At the dacha there are round windows in the attic. How to deal with condensation that forms. Assembling thermal insulation and installing a roof window frame

Availability of living space mansard roof not only allows you to functionally use the area, but also gives the whole house a special charm.

Play a significant role in this window units, embedded in the slope - dormer windows. With their help extra space transforms, fills with light and air.

Lighting is required for bedrooms and children's rooms located under the roof, kitchens and wardrobes, and for each room you can choose a suitable option.

Dormer windows vary in size, materials, design, and opening methods.

There are two main types:

• inclined. In a room with such a window, there is a large heat loss during the cold season - due to natural air convection. And on a clear sunny day in a hot summer, the room will become very hot. The degree of heating depends on the angle of inclination and location of the window - which side of the world it faces. At the same time, this design perfectly transmits and scatters light and does not require organization extra space for installation;
• vertical. Their main disadvantage is their low light transmittance. Compared to inclined ones, vertical ones provide almost half as much illumination. And accordingly, electricity consumption increases.

Location and parameters of the window opening

Installation of glazed openings is recommended on roofs with a slope angle of more than 25 degrees.

Every residential attic space must have at least one window.

The higher the opening is, the more light there will be in the room. In the same time, high location makes it difficult to see.

When choosing the size, you need to remember that the lower border should be at a height of at least 80 cm from the floor.

Another nuance: when purchasing, you need to pay attention to the location of the handle. This part should be conveniently placed for use in a specific room: the handle located at the bottom can be easily opened by children, but the top handle can be difficult for adults to reach.

The width of the opening depends on the pitch. If you have to trim, you need to accurately calculate the load and strengthen the structure with a horizontal beam.

In order for the aesthetics of the roof to be at the proper level, when installing an attic, it is necessary not to forget about the external appearance of the house, including observing the proportions of the windows.

Glazing is carried out based on the calculation: 1 sq. m of glass per 10 sq. m of premises.

• square and rectangular. The most common types are;
• balcony The design consists of two parts - a vertical window and an inclined one above it, and both parts open;
• extensions. Semicircular or triangular architectural detail installed above the main window;
• cornice They are placed above the main ones; this design is designed to improve visibility;
• lower elements. Placed in the same plane with the main window - under it, if there is not enough space for two vertical windows;
• light tunnels. Indispensable for natural light rooms small area in the center of the attic. They are made in the form of a pipe, one end of which looks like a lamp - to diffuse the light, the other ends on the roof slope.

Device Features

Modern windows are made from various materials.

• frame;
• sash with double glazing;
• salary;
• various accessories.

The frame must be durable and not deform under the influence of sunlight and moisture.

It is made from:

• tree. High quality wood is impregnated protective compounds, applied on top protective covering. Laminated timber frames are suitable if attic floor a bedroom or children's room is equipped - a room with normal humidity;
• plastic. Excellent for installation in rooms with excess humidity, withstands temperature changes, and is easy to clean;
• aluminum The material is corrosion resistant, environmentally friendly, durable and attractive. appearance.

To ensure ventilation at any time of the year, most modifications are equipped with a special valve.

Double-glazed window

Heavy-duty glass that can withstand severe wind and snow loads is used: tempered or triplex.

In fact, the double-glazed window experiences the same atmospheric influences as the roofing and must have a sufficient degree of reliability. Thermal insulation is improved by the inert gas in the glass unit.

The final stages of installation before installing the sash are to attach an insulating flashing around the attic window.

The choice of salary is influenced by the type, and first of all, by the height of the relief. All parts are joined and attached to frame structure, lathing and roofing material.

Slopes are made inside the room: the lower one is installed vertically, the upper one – horizontally, so that the glass does not fog up. In some cases, slopes may be missing.
Rubber seals and linings ensure tightness; it is also important to install them above the window structure to prevent leaks.

Windows also differ in the way they open. A little over a decade ago, the vast majority of attics were equipped with fixed windows. Now on the building materials market there are a lot of modifications with rotary sashes.

The sash rotation axis can be:

• central. The window on such an axis can be scrolled – rotated;
• elevated. The axis around which the window rotates is set closer to the top line of the window;
• side. It opens like a traditional window, usually equipped with a shock absorber to prevent it from slamming shut. This device is also called an attic hatch and is often used to access the roof;
• bottom. Balcony windows with such a sash they open forward;
• combined. The design allows you to rotate the sash 180 degrees, as well as open it by tilting it.

Automatic systems

If the window opening is located high, this may lead to certain difficulties when opening. Such structures can be equipped with a special electric drive, which allows you to close and open the window using a remote control.

Manufacturers also offer all kinds of sensors that respond to moisture, temperature environment, wind, or programmable - with their help you can set a schedule. Such devices give a signal at a certain time - and automatic system closes the window.

Roller shutters, blinds, and blinds are used for shading, as well as for decorating the interior of interior rooms.

Don’t forget about such a practical addition as a mosquito net.
Modern manufacturers skylights We took care of all the little details for ease of use.

An indispensable condition for the durability of the structure is proper installation, while it is necessary to take into account the specific features of a particular case and follow all the manufacturer’s recommendations.

In this case, the owner will receive cozy room, flooded sunlight, And stylish design houses outside.

The installation of roof windows should be carried out according to the instructions and the quality and performance should be constantly checked necessary steps installations. Otherwise, your roof will be of poor quality and leak at the slightest natural damage.

Dormer windows in the roof and three vertical windows - lucarnes in the attic roof

It is important to remember the main stages of installing dormer windows in the roof and their types in order to equip your home as efficiently and efficiently as possible and make the most of the opportunities in the modern construction market.

The first rule that is worth remembering when installing a roof window is that it must be attached not to the window frame, but to truss structure(wooden or metal-plastic window frame).

In order for your structure to be lighter and the window to be installed faster and more firmly, you should install a horizontal beam at the bottom of the window and attach it to the rafter system.

During the installation of the attic structure, it is worth leveling the lower half of the window and screwing all the corners with self-tapping screws, which are necessarily included with the purchased structure.

Next, you need to align the length of the window parallel to the rafters and screw the screws into the oblong holes at the mounting corners. You should not screw them in completely, since after installation you can carefully check everything and, if necessary, adjust the parameters and position of your window system.

A roof window can support itself if its position is correctly and accurately aligned so that there are approximately equal distances between the frame and the rafters.

After a final inspection of the structure and checking all distances and positions, the screws can be screwed into the structure to the base.

It is important to note the fact that attic structures must also have high-quality waterproofing installation from durable material that will maximally protect your room from moisture and atmospheric influences.

Styling insulating materials should be done from the bottom up to fit it as closely as possible to the frame and avoid overlaps and excess material residues. Ultimately, all places where the insulation is connected are screwed and fixed with self-tapping screws.

When installing roof windows for a profile roof, it is worth using a special rail on which a corrugated addition is attached, which can be smoothly attached to the profile. This rail should be 10 cm from the bottom of the frame and extend out to the sides by 30 cm.

After the installation of the attic structure is completed, a special sash or double-glazed window is attached to it.

Insulating operations with a window are carried out from the inside, by laying insulation over the entire area of ​​the frame and closing it from moisture thermal insulation material foil type. Special fasteners can be placed on the insulating structure, which are made by using self-tapping screws or sealants.

If you are the owner of a cottage or private house and want to install attic structure– you should study in detail all types of these structures and make sure of the reliability and strength of your structure.

With the help of an attic you can create an additional room, a bedroom, as well as a kitchen and even bathrooms. Lighting through the windows will allow you to create maximum comfort and decorate your attic room in such a way that it becomes the favorite place of all household residents.

Dormer windows are very popular and in demand at this stage of development construction technologies, since they allow you to save on lighting, create certain style and charm to your home.

It is very important to decide in which part of the house you need to install an attic structure and what number of windows will be most the best option so that the shapes and dimensions of your attic match the parameters of the house and achieve a unique and effective design effect.

Installing an attic window is a very important and responsible matter, the correct decision of which will determine external design your home and aesthetics.

Lukarna - window in the roof of the attic floor

Lucarna(French lucarne, from Latin lux “light”) - a window opening in a roof slope, usually an attic, or a dome, with a vertical frame closed on the sides and top.

Lucarna, for example, is a well-known dormer window on attic roof Houses.

The presence of a hatch allows in attic rooms get more usable space With high ceiling. Through the skylight window you can see not only the sky, but also explore the surrounding area.

The lucarne on the roof significantly affects the appearance of the house. To maintain harmony in the appearance of the house, the number, shape and location of the lucarens must be determined taking into account the type of facade, type and steepness of the roof.

The dimensions, location and shape of the hatch determine the interior of the room in which it is located.

There are several types and shapes of windows - lucarnes.

Lucarna lean-to

Lucarno with flat roof can be made wide enough, even the entire length of the room. Then the attic room with a wide hatch will not have sloping sections of the ceiling.

In the room near the window, furniture for relaxation is usually placed or a table for work is installed.

Lucarne with gable roof

Lucarne with gable roof look good on the roofs of houses with slopes of more than 30 degrees.

The width of a hatch with a gable roof is usually included in 1 - 2 pitches of rafters. Wider skylights often spoil the appearance of the house.

Indoors, the ceiling of the lucarne is made flat.

Lucarne with gable roof

A lucarne with a gable roof looks good on slopes of any steepness and shape. From the outside, the roof of the lucarne is not noticeable from the ground. It is easier to harmoniously place such a hatch on the roof of a house.

A hatch with a gable roof can be made wider - by 2-3 rafter steps (up to 2 - 2.5 m)

The ceiling of the lucarne in the room can be flat, or it can follow the shape of the roof of the lucarne (in the picture).

Lucarne with low side walls

The vertical side walls of the hatch can end at a height of less than 2 m from the attic floor. In this option, the lucarne roof is made gable and the window is pentagonal.

Inside, the ceiling of the lucarne niche follows the shape of the roof.

The low walls of the hatch limit the possibility of using the space near the window to place tall furniture.

Lucarne with semicircular window

From the outside, the roof covering smoothly flows around the hatch from above and from the sides. It is better to use bitumen, metal or ceramic tiles as roofing here.

Inside, the ceiling in the niche of the lucarne is made in the form of a cylindrical or conical arch.

"Bull's eye" with a wide oval window

A bull's-eye window with a wide semi-oval window is usually placed on a large roof slope on the side of the main facade. The soft and smooth line of the roof above the sunroof looks impressive from the outside. The bull's eye lucarna serves as the main decoration of the house.

It is better if inside the attic the window is located entirely in one room. A room with such a window turns out to be very bright and attractive.

Triangular hatch

A small triangular lucarne is most often made to illuminate a staircase, dressing room or bathroom.

A triangular lucarne can also be used to illuminate larger rooms. But such a hatch adds very little space to the attic with a high ceiling.

Inside the room, the ceiling of the lucarne niche follows the shape of the window.

Size of lucarne window in attic roof

The dimensions of the hatch in the attic roof are determined from the following considerations.

To ensure the lighting and insolation required by sanitary rules, the glazing area window openings the room must have at least 1/8 of the floor area.

For a person 176 cm tall, the line of vision passes at a height of 165 cm if he is standing, and 121 cm if he is sitting. To view the surroundings from the attic window, the bottom of the glazing should be at a height of no more than 120 cm from the floor of the room, and it is recommended to place the top of the window above 165 cm.

If the hatch window opens, then in order not to fall out of the window, the bottom of the opening frame must be located at a height of at least 85 cm from the floor. The window may be lower than this height, but in this case everything lower is protected with a metal fence.

Hide

Windows on the attic floor can be very diverse. If earlier the attic was perceived as some kind of addition to the general space, and if there were windows on it, they were not the most complex ones, currently the status of the attic floor has changed significantly. Housing with such a floor has come to be considered elite, and the windows offered for it are quite complex, functional and beautiful.

What is an attic floor?

The attic, in fact, is not a full floor: it is an attic space that is used as a residential or technical space. Thus, from empty space we can get usable area, if you improve it, properly insulate it and...

Most often, such floors are used as bedrooms, recreation rooms, and guest rooms. Less often they are adapted for workshops and storerooms. The attic floor can have the shape of an ordinary room, and several walls can also be at an angle. stand in full height on such a floor it is possible, however, not in all parts of the room. From the attic floor you can make one large or several small rooms suitable for habitation. The disadvantages of such a structure include the lack of natural light. Most often, windows are not planned in such structures, so you have to look for a solution after the construction of the house is completed.

Installing a window into a hole cut in the roof

Why are windows in the attic needed?

Without natural light, the attic cannot be considered an attic floor. To use a room as a living space, you need windows in the attic, the options for which can be quite varied, ranging from inclined structures that are installed directly into the roofing material, and ending with display windows that occupy spaces from the ceiling to the floor. The main task window designs is:

• Creating the necessary lighting in the room.
• Blocking warm air inside and insulation of cold from the outside.
• Giving the desired appearance to the room, because the design is significantly influenced by the appearance of the window.

Where is it better to install a window, and which one?

The design of rooms with can be very diverse, from a simple room, upholstered with clapboard, to complex design, striking in its comfort and splendor. Much depends on what type of windows will be chosen: they should not only insulate heat and create the necessary lighting, but also fit into the interior in the same style.

It must correspond to the dimensions of the room; the dimensions are calculated taking into account the illumination that the structure will provide. If windows are installed between the rafters, their size is usually standard, but if the attic space is large, several structures are selected so that the lighting is uniform. The windows must be of a width that allows them to be placed between the rafters, otherwise you will have to redo the roof, which is expensive and unjustified.

Vertical windows in the attic

In addition, you will need to take into account the slope and height of the roof slopes: if you plan to equip a recreation room, study or children's room, it is better to give preference to large windows. The bedroom requires less illumination, so the window dimensions may be smaller. There are three standard sizes:

• 78x140;
• 78x118;
• 78x160.

If larger windows are required, it is also possible to order standard designs 94x140, 114x118 or 114x140 cm. Less often you come across very small windows, the size of which is 55 or 66 cm; pay attention to what to buy standard window much more profitable, since it will cost several times less than one made to your size.

Helpful diagram for selecting windows from the roof slope

Which windows should you prefer?

Choosing the attic floor , It is important to take into account not only their appearance, shape and size, but also pay attention to the following factors:

• Protection from moisture and precipitation.
• What are the frames made of?
• How the window opens.
• What type of glass unit was used?

Windows can differ significantly in design; the most important role is played by the double-glazed window: the thicker it is, the heavier the window will be, which is not very good for the attic floor, which is why they are often used, equipped with a heat-saving system and filled with argon. This allows you to reduce weight to a minimum, reducing the load on the structure and fittings, while reliably protecting the room from freezing.

It would not be amiss to use triplex technology: thanks to the glass with which the glass is glued, if such a window is broken, there will be no fragments in the room, and replacing the double-glazed window is quite easy. In addition, you need to pay attention to where the window handle will be located. If it is too high and it is inconvenient to reach it, you can equip the window with a variety of drives that will help you either lower the handle lower or control the structure using a remote control.

Remote window control

What other types of windows are there?

There are not only inclined structures that need to be mounted directly into the roof. Some projects have a completely suitable design for building on the attic floor. Most often, such a solution is laid down during the construction of the house, otherwise the entire floor will have to be remodeled later. Such windows are an excellent design solution; they provide a lot of light, and if the house opens good view, you can admire it while relaxing or before going to bed. It is worth noting that such windows have a number of features:

• The complexity of the design and its big sizes, therefore the price for such a solution will be significantly higher than for windows mounted in the roof.
• Heating appliances cannot be placed on the wall directly below the window. You will have to remove them to another wall or install them in front of the window, using special fasteners that are screwed to the floor.
• The use of curtains also causes difficulties; a special frame attached to the ceiling is required.
• Such windows have large area, therefore it is quite difficult to keep the heat in the room.
• A warm structure will have more mass.
• It is necessary to expect that such windows will exist when planning a house. It is usually impossible to install them after construction is completed, or the entire floor has to be dismantled.
• Lighting with the help of such windows will be the most correct and natural, but they provide a lot of light, so if you want to arrange a bedroom on the attic floor, it is better to think in advance that the windows do not face east. If the structure faces south, be prepared for the room to be quite hot in the summer, although the problem can be solved with the help of a tinting film.
• You cannot use more than one. In addition, the wall in which there will be a floor-to-ceiling window should not be load-bearing.
• The structure should not be pressed by the heavy weight of beams and partitions.
• Cleaning such a window is quite problematic.

Is it possible to install it yourself?

Most often, when buying a skylight, the owner wonders how to spend less funds. You should not skimp on quality, purchase cheap fittings or low-quality double-glazed windows. Such savings will ultimately cost you more than the original purchase. good window. The easiest way to save money is to install the structure yourself.

To do this you need to clearly know. In fact, it is not difficult, you just need to strictly follow the instructions; It is recommended to get an assistant, since any installation is much more convenient to carry out together. The easiest way to use a Euro window: it is inexpensive, relatively easy to install, and meets all the requirements for lighting, safety and convenience. Such a window can be installed at any stage of home completion; it is not necessary to lay out their layout right away.

Sequence of installation of an attic window

If it is planned that it will be protruding on the roof, then it must be laid during installation of the roof, since a special box for it is required. This usually requires a flat gable roof: it is easiest to do the necessary preparatory work. To do this, install the side walls, nail boards to them, and cover the structure with roofing material. This protrusion is sometimes called a cuckoo.

When using standard internal window it is installed between the roof beams. They are fixed by a rafter system, a support board is installed for the window, which is attached between the rafters, after which the window frame is attached to it. To prevent the frame from falling out, a fixing bar is placed in its upper part. The sides of the window and the drain must be insulated with roofing material, similar to roof covering.

The sequence of actions during the work should be as follows:

• An opening for a window corresponding in size is cut out in the roof. Rafter system should not be affected.
• For the window frame, a frame is mounted and special support logs are installed.
• Waterproofing and insulation are installed.
• Cover the sides with roofing material.
• A window is inserted.

Before starting work, it is necessary to strengthen the roof structure well, mount a reliable frame into which the roof will be inserted. window frame, the structure can be strengthened using adjacent rafters. Jumpers are attached to them, to which beams are attached to secure the window. The block is installed without glass; it is inserted later. The frame must be higher than the roof level, otherwise water will not drain from it.

Choosing and installing a window is not the most difficult thing; there are a large number design solutions, which can be brought to life by developing a house plan. If it has already been built, you can use convenient standard solutions.

If at the beginning of the last century the attic was positioned as nothing more than housing for the poor, today it is a sign of wealth and good taste of the owner of the house. Windows in the attic - practical and modern solution which many owners want to bring to life country houses and cottages.

There is nothing surprising in the desire to use all possible usable space in your home. For this purpose they arrange in basement a billiard room or, if conditions allow, a garage, workshop, etc. For example, when “developing” an attic, you can equip one or more living rooms. The big drawback of such premises is the lack of access to sunlight, making them more like a punishment cell than a room. But, if you try, you can find a solution to this problem.

As you can already understand, an attic is a habitable attic space, which must have windows to complete the picture. Dormer windows are not a tribute to fashion, but a necessity, and give the roof an interesting appearance. They not only provide the proper level of insolation ( in simple words– sufficient illumination in daytime), but also allow you to admire the night sky at night.

Before we tell you about how to make a window in the attic, we will outline the main stages of turning the attic into a useful living space. If you think that the attic is a dusty under-roof space, you are mistaken. Because a dusty attic can turn into one or even several rooms that can be used for living in the warm season. And if you properly insulate it and install front windows in the attic and install heating, then you can arrange a cozy bedroom here.

From words to deeds. The first step is to choose a place in the attic, assemble and install a frame for the walls of yours. To ensure structural strength, it is better to use 150 mm timber. After installing the frame, consisting of vertical posts and horizontal rafters, cover it with any sheet material for walls. It could be drywall OSB board or fiberboard. mineral wool(you can use insulation in rolls or mats). Don't forget about waterproofing and vapor barrier film. Secure the internal Wall panels. The floor and ceiling are finished in the same way as in a regular room.

Structurally, attic windows are practically no different from ordinary façade windows, the same frame, the same double-glazed window. The only, but by no means unimportant, difference still exists - a special opening system. Normal façade window Not suitable for roof installation. Imagine the picture: you open the sash of a window installed at an angle, which with its entire mass falls on you - at least, a bruise is guaranteed. What if a child suddenly does this?

Therefore, it is best to order windows that have been designed for installation in the roof - they fit perfectly in functionality, design and color of the trim. Roof windows can be made in traditional rectangular shape, but you can choose round, diamond-shaped or triangular windows for your attic: The more unusual the shape of the frames, the more attractive the roof looks.

Advantages of attic windows:

1. special design and suitable characteristics;
2. additional thermal insulation, providing heat savings of up to forty percent;
3. good waterproofing, which is indispensable on the roof;
4. sophisticated opening and closing system;
5. frame and trim to match the color of the roofing.

Be prepared for the fact that it will be necessary to dismantle the roof where the window or windows are installed. This is enough difficult process. Not only do you need to “cut out” part of the roof for a window, while maintaining hydro- and vapor barrier, you also need to correctly install the window or windows, ensure tightness and set up the opening system.

Before you get down to work, don’t cut seven times, but think about whether you can implement your project yourself.

And if even one “no” is found, it’s not worth the risk, because correcting errors can hit your budget hard. Therefore, most the right option will take advantage of the help of roofing specialists. Even if you decide to do everything yourself, you are unlikely to be able to complete all installation steps alone. Enlist the help of at least one other person to be your assistant or partner.

• Decide on the location of the window openings. Make markings taking into account the comfort of use of the future installed window, so that it is convenient to open and close it. Regardless of whether the window is fixed or openable, choose a location that ensures good access to sunlight.
• Disassemble the sheathing. It is more convenient to carry out all work from the inside, sequentially cutting according to the markings layer by layer roofing pie. Try to do this carefully, using the appropriate tools.
• Cut off the vapor barrier film, then the insulation and the waterproofing layer - sharp construction knife to help you. Secure the cut edges of the hydro- and vapor barrier films with a stapler or wide-headed nails.
• Remove the roof covering at the installation site. Carefully remove shingles flexible tiles. Corrugated sheeting or metal tiles can be cut with a grinder, not forgetting to carry out anti-corrosion treatment on the ends afterwards.
• Check whether the dimensions of the resulting opening correspond to the dimensions of the window frame. Install the window frame in accordance with the slope of the roof (the installation angle of the window frame should be exactly the same as the angle of the roof slope). As a result, the window should fit perfectly into the roof design.
• Secure the window frame in the opening using screws or self-tapping screws (as a rule, fasteners are supplied complete with mounting strips). Please use the standard installation kit. If you think that additional reinforcement of the structure is needed, purchase mounting strips, although usually those included in the kit are sufficient.
• Insert the glass unit and secure it with special glazing beads. If the window is delivered disassembled, and most often it is, after securing the frame, carefully insert the glass unit into it.
• Ensure the roof is properly waterproofed. When, after incredible efforts, the window is installed in the roof, one of the last steps remains, but not the last in importance. This refers to the restoration of damaged roof waterproofing. The joints between the window frame and the roofing are taped with a special waterproofing tape. Roof covering around the window is fixed with standard fasteners.
• Secure the trim. Decorative finishing slopes of the attic window/windows are an important final part of the installation work.
• Configure the window opening system. The instructions indicate where the adjustment bolts are located. Using simple manipulations, make the necessary adjustments and check the operation of the mechanism.

Sloping euro-windows differ from dormer windows in that they are mounted directly into the roof at an angle. Window windows were invented in the 19th century, and dormer windows in the post-war fifties of the 20th century. The inclined euro-window is characterized by tightness, practicality, high light transmittance and sound insulation. If there is excess penetration of sunlight into the room, the roof window is covered with canvas or blinds. The light output of an inclined euro-window is 35% higher than that of a pediment or dormer window.

Blinds are installed on inside windows

The outside of the windows can be protected with roller blinds.

A gable window is mounted vertically into a gable wall using a gable collar. Gable frames can be opening or non-opening. Such models serve to increase visibility of the surrounding area.

Hatch window for access to the roof

The roof hatch should organically fit into the appearance of a private cottage. Great solution becomes a hatch window, which can be built into the roof without any problems and looks like a regular inclined euro-window. The hatches harmonize wonderfully with appearance the entire building and the windows installed in it. Types of roof inspection hatches:

1. The emergency roof exit looks similar to a slanted Euro-window. It has all the functions of simple windows. Used for technical inspection and access to the roof. To open the doors, you simply press the handle and the hatch will open automatically using gas shock absorbers. Such structures are installed on roofs with a slope of 15 to 55 degrees.

Characteristics:

• opening angle up to 70 degrees;
• combined opening and ventilation system;
• laminated internal glass;
• outer layer – hardened surface treated with a self-cleaning agent;
• size from 700 x 1200 mm to 1006 x 1200 mm.

The roof hatch greatly simplifies roof maintenance.

1. The operational exit looks like an ordinary attic hatch-window and serves as an exit to the roof. Installed on roofs with a slope from 15 to 55 degrees, equipped with supply valve for attic ventilation. Opens outwards along the lateral axis.

Characteristics:

• Eurowindow opens with a handle;
• the hatch is equipped with a multifunctional double-glazed window;
• the sash can open both to the right and to the left;
• hatch size – 500 by 930 mm.

Operational access to the roof from the attic.

1. The hatch window is installed in attic spaces buildings for technological inspection and access to the roof. You can select the opening type and side. Equipped with provisions for room ventilation. Installed on roofs with a slope from 20 to 65 degrees.

Characteristics:

• the lower ceiling of the frame serves as a step;
• the sash is fixed in 3 places;
• opening angle up to 89 degrees;
• size – 490 x 760 mm.

Attic hatches can have the most Various types opening.

How to choose the right roof windows?

When choosing a European attic window, you should consider a number of features:

• presence of moisture protection;
• presence of seals;
• profile or frame material;
• opening method;
• glass unit strength.

Design features of roof windows https://www.youtube.com/watch?v=UlwbG2I_Hss The design of inclined windows uses a single-chamber double-glazed window, which greatly lightens the load on the fittings and supporting elements. For European attic windows, a frost-resistant, heat-saving double-glazed window is used, which is filled with argon.

Sectional view of attic double-glazed windows.

Double-glazed windows made using triplex technology will protect attic inhabitants from shards of accidentally broken glass. Since two glasses are glued together with a special film, which allows you to hold the fragments. The Easy Clean coating breaks down the dirt accumulated on the euro window under the influence of sunlight, which makes cleaning the glass easier.

Laminated triplex glass will provide excellent protection for your windows.

Important! It is important to pay attention to the location of the window handle. It should be at a comfortable height for use.

Additional options, such as: roller shutters and retaining supports will protect the house from noise, hail, sun and will serve as protection against penetration into the home.

Features of the roof window design

The simplest design of a recessed Euro window. You can use an already erected ceiling and mount a window under an already finished roof. Such windows can be installed at any time.

This design is not only easy to install, but also very practical.

A projecting roof window must be designed during the construction phase. The structure can be mounted for flat and gable roofs. On flat roof it is much easier to install protruding ceilings. The assembled side walls of the structure are covered with boards and covered with roofing covering material, which covers the entire roof.

This design can also be a good addition to the exterior of the house.

An internal roof window can be installed between the beams that support the roof rafters. The support board is installed between the supports, then the window frame is placed on it. A fixing beam secures the frame on top. Side walls and the drain is covered with covering material, which covers the entire roof.

Installation of a roof window.

Installation of a roof window

After the final selection of the model and location of the European attic window, we proceed to its installation. Sequence of installation of an inclined window:

• an opening must be cut in the roof to install the frame;
• the roof is strengthened with additional lags and a frame for the window frame is mounted;
• insulation and waterproofing are installed;
• roofing material is laid;
• window unit is installed.

Master class on installing a roof window https://www.youtube.com/watch?v=U7mQz8E8v9A Before you begin installing a Euro window, you need to strengthen the roof structure and mount the frame for the window frame. Reinforcement is done using rafters located nearby. Jumpers are mounted between them, between which beams are mounted under the window frame. A window frame is installed into the resulting frame. The block should be mounted without glass. The frame should be installed above the roof level, which ensures water drainage. After installing the frame, it is necessary to lay a waterproofing coating to ensure water drainage. Modern models roof windows are equipped additional functions. These include remote control window openings, roller shutters and safety railings forming a small balcony. Roof window on the remote control https://www.youtube.com/watch?v=MLKzwRMPCig