakdown and dimensions of the workpieces.

The dimensions of a wooden swing are determined based on:

the age of the child - the length of the suspension, the size and configuration of the seat depend on it;

height - determines the length of the suspension.

You can make a swing “for growth”, then:

The optimal seat width is 600 mm.

seat height above the ground – 500 – 550 mm. On the one hand, this will allow you to swing and stop the swing on your own, and on the other hand, it will not interfere with skating;

height from seat to crossbar – 1,600 mm. To make it comfortable for the child to swing while standing;

the total height of the swing from the ground to the crossbar is determined taking into account the thickness of the seat.

Advice. The seat and suspension must support the weight of the child. For reasons of practicality, it is better to make a safety margin of up to 100-120 kg (several children or a child and an adult).

Stage 3 – material for wooden swings

To make a wooden swing with your own hands, you need to choose the right wood. It is better to give preference to durable types of wood - oak, larch, or cheaper ones from spruce, pine, birch. The main thing is that the lumber is dry, good quality, without falling knots, holes and other defects.

Depending on the type of frame you need to prepare:

for a U-shaped frame - timber 80x80 or 100x50 - 2 pcs. For all other types of frame – 4 pcs.;

for the crossbar - timber (log) of the same cross-section - 1 pc.;

for sitting - boards 600x300x25 - 1 pc. To make seats for children under 2 years of age, we consider additional elements– back, handles, fences;

for suspension - a welded chain with an anti-corrosion coating or a strong rope (the one used by climbers is suitable). The length of the suspension is equal to two heights of the swing. On average – 4,500 mm – 1 piece;

for fastening the frame - wood screws 80x4.5 - 40-50 pcs., as well as self-tapping screws 50x3.5 - 250 pcs.

for attaching the suspension - carbine, hanging hooks, steel corners. Quantity - depending on the method of fastening;

for wood processing (protection) – primer;

for decoration - paint or wood varnish.

for concreting racks - cement, gravel and sand (for installation of a U-shaped frame).

Tools you will need: screwdriver, saw, plane, sander, level, drill, plumb line.

Stage 4 – making a homemade wooden swing for the dacha

We move from theory to the practical implementation of the project. Let's look at how to make a wooden hanging swing with your own hands.

Preparing a site for installing a swing

After choosing a location, you need to remove any remaining construction debris, remove thorny bushes and level the site.

Note. Some users advise concreting the area for the swing, citing the fact that in the place where children push off from the ground, a hole appears in which water accumulates. Others believe that this is the least of the troubles. After all, the fall concrete base this is a serious risk.

Preparation of lumber

Outdoor hanging swings made of wood should be safe for children. Therefore, you need to sand each workpiece to prevent the appearance of splinters. And also cover everything wooden elements primer. You can prime a ready-made swing, but then there is a risk of destruction of the wood at the joints.

Installing a frame for a children's swing made of wood

As discussed above, there are several ways to construct a frame. Therefore, let’s look at the main nuances of installing each of them:

U-shaped frame. The arrangement begins with fastening the vertical posts and the upper lintel. Then you need to dig two recesses (the depth is 1/3 of the height of the support). Pour a crushed stone-sand cushion onto the bottom, install a stand, pour concrete, wait until the concrete hardens, and install a suspension with a seat.

Note. The lower part of the supports must be treated with any means that will prevent rotting of the wood. The most budget-friendly and reliable option would be to use used engine oil.

L and A-shaped swing frames are usually also assembled on the ground. Procedure: saw four supports at an angle for a more reliable connection. Then attach the top crossbar to the knot. In the case of an A-frame, a crossbar is added, which makes the structure more stable. Then the assembled frame is installed in the prepared place. For reliability, you can dig it into the soil (pre-treated with an anti-rotting primer) or secure the lower part of the supports to the ground using a long rod and bracket.

X-shaped frame for swings. This is done similarly to the previous one. Only the ends of the supports are not sawed off, but are fixed to each other. A jumper is placed in the formed upper corners.

Note. To installed frames The X, L and A-shapes did not sink into the soil; users recommend concreted areas under the base. This eliminates the possibility of the structure being distorted and maintains its mobility.

The weak point of the X, L and A-shaped frames is at the junction of the vertical supports and the lintel. To make this unit, long self-tapping screws are used, but, as the craftsmen note, it is advisable to use a nozzle pipe of suitable sizes. The photo shows this element and its installation location.

Advice. When making a frame, you need to fasten the screws in this way: first drill a hole with a diameter slightly smaller than the diameter of the screw, and then assemble the blanks onto the screw. Some craftsmen recommend gluing the joints of the workpieces for reliability, while others recommend strengthening the knot by using metal plates or wooden spacers.

Swing seat arrangement

The manufacturing method and material of the swing seat are determined by the age of the child. Children are not picky about design; they will be quite happy with a seat made of a tire or a simple board. At the same time, you can count a dozen ways to make it.

Attaching the swing to the crossbar

A suspension (cable, rope or chain) is attached to the crossbar. A hanger is a swing unit for attaching a swing to a crossbar. The suspension bears the maximum load, which means they extend to it special requirements on safety.

Note. The seat is installed only on chains or cables, and not on wooden or metal hangers. Garden swings are designed for adults and do not need adjustment, while country swings made of wood for children need to be adjusted as the child grows.

Attaching the swing suspension and seat can be done in several ways using different fasteners:

throw the rope over the crossbar and tie or fasten it with a staple;

using metal plates that are attached to the crossbar at the top;

using a carabiner.

Material prepared for the website www.site

By screwing an anchor into the crossbar and attaching the suspension to it.

By enveloping the timber.

Stage 5 – decorative design of the swing

Decorating a wooden swing has a dual function. On the one hand, it protects wood from external factors. On the other hand, the original design of the swing forms a beautiful and bright element of the playground. The main rule is that paints and primers must be of high quality and safe, so as not to harm the child’s health.

As an additional decoration, you can install additional jumpers on the frame, which will strengthen it, and the children will have a staircase that will be of interest to those who are waiting in line to ride.

Caring for a wooden swing

Care consists of checking:

attachment points;
suspension;
seats;
quality of paintwork.

give the swing a load greater than that for which it is designed;

avoid shock loads (sudden sitting on a seat);

try to distribute the weight along the plane of the seat (do not tilt);

roll perpendicular to the support. Hanging swings are designed for rolling along supports;

adhere to a moderate swing amplitude to avoid tipping over an unsecured swing.

Conclusion

We test the reliability of the installation of the suspension and seat, and at the same time the strength of the entire structure. If nothing was deformed under the weight of an adult, then it will support a child. However, wooden swings for a summer house require periodic inspection of the main components and attachment points.

It is difficult to imagine a person who did not ride on a swing at least once as a child. Even as adults, many still love to relax and swing in the garden at the dacha, not to mention children. Many install structures bought in a store on their site, and some create country masterpieces on their own. The editors of the site bring to your attention a review from which you will learn how to create a fairly popular attraction - Garden swing do it yourself: photos and drawings will be a good help with this.

Read in the article

Types of garden swings with photographs of models

Swings are divided by material of manufacture, type of construction and purpose. For example, there are designs for adults, children and the whole family. Let's consider some features of various designs depending on their purpose.

Swings for adults

Swings for adults are distinguished by their simplicity and increased structural strength. They can be stationary or portable. Swings for a summer house are made from a variety of materials and must withstand a load of more than 120 kg. Designs can have a variety of shapes.

Garden swing

Attraction for children

children's swing for outdoor garden

Designs for the whole family

Attractions designed for the whole family are large, stable structures with a wide surface that can accommodate several adults at the same time. For greater comfort, the swing is equipped with a wide awning that will protect from the scorching sun and rain. The designs have the most various sizes, are made of different materials and can be either stationary or mobile.

Design of a garden swing and materials used

Swings can have A-, P- and L-shaped support structures. They can also be suspended on chains, cables and balance beams, familiar to everyone from childhood. Depending on the type of swing, when making an attraction for adults and children, corners, logs, plastic and scrap materials are used.

Comfortable swing seat

A regular (the simplest option), an old one, can be used as a seat for a swing. car tire, or a bench with a back, sofas. Structures intended for children must be equipped with special seat belts.

Hanging chairs

Attaching the suspension to the supporting structure

The attachment of the seat to the support can be rigid or flexible. The first option uses a wooden beam, a metal corner or a pipe. Cables, chains and ropes are used for flexible suspension.

Swing seat with chains and ropes

The flexible suspension allows you to build a swing from scrap materials and install it very quickly. The simplest option is a board and two pieces of rope, which are attached to a thick tree branch on the site or veranda. Using chains, ropes and cables, you can attach the seat to both stationary and mobile support structures. It is not recommended to use flexible harnesses for riding small children, since such structures are not stable and unsafe twisting of cables, chains or ropes is possible. To set up a swing, it is better to use chains or metal cables, since hemp ropes can stretch and sag, which will affect the reliability of the structure.

Wooden swing with soft sofa and an awning

Rigid suspensions made of metal and wood

Use for hanging seats from supporting structure wooden beams, metal corners or pipes have their advantages. This option is more reliable and allows you to withstand more weight. A rigid suspension is best suited for children's swings.

How to make a swing “nest” with your own hands

The “nest” is a suspended structure with a round wicker seat. This swing model is also called a “basket” or “spider web”. The nest swing can accommodate 2-3 children or one adult. However, strong ropes must be used to suspend this attraction.

To create such an attraction you will need following materials:

climbing safety rope, hemp or synthetic cord with Ø 5-6 mm for seat arrangement;
durable fabric and felt for exterior finishing seats;
steel water pipe for the installation of a supporting structure;
gymnastic hoop Ø 900 mm for making a seat frame.

Playgarden Hanging swing “Nest”

Scheme and step-by-step instructions for creating a do-it-yourself outdoor swing for your dacha

The creation of a “nest” type swing begins with the manufacture of a wicker or textile seat. If the attraction is intended only for children, then gymnastic hoops will be needed. The structure, designed for adults, is made of a steel pipe with a diameter of 16 mm and a length of 1,500 mm, which is formed into a circle on a pipe bending device. The joint is welded. Cables are attached to the frame, and the hoop is braided using the dream catcher or macrame technique. The seat cords are pulled tight to prevent sagging. The hoop is finished with foam rubber and textiles or tarpaulin.

When the seat is ready, you can begin to create the support structure. To do this, you can use a profile pipe or a thick wooden beam. The support for hanging the seat is made as follows.

We assemble two side A-shaped structures.
If the swing is stationary, then the sides are dug into the ground. The distance between the supports must be equal to the height of the structure.
The sides are connected at the top steel pipe, to which the seat will be attached.
Cables, ropes or suspension chains are attached to the crossbar. To prevent abrasion of the cables from contact with the pipe, a polyester gasket is placed under them.
The seat is attached to cables, ropes or chains using four carabiners.

After the structure is ready, it needs to be tested for strength. To do this, it is necessary to place a load with a total weight of about 120-150 kg on the seat. This will allow you to check the tension of the cables, the braid of the hoop, and also adjust optimal distance between the seat and the ground.

How to make a metal swing with your own hands at the dacha

Metal swings for dachas can be stationary, with a rigid structure, or collapsible. The first option is preferable because it provides greater stability, safety and reliability. However, in this case, welding skills are required. Collapsible design less reliable, since loosening of the joints may occur during operation.

Drawings of a DIY metal garden swing

We present one of the solutions for constructing a garden swing.

We invite you to watch a video on how to make a metal swing with your own hands.

How to make a swing from a profile pipe with your own hands

Profile pipe – best option for the manufacture of metal swings, especially collapsible portable structures. This is due to the fact that in this case you can do without welded joints. The swing can be easily assembled using nuts. As we already said, bolted connection less reliable than welded due to loosening during operation, but this problem can be solved by regularly checking the fastening points and, if necessary, eliminating the resulting play.

Let's consider the option of creating a metal swing for a summer house from profile pipe using welding.

Drawings for making a country swing with your own hands

Detailed manufacturing instructions

To make a metal swing from a profile pipe, you will need the following materials and tools:

electric drill;
square and tape measure;
"Bulgarian";
metal brush;
paint brush or roller;
40 × 40 × 2,000 mm – 5 pcs.;
pipe 20 × 20 × 1000 mm – 2 pcs.;
profile 20 × 40 × 1,000 mm – 3 pcs.;
board 20 × 90 × 1,500 mm – 7 pcs.

Illustration	Description of action
	To begin with, take two pipes and at an angle of 45°. We check the angles: internal - 45°, and external turn - 90°
	We take a piece of pipe for the cross member, measure 700 mm from the bottom edge and mark the corners. We cut off the excess with a grinder and a cutting wheel. Using welding, we connect together all the parts of the A-shaped sidewall. The distance between the lower ends of the side pillar should be approximately 1,600 mm
	We make the second side of the swing in the same way.
	We install the sidewalls, and on them we place the upper crossbar, on which the swing seat will be attached. We check the angles between the vertical posts and the crossbar: they should be exactly 90°
	Additionally, we strengthen the structure with two sections of profile pipe, which we use to connect the sidewalls. It is necessary to weld two “ears” to the upper cross member for attaching the seat hangers
	Now let's start making the swing seat itself. To do this, you need to take three sections of profile pipe with a cross-section of 20 × 40 mm and attach them together by welding. Step back 100 mm from the edge and place the first mark. Next, apply marks at a distance of about 120 mm from each other
	Using a grinder, make V-shaped cuts at the marks. The most extreme cuts should be made with reverse side. After all the pipes have been cut, you need to bend the structure to the desired shape
	All joints in each pipe must be boiled, and the excess must be cut off
	Separate the pipes, weld and clean all the seams using a grinder and paint
	We attach the pipes to the cut boards. To do this, drill holes Ø 4 mm in them. We fix the boards using self-tapping screws
	It turns out this is the seat

(18 ratings, average: 4,00 out of 5)

Kindergarten swing in the country is a casual game, great leisure time and fun. There is always a lot of children's laughter and joy around them. By installing them in your summer cottage, you can get another place to spend time pleasantly. Observing simple rules creating a design and safety, you can make a children's swing for your dacha with your own hands.

In order to do it right calculate capabilities and strengths, you must first determine the preferences of family members and get acquainted with manufacturing options (photos and drawings of swings for the garden can help with this). Some people prefer to lie languidly with a book or tablet, while others need to rock with their ears whistling.

Types of homemade swings

Wooden garden swing are divided into several main groups:

balancing or sofa swing for the cottage. This type of swing is for two;
hanging swings on chains, cables or ropes, like a bungee;
swing made of logs, which are on stationary supports (classic look).

Each model can beat this way that the household will choose it as their favorite corner of the garden or dacha, and all the neighbors will begin to envy.

Where to install?

When to choose made in favor of bungee, then the answer to the question is obvious - we install it on the nearest tree, which in terms of strength inspires confidence. And when choosing a place for other types of swings for a summer residence, it is necessary to take into account the following factors:

illumination The best thing, to Sun rays got to the site until evening. Thus, a garden swing made of wood will be protected from dampness;
sufficient distance from fences, walls, wires, trees, sharp-pointed objects and thorny bushes;
the site should not " blown by all the winds" Constant drafts are fraught with colds;
It is advisable to immediately select a smooth surface topography so that there is no need to perform additional work.

It’s great when it’s under the structure soft grass or sand. This will make it possible to avoid injury from reinforcement or stone during a fall.

Gallery: DIY garden swing (25 photos)

Drawings of a swing for a summer house

You can do without them. However, when a serious project is meant with a claim to long-term operation, then, for reasons of saving building materials, it is advisable to prepare a drawing of a swing . Design a wooden swing It won’t be difficult to do it yourself if you have at least a little experience in such work.

General provisions that reflect the drawings of kindergarten wooden swings:

sizes. That is, the base area and height;
frame structure;
type of suspensions and their length;
number and type of seats;
It is necessary to mark the locations of reinforcing elements and fastenings.

Material for production

Whatever type of swing is chosen, it is necessary focus a lot of attention on the quality of the material (directly on the wood) from which the structure will be constructed. Quality wood not only can ensure the durability of the structure, but also, most importantly, guarantees safe operation.

The following species performed well: larch, oak and cedar. Also, wooden swings are often made from birch, pine and spruce.

Wood you need to buy dry, without areas of rot or traces of mold. There should be no holes made by pests, crevices, or falling knots. Constructing a wooden swing with your own hands does not require a large volume, so you can check every beam and board.

Tools

Before you make a swing at your dacha with your own hands, you need to make sure you have all the tools required for this.

You will need:

This basic tools. When everything is prepared (project, drawings and materials), we begin to build a garden swing in the country with our own hands.

In this case, the main difficulty is what to hang it on. When you have a suitable tree growing, it is advisable to make the crossbar from a log (about 25 cm in diameter and 3 meters long), secured with ropes. A strong branch at the required height will eliminate need for this design. When not at the dacha a suitable tree is found, then, in addition to load-bearing beam, you will still need two logs (30-40 mm in diameter) to assemble the U-shaped frame.

Pre-logs are needed treat with antiseptic and polish, then they are placed in prepared holes (50 cm) with crushed stone at the bottom and filled with cement mortar. When pouring cement is not planned, the logs will need to be dug to a depth of at least a meter.

When installing the frame, the most important thing is to prevent distortion. Exists interesting option adjust the level correctly: Egyptian plumb line. D This system is quite is simple: the top weight is a nut or any curved piece of iron, and the bottom weight is a small container with sand.

As for sitting, there are many variations to suit every budget and taste:

from a board (with or without a backrest, on two hangers or on one central one);
from a log (one thick diameter or 2-3 thin ones, which are connected to each other with fastenings or rope);
from a tire (solid or cut, horizontal or vertical arrangement).

To the choice of material for suspension, with which we will hang a bungee for fastening, it is necessary to treat it responsibly. Cables, ropes or ropes must be reliable, preferably new, and not rotten from attic supplies. Not recommended in in this case Use chains, as a child can easily get their fingers pinched in them.

Hangers during fastening on the supporting beam must be no closer than 1.5 m from each other. They can be secured using leather-wrapped loops or hooks. You can also use special steel fasteners - thimbles. The most durable fastener is a carabiner with a clamp. However, the carabiner must have safety teeth, otherwise it may move during strong swinging.

Usually , frame swing for a summer residence they have a fixed, solid base, for example, a sofa or bench. This is a more permanent structure, unlike rope structures. Most often, this structure is installed not only for children, but is also perfect for relaxing with the whole family. Construction options will depend from the selected material.

Log swing

Today, swings made from logs are quite relevant. Though they look bulky, but reliable and original. The seat can be hung on L-shaped, U-shaped and X- or A-shaped frames.

At the same time, X-shaped frames are the easiest to make: a load-bearing beam is placed on top of logs fixed in a “cross” (about 12-15 cm in diameter and 2.5-2.8 m long). The cross begins approximately 45-60 cm from the ends of the logs. For fixing, threaded spokes (15 mm) are best suited, which are secured with nuts on both sides after installation.

The lower ends of the supports are cut inward at an angle of 45 degrees. Afterwards, it is necessary to attach ties to each cross in the form of small thickness bars measuring 2-2.5 m at a level of 35-50 cm from the lower ends.

We install both crosspieces and fasten a third tension log between them at the same height as the first two, and also fasten a load-bearing beam in the upper grooves. The frame of the swing is made of logs. Now you just need to hang a sofa or put together a bench. The simplest seat can be easily built on a frame made of 6x8 cm timber, which is then covered with a 4 cm thick board. The parameters of the bench-sofa are as follows:

back height 70 cm;
bench depth 60 cm;
length 180 cm.

Strong ropes, ropes, ropes, and chains can be used as suspensions. They are secured to the bench with carabiners or knots. But for fastening to the cross beam, two eye nuts and two large bolts will be needed.

Stages of installation of hangers:

In the places where the hangers are fastened, two holes are made through from top to bottom in the supporting beam.
The bolts are inserted here, and the eye nuts are screwed in at the bottom.
Carabiners or ropes are inserted into the rings of the eye nuts.

Near a large bench, as a combined option, you can attach a single bungee for children to a long supporting beam.

This is a fairly convenient material for assembly, so building a wooden swing from timber in the garden with your own hands is not very difficult, however, skill will not hurt.

To assemble a swing from timber with your own hands, you will need the following material:

for tightening the crosspieces one edged board 4x12x70 cm;
for the crossbar one block 10x10 cm long 2.7 m;
for side supports, four 12x12 cm bars, 3.2 m long;
for bench: approximately 15 linear meters a bar measuring 4.6x5.5 cm, for covering 20 linear meters of boards 2.5x4.5 cm, as well as fastenings and hangers.

First of all, we assemble the crosspieces. This is done in the same order as the principle for a wooden garden swing made of logs: mark, cut, connect, hang a chair or bench.

On a swing made of timber, the sheathing of the crosses of their thin slats looks great, where you can attach flowerpots with flowers. A lightweight roof would also be quite appropriate. A very interesting option is when the roof is made into a “house”, like over wells in the village. If you use as much imagination as possible, this “haven” in the garden will become a favorite place for family recreation. Especially with soft cushions on the bench.

Wooden pallet

Probably many could see the lattice wooden coasters for various goods in warehouses and stores. Often, after the goods have been delivered, they remain on dacha areas. However, the idea of building a garden swing from it with your own hands can only come to a person with a remarkable imagination. The most important thing is that the pallet is not rotten and strong. It must immediately be treated with water-repellent and antimicrobial compounds, painted and dried.

So, here’s another idea on how to make a garden swing for your dacha with your own hands, and very quickly. A cable, rope, rope or chain is secured on 4 sides of the pallet and suspended on any frame or support. Thus, you can make a luxurious seat on which two children can comfortably sit and rock together on both sides. Or, by placing a pillow and mattress on it, we get practically a cradle.

When the farm has two pallets, then by securing them with corners, you can build a bench that will look great on any frame base.

Balancer or swing scale

Once upon a time, such entertainment for two was a mandatory attribute on children's playgrounds. Not only children, but also romantic older people willingly rode them. On garden plot This swing will definitely come in handy.

When with suspended structures everything is relatively clear, how to make a wooden balancing swing for your dacha with your own hands? This swing can be made from boards, bars and logs.

For the simplest classic version you will need:

metal or wooden pin;
a piece of thick saw cut or log;
two handles;
two beams measuring 30x30 cm;
a board at least 4 cm thick and about 2.5 m long.

So, the construction process is quite simple:

We lay the log on its side.
We secure it on the sides with bars so that it doesn’t roll on the ground.
Having found the center, screw the pin.
We put a board with attached handles on the pin.

And now another garden wooden swing is ready.

How to care for a wooden swing?

From the end to the beginning of the new season, you need to cover the structures with waterproof material.
Annual painting or treatment special compounds will save the swing from pests and rotting.
Do not create disproportionate loads.
Not allowed on metal parts manifestations of rust.

A garden wooden swing is a great way to relax in the country. It’s even more pleasant if they are made with your own hands. Their construction does not take a lot of time, but you can enjoy the result literally every day!

How can you diversify your holiday at the dacha, make it easy, fun and enjoyable? There are many ways, and one of them is installing a swing in the garden or on a specially designed playground. Whether it is a separate structure or a device in a play complex makes no difference, the main thing is that it brings a lot of joy and positivity. To save money and at the same time please your loved ones, you can build a garden swing with your own hands: they will compare favorably with purchased models due to the originality of the idea and exclusive finish.

Before you start creating a sketch, you need to answer two questions: where will the structure be installed and who is it intended for? Depending on the answers, they make an estimate, prepare a drawing of a garden swing, and select tools and materials.

Swings located outdoors are often equipped with a canopy, which serves as protection from the sun (rain) and at the same time is an interesting decor.

One of the simplest structures is a swing on A-shaped supports with a seat-bar

There are a lot of solutions, so for convenience, all products can be divided into three categories:

For the whole family. This is a large structure, often in the form of a bench with a high back, which can accommodate several people. The product is suspended from a durable U-shaped frame using chains. A small canopy on the cross beam allows you to use the swing in almost any weather.
Children's. Quite a diverse group: here are frameless products consisting only of a suspension and a seat, and strong structures with a seat in the form of an armchair, and large structures boat type. Frame models are safer. Any type of swing for the youngest children should be equipped with safety belts.
Portable. Mobile swings of this type are usually hung indoors: in the house, on the veranda, in the gazebo. They can be removed at any moment and installed in another place.

Each of the listed types has its own advantages and can be used in the country for relaxation and entertainment.

Bench swing: step-by-step instructions

Swinging alone is certainly boring, so we present an option for fun company– a swing in the form of a wide bench that can accommodate several people.

The proposed parameters can be changed - for example, making the seat wider or narrower, the height of the backrest a little more or less. The main thing is to be able to sit comfortably and relax. This swing is designed for a garden or recreation area; both children and adults can use it.

Taking the bench seat as a basis, you can invent various design options for the swing as a whole.

The sofa swing is suitable both for relaxing with a book and for a cheerful conversation with friends

A country swing can be hung from a large horizontal branch, but it is better to install two posts with a cross beam specifically for them.

Preparation of materials and tools

If construction has recently been carried out at the dacha, there will be no questions in finding materials - after all, everything you need is already at hand. Wood is best suited for manufacturing - a soft and malleable material, but strong enough to support the weight of several people. Birch, spruce or pine are perfect both in terms of characteristics and cost.

Boards – suitable and inexpensive material for building a swing

So, the list of materials:

pine boards (100 mm x 25 mm) 2500 mm long – 15 pieces;
board (150 mm x 50 mm) 2500 mm – 1 piece;
self-tapping screws (80 x 4.5) – 30-40 pieces;
self-tapping screws (51x3.5) – 180-200 pieces;
carbines – 6 pieces;
welded chain (5 mm) – along the height of the swing;
galvanized screws with rings – 4 pieces (pair 12x100 and pair 12x80).

Metal parts and screws can match the color of wood or, conversely, be contrasting (for example, black).

To build a garden swing made of wood, traditional tools for processing this material are suitable: a drill with various drill bits, a circular saw, hammer, jigsaw or hacksaw, plane. A square, tape measure and pencil are useful for measuring workpieces.

Procedure

Pieces of one and a half meters long should be sawn off from the boards. The corners of the workpieces must be straight.

Thanks to precise markings, the swing will be smooth and beautiful

The thickness of the finished planks should not be less than 20 mm. The load on the back will be much less, so a thickness of 12-13 mm is sufficient. The approximate number of slats for the seat (500 mm) is 17 pieces, for the back (450 mm) - 15 pieces.

To protect the wood from cracking, holes for self-tapping screws are drilled with a drill, selecting thin drill. The depth of the hole for the self-tapping screw is 2-2.5 mm.

Holes for self-tapping screws will help save wood

To make the seat and back comfortable, it is better to make the parts of the base on which the slats are attached not straight, but shaped. To make them, you will need the thickest board (150 mm x 50 mm). Thus, you will get six shaped parts for the frame.

The contours of the future part, applied to the workpiece with a pencil or marker, will help to cut it out accurately

Having chosen the required angle of connection between the back and seat, you should combine the parts into the frame and fix the slats one by one, making equal intervals between them. First, the ends of the parts are attached, then the middle.

By nailing the central strip first, it is easier to align the remaining elements

The armrests are made from two bars of arbitrary width, then fixed with one end on the seat, and the other on the back frame.

The finished swing must be coated with varnish or paint.

The best place to attach the ring screw is at the bottom of the armrest pillar.

To prevent the nuts from going completely into the wood, washers must be used. Similar rings are screwed to the top beam on which the swing will hang. The chain is attached to the rings using carabiners - the place for relaxation and entertainment is ready!

Simple swing with different seating options

A simple and versatile option - side stands for swings on which you can hang different kinds seats. Let us dwell in more detail on the installation of the supporting structure.

Part of the chain can be replaced wooden blocks cylindrical

The material and tools for construction are the same as in the previous description.

One of the seat options is a sofa designed for 2-3 people

Externally, the design looks like this: two posts in the shape of the letter “A”, connected by an upper crossbar. To begin with, it is important to calculate the angle of connection of vertically standing parts. The wider the intended seat, the wider the racks should be spaced. The beams (or pillars) are fastened at the top with bolts for reliability.

Support structure posts

To vertical elements do not diverge, they are fixed with crossbars at a height of 1/3 from the ground. When installed, the crossbars will be parallel to each other. Best mounts for them - corners mounted on self-tapping screws.

Fixing the load-bearing beam using additional elements

Usually one pair of crossbars is enough for the screed, but sometimes a second one is made - in the upper part of the structure. Together with them, they strengthen the place where the upper crossbar is attached - with inside install metal or wooden overlays in the form of a trapezoid.

Cross bars increase the stability of the supporting structure

A supporting transverse beam is attached to the finished side posts, and then the structure is installed in the ground. To do this, dig two pairs of holes (at least 70-80 cm deep - for greater stability), at the bottom of which cushions of crushed stone (20 cm) are placed, posts are inserted and filled with concrete. To check the even horizontal position of the top beam, use a building level.

For the smallest summer residents, a chair with insurance is suitable

The upper crossbar can be equipped with fastenings installed at different widths, resulting in a structure on which you can hang various swings - from simple rope swings to a family sofa.

Material on how to do this may also be useful hanging chair with your own hands:

When installing a children's swing, you should remember that safety comes first, so all parts should be thoroughly sanded with sandpaper. For the same reason, wooden elements must be “without a knot, without a hitch” - defective wood is not suitable for load-bearing structures. Sharp corners must be smoothed with a file.

Use a sander to quickly process wood.

It is also worth taking care of the swing itself. Treatment with impregnation, finishing with paint or varnish will prolong the life of the structure, and galvanized fasteners will avoid destruction of the wood from the inside.

Photo gallery of original ideas

Since you will be making the swing yourself, you can get creative and give it some originality. Of course, decorating a product is a purely individual decision, but some ideas can be borrowed from ready-made designs.

When spring comes, the golden season begins country life. Gardeners are drawn to garden beds, and craftsmen are drawn to arranging their plots. Creating a comfortable, beautiful space is as necessary as cultivating a vegetable garden. I would like to provide each family member with something to do to their liking. Children also need to be offered an interesting, exciting pastime. If you create for this the necessary conditions, rest on fresh air It will be a great success. For example, make a children's swing for your dacha with your own hands, similar to the samples shown in the photo.

Children's swing made of iron

Purchasing a ready-made swing design will undoubtedly save time, but will not allow you to show your personal imagination and dexterity. The industrial version is beautiful, convenient, and not cheap. These are often bulky models that require a lot of space.

Small children's swing with awning

For your dacha with your own hands you can create various designs swing. The work is not difficult, but it will bring great pleasure. It's nice to watch how a child enjoys new fun. Pride in making a swing with your own hands will give you high spirits, and playing with your child will bring a lot of happy moments.

You can easily create a swing with your own hands from any available materials; you don’t even have to spend money on purchasing structural elements.

Swing for children

To make a baby swing, you can use:

tree;
metal;
plastic;
old tires;
furniture parts;
durable fabrics, ropes.

Large wide wooden swing

Large swing with awning, trampoline and basketball hoop

Any remnants of materials left over from various repair work will be used to make a swing. It will be possible to “attach” various good pieces that would be a pity to throw away. Even shabby furniture will be useful in making a swing. If you show imagination and creativity, you will get a masterpiece from available materials. Anything that should have gone to landfill can get another life.

Small children's swing

When choosing which children's swing to make for your dacha with your own hands, you should think about who will use it and how. It is necessary to ensure the design is comfortable and safe. We must not forget about the characteristics of the age category. Some designs are universal, while others are suitable exclusively for kids.

Swing with wall

1. Swing for the little ones.

For kids, you can offer a rocking chair or a balance beam. These options are suitable for a child from 1 year old. They are the most acceptable in terms of security. Due to the fact that the swing stroke is small, even if the baby falls, he will not be harmed. If you make seats on the swing with sides in the shape of a chair, you will be able to additionally secure the child.

Swing for two

2. Rocking chair.

The easiest way to make a rocking chair is to cut it out of a piece of thick plywood or chipboard (parts old furniture). To do this, you need to draw the outlines of the future swing on the material. This is usually a horse, but you can try any other swing shape.

Children's swing

Using a jigsaw, cut out the intended figure strictly along the contours. In this matter, extreme care is required. Depends on the accuracy of the work appearance future product. Young children are very critical of new things. If your child doesn't like the swing, he may refuse to use it.
The next stage is a thorough cleaning of the edges of the swing. To do this, use a file, sandpaper. This requires a serious approach. Careful processing is the key to the safety of the finished swing.
The swing seat is attached from above between the runners using metal corners. At a convenient distance (depending on the baby’s size), hand holders are installed.
Finally, you can decorate the finished children's swing - paint it bright color, make patterns, carvings. It is advisable to varnish the finished product. Such swings are used on outdoors or directly in the house. The mobility of the option is one of the main advantages of this design.

Children's swing in the yard

3. Balancing swing

A balance swing is a popular option for little ones. The model is a crossbar with seats mounted on a support. The simplest version of the swing is performed as follows.

4. Swings for older children

Wooden children's swing for home

For those who have grown up, standard models can already be offered. Such designs are easy to make. For this you will need:

seat plank (board, plywood, base of an old chair, etc.);
strong ropes, chains;
reliable supports.

Simple things make comfortable, fun fun. If the design is done well, then not only children, but also their parents will be able to ride.

Children's swing in the yard with sun protection

Swings for children

Seat

This element can be made from various available materials. Any piece of material suitable for this purpose can be adapted. If it is a board, it must be processed and sanded. Great option for the swing seat - the base of a used chair.

Children's swing made of wood

Tires are also used (both whole and cut into pieces). The one-piece version is good for its simplicity - tie a rope and you can ride. From the point of view of aesthetics and convenience, a prefabricated model - cut into pieces - is suitable various forms connected with rivets.

A good seat for a swing can be made from a hoop covered with mesh. Required reliable material, knots are made using sea or macrame techniques. You can also stretch a tarpaulin or durable fabric. The metal base is covered with foam rubber, textiles or any suitable material.

Children's swing with slide

A good swing base can be made from wooden warehouse pallets. They are wide and durable. If you put 2 pieces together, it will come out beautiful. hanging bed. This structure is secured at all corners of the product with a chain or rope.

If the swing is intended for a baby, then in addition to the seat it is worth installing a backrest, armrests, and a limiter. For this purpose, treated bars are used, into which ropes are threaded.

Children's swing made of wood with a ladder

Fastening, support

The seat is attached to strong ropes. To do this, holes are made in the base, and the ropes are secured with sea knots. You can simply make grooves and stretch ropes, but then the base will be less stable. Chains are often used instead of ropes. For greater strength, they should be secured with nuts. Chains are not very pleasant to feel; over time they begin to rust and creak. Rope cables also have a disadvantage - they will soon (especially with active use) begin to fray. Rings are used to extend the life of the rope.

Iron swing for children

A strong tree can serve as a support for the swing. In this case, you will not have to install additional design. A good rope is thrown over a thick branch, which holds the seat. This option is still very mobile - we didn’t like it in this place - we are looking for another, more suitable one.

Large swing for children

If good wood not on the site, you will have to install supports. The easiest way is to dig in 2 pillars, which are connected by a crossbar. For structural strength, it is made of metal. Ropes or chains are attached to the beam using a flip method or carabiners. It is permissible to use less strong beams, but then the support is made in the form of racks.

Steam swing for children

To securely fix the supporting elements, the lower base is treated with bitumen and placed in a hole approximately 1 m deep, filled 1/3 with sand and crushed stone. The remaining void is filled with concrete. This way the supports will stay firmly in the ground. Stability is additionally provided by supports. Concrete pillars can be used as support. Then the support will last as long as possible and will not collapse several years later. The wooden crossbar is attached to such pillars with anchor bolts, and a moisture-proofing gasket is used at the joints of different materials.

Children's iron swing

Metal swing

Similar children's swings can be made entirely of metal. To do this, you will need pipes or similar suitable parts with a non-hazardous surface. The design can be done as follows.

Green iron swing for children

First, they create swing blanks - support posts 2 m each, a slightly smaller crossbar (1.5–2 m), 4 sections for attaching bases.
Sand the surface using metal sandpaper and a file.
The base blanks are welded, the racks and crossbar are attached.
They dig 4 holes about 1 m deep.
Place the beams in the holes, fill them with concrete, and leave them to harden (at least 1 week for the solution to set well).
Weld the anchor hooks to the crossbar and the base of the swing to the beams.
Secure the seat.
The finished swing can be painted - this will help extend its service life, protect it from corrosion, and make the structure attractive.

Seat swing

A cheerful swing at a summer cottage will become a favorite pastime for the little naughty boy. Outdoor fun is just what a child needs.

If there are extra metal pipes You can use them to make a frame for stretching an awning. It will help protect the structure from rain.

Functional swing for children

Swing bed for children

Making a swing for your dacha with your own hands is not that difficult task. A little skill, diligence, as well as available means - and fun for a child of any age is ready. Life at the dacha that is boring for a child will turn into unforgettable emotions and happy laughter.